Real Cisco 200-301 Exam Questions for CCNA Certification | Exam Braindumps, Practice Tests Online

Question #1

Refer to the exhibit. An engineer is configuring the New York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path.Which two commands must be configured on the New York router so that it reaches the Lo1 interface of the Atlanta router via Washington when the link betweenNew York and Atlanta goes down? (Choose two.)

A. odify hello interval

B. odify process ID

C. odify priority

D. odify network type

View answer

Correct Answer: AE

Question #2

Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?

A. tandby 10 preempt

B. tandby 10 version 1

C. tandby 10 priority 150

D. tandby 10 version 2

View answer

Correct Answer: A

Question #3

Which command should you enter to verify the priority of a router in an HSRP group?

A. how hsrp

B. how sessions

C. how interfaces

D. how standby

View answer

Correct Answer: D

Question #4

Refer to the exhibit. Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance?

A. outer1(config)#ip route 192

B. outer1(config)#ip route 192

C. outer1(config)#ip route 1 192

D. outer1(config)#ip route 5 192

View answer

Correct Answer: B

Question #5

You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface.Which action can you take to correct the problem in the least disruptive way?

A. eload the OSPF process

B. pecify a loopback address

C. eboot the router

D. ave the router configuration

View answer

Correct Answer: A

Question #6

Which command should you enter to view the error log in an EIGRP for IPv6 environment?

A. how ipv6 eigrp neighbors

B. how ipv6 eigrp topology

C. how ipv6 eigrp traffic

D. how ipv6 eigrp events

View answer

Correct Answer: D

Question #7

Refer to the exhibit. Which two statements about the network environment of router R1 must be true? (Choose two.)Refer to the exhibit. Router R1 must be configured to reach the 10.0.3.0/24 network from the 10.0.1.0/24 segment. Which command must be used to configure the route?

A. oute add 10

B. p route 10

C. oute add 10

D. p route 10

View answer

Correct Answer: D

Question #8

Which two statements about exterior routing protocols are true? (Choose two.)

A. ee Explanation section for answer

View answer

Correct Answer: BC

Question #9

Which three describe the reasons large OSPF networks use a hierarchical design? (Choose three.)

A. 92

B. 92

C. 92

D. 92

View answer

Correct Answer: ABE

Question #10

Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to which IP address does it send the packet?

A. IP

B. SPF

C. GRP

D. IGRP

View answer

Correct Answer: A

Question #11

Refer to the exhibit. On R1 which routing protocol is in use on the route to 192.168.10.1?

A. etwork 172

B. etwork 172

C. etwork 172

D. etwork 172

E. etwork 172

View answer

Correct Answer: D

Question #12

Refer to exhibit. What Administrative distance has route to 192.168.10.1?

A.

B. 0

C. 10

D. 20

View answer

Correct Answer: B

Question #13

Which value is used to determine the active router in an HSRP default configuration?

A. outer loopback address

B. outer IP address

C. outer priority

D. outer tracking number

View answer

Correct Answer: B

Question #14

Refer to the exhibit. If RTR01 is configured as shown, which three addresses will be received by other routers that are running EIGRP on the network? (Choose three.)

A. o additional config is required

B. tandby 1 track ethernet

C. tandby 1 preempt

D. tandby 1 priority 250

View answer

Correct Answer: ACD

Question #15

Which two statements about eBGP neighbor relationships are true? (Choose two.)

A. he router will forward the packet via either Serial0 or Serial1

B. he router will return the packet to its source

C. he router will forward the packet via Serial2

D. he router will drop the packet

View answer

Correct Answer: AB

Question #16

Refer to the exhibit. How will the router handle a packet destined for 192.0.2.156?

A. he area numbers on R1 and R2 are mismatched

B. he IPv6 network addresses on R1 and R2 are mismatched

C. he autonomous system numbers on R1 and R2 are mismatched

D. he router ids on R1 and R2 are mismatched

View answer

Correct Answer: C

Question #17

Which command is used to display the collection of OSPF link states?

A. how ip ospf link-state

B. how ip ospf lsa database

C. how ip ospf neighbors

D. how ip ospf database

View answer

Correct Answer: D

Question #18

Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router)# network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)

A. hese commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172

B. hese commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172

C. hese commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172

D. o further routing configuration is required

View answer

Correct Answer: BCD

Question #19

Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

A. 92

B. 92

C. 92

D. 92

E. 92

View answer

Correct Answer: D

Question #20

Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?

A. 0

B. 0

C. 72

D. 92

View answer

Correct Answer: C

Question #21

Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

A. S numbers must be changed to match on all the routers

B. oopback interfaces must be configured so a DR is elected

C. he no auto-summary command is needed on Router A and Router C

D. outer B needs to have two network statements, one for each connected network

View answer

Correct Answer: A

Question #22

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their commonEthernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?

A. he OSPF area is not configured properly

B. he priority on R1 should be set higher

C. he cost on R1 should be set higher

D. he hello and dead timers are not configured properly

E. backup designated router needs to be added to the network

View answer

Correct Answer: D

Question #23

If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?

A. he IP address of the first Fast Ethernet interface

B. he IP address of the console management interface

C. he highest IP address among its active interfaces

D. he lowest IP address among its active interfaces

E. he priority value until a loopback interface is configured

View answer

Correct Answer: C

Question #24

Refer to the exhibit. Which route type does the routing protocol Code D represent in the output?

A. tatically assigned route

B. oute learned through EIGRP

C. 24 route of a locally configured IP

D. nternal BGP route

View answer

Correct Answer: B

Question #25

An engineer must configure an OSPF neighbor relationship between router R1 and R3. The authentication configuration has been configured and the connecting interfaces are in the same 192.168.1.0/30 subnet. What are the next two steps to complete the configuration? (Choose two.)

A. 09

B. 09

C. 09

D. 09

View answer

Correct Answer: BC

Question #26

Refer to the exhibit. A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?

A. 07

B. 07

C. 07

D. 07

View answer

Correct Answer: D

Question #27

Refer to the exhibit. Router R2 is configured with multiple routes to reach network 10.1.1.0/24 from router R1. Which path is chosen by router R2 to reach the destination network 10.1.1.0/24?

A. tatic

B. IGRP

C. BGP

D. SPF

View answer

Correct Answer: A

Question #28

Refer to the exhibit. What is the next hop address for traffic that is destined to host 10.0.1.5?

A. oopback 0

B. 0

C. 0

D. 0

View answer

Correct Answer: D

Question #29

Refer to the exhibit. A network administrator assumes a task to complete the connectivity between PC A and the File Server. Switch A and Switch B have been partially configured with VLANs 10, 11, 12, and 13. What is the next step in the configuration?

A. dd PC A to VLAN 10 and the File Server to VLAN 11 for VLAN segmentation

B. dd VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation

C. dd a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing

D. dd PC A to the same subnet as the File Server allowing for intra-VLAN communication

View answer

Correct Answer: B

Question #30

DRAG DROP (Drag and Drop is not supported)A network engineer is configuring an OSPFv2 neighbor adjacency. Drag and drop the parameters from the left onto their required categories on the right. Not all parameters are used.Select and Place:

A. ee Explanation section for answer

View answer

Correct Answer: A

Question #31

R1 has learned route 192.168.12.0/24 via IS-IS, OSPF, RIP, and Internal EIGRP. Under normal operating conditions, which routing protocol is installed in the routing table?

A. S-IS

B. nternal EIGRP

C. IP

D. SPF

View answer

Correct Answer: B

Question #32

Refer to the exhibit. The default-information originate command is configured under the R1 OSPF configuration. After testing, workstations on VLAN 20 at SiteB cannot reach a DNS server on the Internet.Which action corrects the configuration issue?

A. dd the default-information originate command on R2

B. dd the always keyword to the default-information originate command on R1

C. onfigure the ip route 0

D. onfigure the ip route 0

View answer

Correct Answer: C

Question #33

Refer to the exhibit. With which metric was the route to host 172.16.0.202 learned?

A.

B. 10

C. 8443

D. 184439

View answer

Correct Answer: C

Question #34

A user configured OSPF in a single area between two routers. A serial interface connecting R1 and R2 is running encapsulation PPP. By default, which OSPF network type is seen on this interface when the user types show ip ospf interface on R1 or R2?

A. onbroadcast

B. oint-to-point

C. oint-to-multipoint

D. roadcast

View answer

Correct Answer: B

Question #35

Which MAC address is recognized as a VRRP virtual address?

A. 000

B. 005

C. 000

D. 007

View answer

Correct Answer: A

Question #36

Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites.Which two tasks must be performed so that the Se0/0/0 interfaces on the Atlanta and Washington routers reach one another? (Choose two.)

A. s-path

B. dministrative distance

C. etric

D. ost

View answer

Correct Answer: BD

Question #37

A router running EIGRP has learned the same route from two different paths. Which parameter does the router use to select the best path?

A. nit

B. -way

C. xchange

D. ull

View answer

Correct Answer: D

Question #38

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?

A. 92

B. 92

C. 92

D. 92

View answer

Correct Answer: D

Question #39

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

A. t starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1

B. t immediately replaces the existing OSPF route in the routing table with the newly configured static route

C. t starts load-balancing traffic between the two default routes

D. t ignores the new static route until the existing OSPF default route is removed

View answer

Correct Answer: D

Question #40

Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

A. p route 209

B. p route 209

C. p route 0

D. p route 0

View answer

Correct Answer: DF

Question #41

Refer to the exhibit. An engineer configured the New York router with static routes that point to the Atlanta and Washington sites. Which command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?

A. pv6 route::/0 Serial 0/0/0

B. pv6 route::/0 Serial 0/0/1

C. pv6 route:0/0 Serial 0/0/0

D. p route 0

E. pv6 route::/0 2000::2

View answer

Correct Answer: A

Question #42

What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?

A. he lowest IP address is incremented by 1 and selected as the router ID

B. he router ID 0

C. o router ID is set, and the OSPF protocol does not run

D. he highest up/up physical interface IP address is selected as the router I

View answer

Correct Answer: D

Question #43

Refer to the exhibit. What is the metric of the route to the 192.168.10.33/28 subnet?

A. 4

B. 10

C. 28

D. 92

E. 93

View answer

Correct Answer: E

Question #44

Refer to the exhibit. Traffic sourced from the loopback0 interface is trying to connect via ssh to the host at 10.0.1.15. What is the next hop to the destination address?

A. 92

B. 92

C. 92

D. 92

View answer

Correct Answer: A

Question #45

When the active router in a VRRP group fails, which router assumes the role and forwards packets?

A. orwarding

B. tandby

C. ackup

D. istening

View answer

Correct Answer: C

Question #46

Which action does the router take as it forwards a packet through the network?

A. he router encapsulates the original packet and then includes a tag that identifies the source router MAC address and transmits it transparently to the destination

B. he router encapsulates the source and destination IP addresses with the sending router IP address as the source and the neighbor IP address as the destination

C. he router replaces the original source and destination MAC addresses with the sending router MAC address as the source and neighbor MAC address as the destination

D. he router replaces the source and destination labels with the sending router interface label as a source and the next hop router label as a destination

View answer

Correct Answer: C

Question #47

Refer to the exhibit. Which two prefixes are included in this routing table entry? (Choose two.)

A. 504

B. 007

C. 050

D. 000

View answer

Correct Answer: AB

Question #48

What is the purpose of using First Hop Redundancy Protocol on a specific subnet?

A. orwards multicast hello messages between routers

B. ends the default route to the hosts on a network

C. nsures a loop-free physical topology

D. ilters traffic based on destination IP addressing

View answer

Correct Answer: B

Question #49

Refer to the exhibit. Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?

A. 1 has an incorrect network command for interface Gi1/0

B. 2 should have its network command in area 1

C. 1 interface Gi1/0 has a larger MTU size

D. 2 is using the passive-interface default command

View answer

Correct Answer: C

Question #50

Refer to the exhibit. When router R1 is sending traffic to IP address 10.56.192.1, which interface or next hop address does it use to route the packet?

A. 0

B.

C. lan57

D. 0

View answer

Correct Answer: A

Question #51

Refer to the exhibit. Load-balanced traffic is coming in from the WAN destined to a host at 172.16.1.190. Which next-hop is used by the router to forward the request?

A. 92

B. 92

C. 92

D. 92

View answer

Correct Answer: C

Question #52

What is a benefit of VRRP?

A. t provides the default gateway redundancy on a LAN using two or more routers

B. t provides traffic load balancing to destinations that are more than two hops from the source

C. t prevents loops in a Layer 2 LAN by forwarding all traffic to a root bridge, which then makes the final forwarding decision

D. t allows neighbors to share routing table information between each other

View answer

Correct Answer: A

Question #53

Refer to the exhibit. Routers R1 and R3 have the default configuration. The router R2 priority is set to 99. Which commands on R3 configure it as the DR in the10.0.4.0/24 network?

A. 3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100

B. 3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 1

C. 3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0

D. 3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100

View answer

Correct Answer: D

Question #54

Refer to the exhibit. A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PC1 to R2. Which configuration must the engineer implement?

A. 1(config)#ip route 10

B. 1(config)#ip route 10

C. 1(config)#ip route 10

D. 1(config)#ip route 10

View answer

Correct Answer: C

Question #55

Refer to the exhibit. All traffic enters the CPE router from interface Serial0/3 with an IP address of 192.168.50.1. Web traffic from the WAN is destined for a LAN network where servers are load-balanced. An IP packet with a destination address of the HTTP virtual IP of 192.168.1.250 must be forwarded. Which routing table entry does the router use?

A. 92

B. 92

C. 92

D. 92

View answer

Correct Answer: D

Question #56

Refer to the exhibit. An engineer assumes a configuration task from a peer. Router A must establish an OSPF neighbor relationship with neighbor 172.1.1.1. The output displays the status of the adjacency after 2 hours. What is the next step in the configuration process for the routers to establish an adjacency?

A. onfigure router A to use the same MTU size as router B

B. onfigure a point-to-point link between router A and router

C. et the router B OSPF ID to the same value as its IP address

D. et the router B OSPF ID to a nonhost address

View answer

Correct Answer: A

Question #57

Refer to the exhibit. Which two configurations must the engineer apply on this network so that R1 becomes the DR? (Choose two.)

A. outer-id 10

B. eighbor 10

C. etwork 10

D. p ospf priority 100

View answer

Correct Answer: AC

Question #58

Refer to the exhibit. Which command configures OSPF on the point-to-point link between routers R1 and R2?

A. 1 ip route 192

B. 1 ip route 192

C. 1 ip route 0

D. 1 ip route 0

View answer

Correct Answer: C

Question #59

Refer to the exhibit. Which next-hop IP address does Router1 use for packets destined to host 10.10.13.158?

A. 0

B. 0

C. 0

D. 0

View answer

Correct Answer: A

Question #60

Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.1. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.1.1.19?

A. 0/0

B. 0/1

C. 0/4

D. 0/3

View answer

Correct Answer: A

Question #61

Refer to the exhibit. Which route must be configured on R1 so that OSPF routing is used when OSPF is up, but the server is still reachable when OSPF goes down?

A. p route 10

B. p route 10

C. p route 10

D. p route 10

View answer

Correct Answer: A

Question #62

Refer to the exhibit. What is the next hop for traffic entering R1 with a destination of 10.1.2.126?

A. 0

B. 0

C. 0

D. 0

View answer

Correct Answer: A

Question #63

Refer to the exhibit. Which prefix did router R1 learn from internal EIGRP?

A. 92

B. 92

C. 72

D. 92

View answer

Correct Answer: D

Question #64

Refer to the exhibit. R5 is the current DR on the network, and R4 is the BDR. Their interfaces are flapping, so a network engineer wants the OSPF network to elect a different DR and BDR. Which set of configurations must the engineer implement?

A. 4(config)#interface gi0/0 R4(config-if)#ip ospf priority 20 R5(config)#interface gi0/0 R5(config-if)#ip ospf priority 10

B. 5(config)#interface gi0/0 R5(config-if)#ip ospf priority 120 R4(config)#interface gi0/0 R4(config-if)#ip ospf priority 110

C. 3(config)#interface gi0/0 R3(config-if)#ip ospf priority 255 R2(config)#interface gi0/0 R2(config-if)#ip ospf priority 240

D. 2(config)#interface gi0/0 R2(config-if)#ip ospf priority 259 R3(config)#interface gi0/0 R3(config-if)#ip ospf priority 256

View answer

Correct Answer: C

Question #65

Refer to the exhibit. Web traffic is coming in from the WAN interface. Which route takes precedence when the router is processing traffic destined for the LAN network at 10.0.10.0/24?

A. ia next-hop 10

B. ia next-hop 10

C. ia next-hop 10

D. ia next-hop 10

View answer

Correct Answer: A

Question #66

Refer to the exhibit. A packet sourced from 10.10.10.1 is destined for 10.10.8.14. What is the subnet mask of the destination route?

A. 55

B. 55

C. 55

D. 55

View answer

Correct Answer: B

Question #67

Refer to the exhibit. An engineer must configure router R2 so it is elected as the DR on the WAN subnet. Which command sequence must be configured?

A. nterface gigabitethernet0/0 ip address 10

B. nterface gigabitethernet0/0 ip address 10

C. nterface gigabitethernet0/0 ip address 10

D. nterface gigabitethernet0/0 ip address 10

View answer

Correct Answer: B

Question #68

An engineer is configuring router R1 with an IPv6 static route for prefix 2019:C15C:0CAF:E001::/64. The next hop must be 2019:C15C:0CAF:E002::1. The route must be reachable via the R1 Gigabit 0/0 interface. Which command configures the designated route?

A. 1(config-if)#ip route 2019:C15C:0CAF:E001::/64 GigabitEthernet 0/0

B. 1(config)#ip route 2019:C15C:0CAF:E001::/64 GigabitEthernet 0/0

C. 1(config-if)#ipv6 route 2019:C15C:0CAF:E001::/64 2019:C15C:0CAF:E002::1

D. 1(config)#ipv6 route 2019:C15C:0CAF:E001::/64 2019:C15C:0CAF:E002::1

View answer

Correct Answer: D

Question #69

Refer to the exhibit. Which IPv6 configuration is required for R17 to successfully ping the WAN interface on R18?

A. 17# ! no ip domain lookup ip cef ipv6 cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:4::302

B. 17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:3::301

C. 17# ! no ip domain lookup ip cef ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:5::101

D. 17# ! no ip domain lookup ip cef ipv6 unicast-routing ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:2::201/64 ! Interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:DB8:3::201/64 ! no cdp log mismatch duplex ipv6 route 2001:DB8:4::/64 2001:DB8:2::201

View answer

Correct Answer: B

Question #70

Refer to the exhibit. A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?

A. p route 0

B. p route 0

C. p route 0

D. p route 0

View answer

Correct Answer: A

Question #71

OSPF must be configured between routers R1 and R2. Which OSPF configuration must be applied to router R1 to avoid a DR'BDR election?

A. outer ospf 1 network 192

B. outer ospf 1 network 192

C. outer ospf 1 network 192

D. outer ospf 1 network 192

View answer

Correct Answer: D

Question #72

Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?

A. 1(config)#ip route 172

B. 1(config)#ip route 172

C. 1(config)#ip route 172

D. 1(config)#ip route 172

View answer

Correct Answer: C

Question #73

Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?

A. p route 0

B. p route 0

C. p route 0

D. p route 0

View answer

Correct Answer: D

Question #74

Refer to the exhibit. Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?

A. onfigure the router A interfaces with the highest OSPF priority value within the area

B. onfigure router B and router C as OSPF neighbors of router A

C. onfigure the OSPF priority on router A with the lowest value between the three routers

D. onfigure router A with a fixed OSPF router ID

View answer

Correct Answer: A

Question #75

Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?

A. 0/10

B. 0/11

C. 0/12

D. 0/1

View answer

Correct Answer: B

Question #76

Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to 10.10.13.128/25 at Site A?

A. t sends packets out of interface Fa0/1

B. t sends packets out of interface Fa0/2

C. t load-balances traffic out of Fa0/1 and Fa0/2

D. t is unreachable and discards the traffic

View answer

Correct Answer: D

Question #77

Refer to the exhibit. Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that each of the four Gigabit interfaces has the same route to 10 10.0.0/16.Which interface will R1 choose to send traffic to reach the route?

A. igabitEthernet0/0

B. igabitEthernet0/1

C. igabitEthernet0/2

D. igabitEthernet0/3

View answer

Correct Answer: B

Question #78

Refer to the exhibit. Which network prefix was learned via EIGRP?

A. 72

B. 07

C. 92

D. 92

View answer

Correct Answer: D

Question #79

Refer to the exhibit. Which command must be issued to enable a floating static default route on router A?

A. p route 0

B. p route 0

C. p default-gateway 192

D. p route 0

View answer

Correct Answer: A

Question #80

Refer to the exhibit. Which configuration allows routers R14 and R86 to form an OSPFv2 adjacency while acting as a central point for exchanging OSPF information between routers?

A. 14# interface FastEthernet0/0 ip address 10

B. 14# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10

C. 14# interface FastEthernet0/0 ip address 10

D. 14# interface FastEthernet0/0 ip address 10

View answer

Correct Answer: C

Question #81

Refer to the exhibit. When an administrator executes the show ip route command on router D to view its routing table, which value is displayed for the administrative distance for the route to network 192.168 1.0?

A. 10

B. 20

C. 70

D. 0

View answer

Correct Answer: A

Question #82

Refer to the exhibit Routers R1 and R2 have been configured with their respective LAN interfaces. The two circuits are operational and reachable across WAN.Which command set establishes failover redundancy if the primary circuit goes down?

A. 1(config)#ip route 0

B. 1(config)#ip route 10

C. 1(config)#ip route 10

D. 1(config)#ip route 0

View answer

Correct Answer: D

Question #83

Refer to the exhibit. R1 learns all routes via OSPF. Which command configures a backup static route on R1 to reach the 192.168.20 0/24 network via R3?

A. 1(config)#ip route 192

B. 1(config)#ip route 192

C. 1(config)#ip route 192

D. 1(config)#ip route 192

View answer

Correct Answer: A

Question #84

Refer to the exhibit. R1 has taken the DROTHER role in the OSPF DR/BDR election process. Which configuration must an engineer implement so that R1 is elected as the DR?

A. 1(config)#interface FastEthernet 0/0 R1(config-if)#ip ospf priority 1 R1#clear ip ospf process

B. 3(config)#interface FastEthernet 0/1 R3(config-if)#ip ospf priority 200 R3#clear ip ospf process

C. 2(config)#interface FastEthernet 0/2 R2(config-if)#ip ospf priority 1 R2#clear ip ospf process

D. 1(config)#interface FastEthernet 0/0 R1(config-if)#ip ospf priority 200 R1#clear ip ospf process

View answer

Correct Answer: D

Question #85

Which SDN plane forwards user-generated traffic?

A. anagement plane

B. ontrol plane

C. olicy plane

D. ata plane

View answer

Correct Answer: D

Question #86

An application in the network is being scaled up from 300 servers to 600. Each server requires 3 network connections to support production, backup, and management traffic. Each connection resides on a different subnet. The router configuration for the production network must be configured first using a subnet in the 10.0.0.0/8 network. Which command must be configured on the interface of the router to accommodate the requirements and limit wasted IP address space?

A. p address 10

B. p address 10

C. p address 10

D. p address 10

View answer

Correct Answer: A

Question #87

Refer to the exhibit. Which interface is chosen to forward traffic to the host at 192.168.0.55?

A. igabitEthernet0/3

B. ull0

C. igabitEthernet0/1

D. igabitEthernet0/2

View answer

Correct Answer: C

Question #88

Refer to the exhibit. The administrator must configure a floating static default route that points to 2001:db8:1234:2::1 and replaces the current default route only if it fails. Which command must the engineer configure on the CPE?

A. pv6 route ::/0 2001:db8:1234:2::1 3

B. pv6 route ::/128 2001:db8:1234:2::1 3

C. pv6 route ::/0 2001:db8:1234:2::1 1

D. pv6 route ::/0 2001:db8:1234:2::1 2

View answer

Correct Answer: A

Question #89

Refer to the exhibit. Router OldR is replacing another router on the network with the intention of having OldR and R2 exchange routes. After the engineer applied the initial OSPF configuration, the routes were still missing on both devices. Which command sequence must be issued before the clear IP ospf process command is entered to enable the neighbor relationship?

A. ldR(config)#interface g0/0/0 OldR(config-if)#ip ospf hello-interval 15

B. ldR(config)#router ospf 1 OldR(config-router)#network 192

C. ldR(config)#interface g0/0/0 OldR(config-if)#ip ospf dead-interval 15

D. ldR(config)#router ospf 1 OldR(config-router)#no router-id 192

View answer

Correct Answer: D

Question #90

DRAG DROP (Drag and Drop is not supported)Refer to the exhibit. Drag and drop the prefix lengths from the left onto the corresponding prefixes on the right. Not all prefixes are used.Select and Place:

A. ee Explanation section for answer

View answer

Correct Answer: A

Question #91

Refer to the exhibit. What is the subnet mask for route 172.16.4.0?

A. 55

B. 55

C. 55

D. 55

View answer

Correct Answer: C

Question #92

Refer to the exhibit. A static route must be configured on R14 to forward traffic for the 172.21.34.0/25 network that resides on R86. Which command must be used to fulfill the request?

A. p route 172

B. p route 172

C. p route 172

D. p route 172

View answer

Correct Answer: B

Question #93

Refer to the exhibit. The network engineer is configuring router R2 as a replacement router on the network. After the initial configuration is applied, it is determined that R2 failed to show R1 as a neighbor. Which configuration must be applied to R2 to complete the OSPF configuration and enable it to establish the neighbor relationship with R1?

A. 2(config)#router ospf 1 R2(config-router)#network 192

B. 2(config)#interface g0/0/0 R2(config-if)#ip ospf hello-interval 10

C. 2(config)#interface g0/0/0 R2(config-if)#ip ospf dead-interval 40

D. 2(config)#router ospf 1 R2(config-router)#router-id 192

View answer

Correct Answer: C

Question #94

Refer to the exhibit. All interfaces are configured with duplex auto and ip ospf network broadcast. Which configuration allows routers R14 and R86 to form anOSPFv2 adjacency and act as a central point for exchanging OSPF information between routers?

A. 14# interface FastEthernet0/0 ip address 10

B. 14# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10

C. 14# interface FastEthernet0/0 ip address 10

D. 14# interface Loopback0 ip ospf 10 area 0 interface FastEthernet0/0 ip address 10

View answer

Correct Answer: A

Question #95

A packet from a company's branch office is destined to host 172.31.0.1 at headquarters. The sending router has three possible matches in its routing table for the packet: prefixes 172.31.0.0/16, 172.31.0.0/24, and 172.31.0.0/25. How does the router handle the packet?

A. t sends the traffic via prefix 172

B. t sends the traffic via prefix 172

C. t sends the traffic via prefix 172

D. t sends the traffic via the default gateway 0

View answer

Correct Answer: C

Question #96

Refer to the exhibit. An engineer is asked to configure router R1 so that it forms an OSPF single-area neighbor relationship with R2. Which command sequence must be implemented to configure the router?

A. outer ospf 100 network 10

B. outer ospf 100 network 10

C. outer ospf 10 network 10

D. outer ospf 10 network 10

View answer

Correct Answer: C

Question #97

Refer to the exhibit. All routers in the network are configured. R2 must be the DR. After the engineer connected the devices, R1 was elected as the DR. Which command sequence must be configured on R2 to be elected as the DR in the network?

A. 2(config)#intergface gi0/0 R2(config-if)#ip ospf priority 100

B. 2(config)#router ospf 1 R2(config-router)#router-id 192

C. 2(config)#router ospf 1 R2(config-router)#router-id 10

D. 2(config)#intergface gi0/0 R2(config-if)#ip ospf priority 1

View answer

Correct Answer: A

Question #98

Refer to the exhibit. What is the subnet mask of the route to the 10.10.13.160 prefix?

A. 55

B. 55

C. 55

D. 55

View answer

Correct Answer: D

Question #99

Refer to the exhibit. Which two commands, when configured on router R1, fulfill these requirements? (Choose two.)-Packets toward the entire network 2001:db8:23::/64 must be forwarded through router R2.-Packets toward host 2001:db8:23::14 preferably must be forwarded through R3.

A. p route 10

B. p route 10

C. p route 10

D. p route 10

View answer

Correct Answer: BC

Question #100

Refer to the exhibit. Traffic from R1 to the 10.10.2.0/24 subnet uses 192.168.1.2 as its next hop. A network engineer wants to update the R1 configuration so that traffic with destination 10.10 2.1 passes through router R3, and all other traffic to the 10.10.2.0/24 subnet passes through R2. Which command must be used?

A. 1(config)#ip route 10

B. 1(config)#ip route 10

C. 1(config)#ip route 10

D. 1(config)#ip route 10

View answer

Correct Answer: D

Question #101

Refer to the exhibit. An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the server at 192.168.2.2?

A. 192

B. 192

C. 192

D. 192

View answer

Correct Answer: B

Question #102

Refer to the exhibit. What is the prefix length for the route that router1 will use to reach host A?

A. 25

B. 27

C. 28

D. 29

View answer

Correct Answer: D

Question #103

Refer to the exhibit. After applying this configuration to router R1, a network engineer is verifying the implementation. If all links are operating normally, and the engineer sends a series of packets from PC1 to PC3, how are the packets routed?

A. hey are distributed sent round robin to interfaces S0/0/0 and S0/0/1

B. hey are routed to 10

C. hey are routed to 192

D. hey are routed to 172

View answer

Correct Answer: D

Question #104

Refer to the exhibit. When router R1 receives a packet with destination IP address 10.56.0.62, through which interface does it route the packet?

A. lan58

B. ull0

C. lan59

D. lan60

View answer

Correct Answer: A

Question #105

Refer to the exhibit. How much OSPF be configured on the GigabitEthernet0/0 interface of the neighbor device to achieve the destined neighbor relationship?

A. outer(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf cost 5

B. outer(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf priority 1

C. outer(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf area 2

D. outer(config)#interface GigabitEthernet 0/0 Router(config-if)#ip ospf network point-to-point

View answer

Correct Answer: D

Question #106

Refer to the exhibit. An engineer just installed network 10.120.10.0/24. Which configuration must be applied to the R14 router to add the new network to its OSPF routing table?

A. outer ospf 100 Network 10

B. outer ospf 120 Network 10

C. outer ospf 100 area 0 Network 10

D. outer ospf 100 Network 10

View answer

Correct Answer: A

Question #107

What is the MAC address used with VRRP as a virtual address?

A. 0-05-42-38-53-31

B. 0-00-5E-00-01-0a

C. 0-00-0C-07-AD-89

D. 0-07-C0-70-AB-01

View answer

Correct Answer: B

Question #108

Why would VRRP be implemented when configuring a new subnet in a multivendor environment?

A. hen a gateway protocol is required that supports more than two Cisco devices for redundancy

B. o interoperate normally with all vendors and provide additional security features for Cisco devices

C. o ensure that the spanning-tree forwarding path to the gateway is loop-free

D. o enable normal operations to continue after a member failure without requiring a change in a host ARP cache

View answer

Correct Answer: B

Question #109

Why implement VRRP?

A. o hand over to end users the autodiscovery of virtual gateways

B. o provide end users with a virtual gateway in a multivendor network

C. o leverage a weighting scheme to provide uninterrupted service

D. o detect link failures without the overhead of Bidirectional Forwarding Detection

View answer

Correct Answer: B

Question #110

Which type of address is shared by routers in a HSRP implementation and used by hosts on the subnet as their default gateway address?

A. ulticast address

B. irtual IP address

C. oopback IP address

D. roadcast address

View answer

Correct Answer: B

Question #111

By default, which virtual MAC address does HSRP group 14 use?

A. 0:05:5e:19:0c:14

B. 0:05:0c:07:ac:14

C. 4:15:26:73:3c:0e

D. 0:00:0c:07:ac:0e

View answer

Correct Answer: D

Question #112

Refer to the exhibit. Router R1 is added to the network and configured with the 10.0.0.64/26 and 10.0.20.0/26 subnets. However, traffic destined for the LAN onR3 is not accessible. Which command when executed on R1 defines a static route to reach the R3 LAN?

A. p route 10

B. p route 10

C. p route 10

D. p route 10

View answer

Correct Answer: D

Question #113

A router has two static routes to the same destination network under the same OSPF process. How does the router forward packets to the destination if the net- hop devices are different?

A. he router chooses the route with the oldest age

B. he router chooses the next hop with the lowest IP address

C. he router chooses the next hop with the lowest MAC address

D. he router load-balances traffic over all routes to the destination

View answer

Correct Answer: D

Question #114

What does the implementation of a first-hop redundancy protocol protect against on a network?

A. efault gateway failure

B. GP neighbor flapping

C. panning-tree loops

D. oot-bridge loss

View answer

Correct Answer: A

Question #115

Which feature or protocol is required for an IP SLA to measure UDP jitter?

A. LDP

B. EM

C. DP

D. TP

View answer

Correct Answer: D

Question #116

Refer to the exhibit. Which feature is enabled by this configuration?

A. tatic NAT translation

B. DHCP pool

C. dynamic NAT address pool

D. AT

View answer

Correct Answer: C

Question #117

Which NAT term is defined as a group of addresses available for NAT use?

A. AT pool

B. ynamic NAT

C. tatic NAT

D. ne-way NAT

View answer

Correct Answer: A

Question #118

Which command can you enter to allow Telnet to be supported in addition to SSH?

A. ransport input telnet ssh

B. ransport input telnet

C. o transport input telnet

D. rivilege level 15

View answer

Correct Answer: A

Question #119

Refer to the exhibit. After you apply the given configuration to a router, the DHCP clients behind the device cannot communicate with hosts outside of their subnet.Which action is most likely to correct the problem?

A. onfigure the dns server on the same subnet as the clients

B. ctivate the dhcp pool

C. orrect the subnet mask

D. onfigure the default gateway

View answer

Correct Answer: D

Question #120

Refer to the exhibit. Which rule does the DHCP server use when there is an IP address conflict?

A. he address is removed from the pool until the conflict is resolved

B. he address remains in the pool until the conflict is resolved

C. nly the IP detected by Gratuitous ARP is removed from the pool

D. nly the IP detected by Ping is removed from the pool

E. he IP will be shown, even after the conflict is resolved

View answer

Correct Answer: A

Question #121

Which command can you enter to determine the addresses that have been assigned on a DHCP Server?

A. how ip DHCP database

B. how ip DHCP pool

C. how ip DHCP binding

D. how ip DHCP server statistic

View answer

Correct Answer: C

Question #122

What is the authoritative source for an address lookup?

A. recursive DNS search

B. he operating system cache

C. he ISP local cache

D. he browser cache

View answer

Correct Answer: A

Question #123

Which command is used to verify the DHCP relay agent address that has been set up on your Cisco IOS router?

A. how ip interface brief

B. how ip dhcp bindings

C. how ip route

D. how ip interface

E. how interface

View answer

Correct Answer: D

Question #124

Which type of information resides on a DHCP server?

A. list of the available IP addresses in a pool

B. list of public IP addresses and their corresponding names

C. sernames and passwords for the end users in a domain

D. list of statically assigned MAC addresses

View answer

Correct Answer: A

Question #125

What are two roles of Domain Name Services (DNS)? (Choose two.)

A. how ip interface GigabitEthernet 0/0 dhcp

B. how interface GigabitEthernet 0/0

C. how ip interface dhcp

D. how ip interface GigabitEthernet 0/0

E. how ip interface GigabitEthernet 0/0 brief

View answer

Correct Answer: DE

Question #126

What will happen if you configure the logging trap debug command on a router?

A. t causes the router to send messages with lower severity levels to the syslog server

B. t causes the router to send all messages with the severity levels Warning, Error, Critical, and Emergency to the syslog server

C. t causes the router to send all messages to the syslog server

D. t causes the router to stop sending all messages to the syslog server

View answer

Correct Answer: C

Question #127

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)

A. ee Explanation section for answer

View answer

Correct Answer: BDF

Question #128

DRAG DROP (Drag and Drop is not supported)Drag and drop the network protocols from the left onto the correct transport services on the right.Select and Place:

A. RP

B. NMP

C. MTP

D. DP

View answer

Correct Answer: A

Question #129

Which command enables a router to become a DHCP client?

A. p address dhcp

B. p dhcp client

C. p helper-address

D. p dhcp pool

View answer

Correct Answer: A

Question #130

Which function does an SNMP agent perform?

A. t sends information about MIB variables in response to requests from the NMS

B. t manages routing between Layer 3 devices in a network

C. t coordinates user authentication between a network device and a TACACS+ or RADIUS server

D. t requests information from remote network nodes about catastrophic system events

View answer

Correct Answer: A

Question #131

What are two roles of the Dynamic Host Configuration Protocol (DHCP)? (Choose two.)

A. tp peer

B. tp master

C. tp authenticate

D. tp server

View answer

Correct Answer: BD

Question #132

What event has occurred if a router sends a notice level message to a syslog server?

A. certificate has expired

B. n interface line has changed status

C. TCP connection has been torn down

D. n ICMP connection has been built

View answer

Correct Answer: B

Question #133

Refer to the exhibit. An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct, which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two.)

A. 0

B. 0

C. 72

D. 72

View answer

Correct Answer: BC

Question #134

If a notice-level message is sent to a syslog server, which event has occurred?

A. network device has restarted

B. debug operation is running

C. routing instance has flapped

D. n ARP inspection has failed

View answer

Correct Answer: C

Question #135

DRAG DROP (Drag and Drop is not supported)Drag and drop the functions from the left onto the correct network components on the right.Select and Place:

A. ee Explanation section for answer

View answer

Correct Answer: A

Question #136

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two.)

A. t allows directly connected neighbors to share configuration information

B. t reduces routing failures by allowing Layer 3 load balancing between OSPF neighbors that have the same link metric

C. t allows a router to use bridge priorities to create multiple loop-free paths to a single destination

D. t reduces routing failures by allowing more than one router to represent itself as the default gateway of a network

View answer

Correct Answer: AC

Question #137

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

A. nable configure terminal ip nat pool mypool 192

B. nable configure terminal ip nat pool mypool 192

C. nable configure terminal ip nat pool mypool 192

D. nable configure terminal ip nat pool mypool 192

View answer

Correct Answer: D

Question #138

When the active router in an HSRP group fails, which router assumes the role and forwards packets?

A. orwarding

B. istening

C. tandby

D. ackup

View answer

Correct Answer: C

Question #139

What protocol allows an engineer to back up 20 network router configurations globally while using the copy function?

A. CP

B. MTP

C. TP

D. NMP

View answer

Correct Answer: D

Question #140

Which type of address is the public IP address of a NAT device?

A. utside global

B. utside local

C. nside global

D. nside local

E. utside public

View answer

Correct Answer: C

Question #141

Which two pieces of information can you determine from the output of the show ntp status command? (Choose two.)

A. ource

B. tatic

C. ool

D. verload

View answer

Correct Answer: BD

Question #142

Which keyword in a NAT configuration enables the use of one outside IP address for multiple inside hosts?

A. LDP

B. DP

C. P SLA

D. EM

View answer

Correct Answer: D

Question #143

Which feature or protocol determines whether the QOS on the network is sufficient to support IP services?

A. raffic policing

B. ound-robin scheduling

C. ow-latency queuing

D. xpedited forwarding

View answer

Correct Answer: C

Question #144

DRAG DROP (Drag and Drop is not supported)Drag and drop the SNMP components from the left onto the descriptions on the right.Select and Place:

A. ee Explanation section for answer

View answer

Correct Answer: A

Question #145

What is the purpose of traffic shaping?

A. o be a marking mechanism that identifies different flows

B. o provide fair queuing for buffered flows

C. o mitigate delays over slow links

D. o limit the bandwidth that a flow can use

View answer

Correct Answer: D

Question #146

What is a function of TFTP in network operations?

A. ransfers IOS images from a server to a router for firmware upgrades

B. ransfers a backup configuration file from a server to a switch using a username and password

C. ransfers configuration files from a server to a router on a congested link

D. ransfers files between file systems on a router

View answer

Correct Answer: A

Question #147

What is a DHCP client?

A. workstation that requests a domain name associated with its IP address

B. host that is configured to request an IP address automatically

C. server that dynamically assigns IP addresses to hosts

D. router that statically assigns IP addresses to hosts

View answer

Correct Answer: B

Question #148

Where does the configuration reside when a helper address is configured lo support DHCP?

A. n the router closest to the server

B. n the router closest to the client

C. n every router along the path

D. n the switch trunk interface

View answer

Correct Answer: B

Question #149

What facilitates a Telnet connection between devices by entering the device name?

A. NMP

B. NS lookup

C. yslog

D. TP

View answer

Correct Answer: B

Question #150

When deploying syslog, which severity level logs informational messages?

A.

B.

C.

D.

View answer

Correct Answer: D

Question #151

DRAG DROP (Drag and Drop is not supported) Refer to the exhibit. An engineer is configuring the router to provide static NAT for the webserver. Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the fight.Select and Place:

A. ee Explanation section for answer

View answer

Correct Answer: A

Question #152

Which two QoS tools provide congestion management? (Choose two.)

A. RED

B. IFO

C. FQ

D. Q

View answer

Correct Answer: AE

Question #153

Which QoS tool is used to optimize voice traffic on a network that is primarily intended for data traffic?

A. lient exclusion

B. HCP address assignment

C. assive client

D. tatic IP tunneling

View answer

Correct Answer: D

Question #154

An engineer is installing a new wireless printer with a static IP address on the Wi-Fi network. Which feature must be enabled and configured to prevent connection issues with the printer?

A. HCPOFFER

B. HCP relay agent

C. HCP server

D. HCPDISCOVER

View answer

Correct Answer: C

Question #155

Refer to the exhibit. The ntp server 192.168.0.3 command has been configured on router 1 to make it an NTP client of router 2. Which command must be configured on router 2 so that it operates in server-only mode and relies only on its internal clock?

A. outer2(config)#ntp server 172

B. outer2(config)#ntp server 192

C. outer2(config)#ntp passive

D. outer2(config)#ntp master 4

View answer

Correct Answer: D

Question #156

Which protocol requires authentication to transfer a backup configuration file from a router to a remote server?

A. TP

B. MTP

C. FTP

D. TP

View answer

Correct Answer: A

Question #157

Which condition must be met before an NMS handles an SNMP trap from an agent?

A. he NMS must receive the same trap from two different SNMP agents to verify that it is reliable

B. he NMS must receive a trap and an inform message from the SNMP agent within a configured interval

C. he NMS software must be loaded with the MIB associated with the trap

D. he NMS must be configured on the same router as the SNMP agent

View answer

Correct Answer: C

Question #158

An engineer is configuring switch SW1 to act as an NTP server when all upstream NTP server connectivity fails. Which configuration must be used?

A. W1# config t SW1(config)#ntp peer 192

B. W1# config t SW1(config)#ntp master SW1(config)#ntp server192

C. W1# config t SW1(config)#ntp backup SW1(config)#ntp server192

D. W1# config t SW1(config)#ntp server192

View answer

Correct Answer: B

Question #159

A network administrator must enable DHCP services between two sites. What must be configured for the router to pass DHCPDISCOVER messages on to the server?

A. HCP Binding

B. DHCP Relay Agent

C. HCP Snooping

D. DHCP Pool

View answer

Correct Answer: B

Question #160

Which level of severity must be set to get informational syslogs?

A. lert

B. ritical

C. otice

D. ebug

View answer

Correct Answer: D

Question #161

On workstations running Microsoft Windows, which protocol provides the default gateway for the device?

A. TP

B. HCP

C. NMP

D. NS

View answer

Correct Answer: B

Question #162

Refer to the exhibit. Which configuration must be applied to the router that configures PAT to translate all addresses in VLAN 200 while allowing devices on VLAN100 to use their own IP addresses?

A. outer1(config)#access-list 99 permit 192

B. outer1(config)#access-list 99 permit 192

C. outer1(config)#access-list 99 permit 209

D. outer1(config)#access- list 99 permit 209

View answer

Correct Answer: A

Question #163

Refer to the exhibit. Which two commands must be added to update the configuration of router R1 so that it accepts only encrypted connections? (Choose two.)

A. nmp-server user

B. nmp-server host

C. nmp-server enable traps

D. nmp-server community

View answer

Correct Answer: CE

Question #164

Which command implies the use of SNMPv3?

A. tp authenticate ntp authentication-key 2 sha1 CISCO123 ntp source Loopback0 ntp access-group server-only 10 ntp master 2 ! access-list 10 permit udp host 209

B. tp authenticate ntp authentication-key 2 md5 CISCO123 ntp interface Loopback0 ntp access-group server-only 10 ntp stratum 2 ! access-list 10 permit 209

C. tp authenticate ntp authentication-key 2 md5 CISCO123 ntp source Loopback0 ntp access-group server-only 10 ntp master 2 ! access-list 10 permit 209

D. tp authenticate ntp authentication-key 2 md5 CISCO123 ntp source Loopback0 ntp access-group server-only 10 ntp stratum 2 ! access-list 10 permit udp host 209

View answer

Correct Answer: A

Question #165

What is a capability of FTP in network management operations?

A. ffers proprietary support at the session layer when transferring data

B. ses separate control and data connections to move files between server and client

C. ncrypts data before sending between data resources

D. evices are directly connected and use UDP to pass file information

View answer

Correct Answer: B

Question #166

A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?

A. assword password

B. p ssh authentication-retries 2

C. p domain-name domain

D. rypto key generate rsa modulus 1024

View answer

Correct Answer: C

Question #167

Which QoS traffic handling technique retains excess packets in a queue and reschedules these packets for later transmission when the configured maximum bandwidth has been surpassed?

A. raffic policing

B. eighted random early detection

C. raffic prioritization

D. raffic shaping

View answer

Correct Answer: D

Question #168

Which command must be entered to configure a DHCP relay?

A. p dhcp relay

B. p dhcp pool

C. p address dhcp

D. p helper-address

View answer

Correct Answer: D

Question #169

Refer to the exhibit. The DHCP server and clients are connected to the same switch. What is the next step to complete the DHCP configuration to allow clients onVLAN 1 to receive addresses from the DHCP server?

A. onfigure the ip dhcp snooping trust command on the interface that is connected to the DHCP client

B. onfigure ip dhcp relay information option command on the interface that is connected to the DHCP server

C. onfigure ip dhcp snooping trust command on the interface that is connected to the DHCP server

D. onfigure the ip dhcp information option command on the interface that is connected to the DHCP client

View answer

Correct Answer: C

Question #170

A network analyst is tasked with configuring the date and time on a router using EXEC mode. The date must be set to January 1, 2020 and the time must be set to12:00 am. Which command should be used?

A. lock timezone

B. lock summer-time date

C. lock summer-time recurring

D. lock set

View answer

Correct Answer: D

Question #171

Which event has occurred if a router sends a notice level message to a syslog server?

A. n interface line has changed status

B. n ICMP connection has been built

C. TCP connection has been torn down

D. certificate has expired

View answer

Correct Answer: A

Question #172

Which command creates a static NAT binding for a PC address of 10.1.1.1 to the public routable address 209.165.200.225 assigned to the PC?

A. 1(config)#ip nat inside source static 10

B. 1(config)#ip nat outside source static 209

C. 1(config)#ip nat inside source static 209

D. 1(config)#ip nat outside source static 10

View answer

Correct Answer: A

Question #173

What prevents a workstation from receiving a DHCP address?

A. TP

B. TP

C. 02

D. TP

View answer

Correct Answer: C

Question #174

What is a feature of TFTP?

A. ffers anonymous user login ability

B. ses two separate connections for control and data traffic

C. elies on the well-known TCP port 20 to transmit data

D. rovides secure data transfer

View answer

Correct Answer: A

Question #175

Which QoS forwarding per-hop behavior changes a specific value in a packet header to set the class of service for the packet?

A. haping

B. lassification

C. olicing

D. arking

View answer

Correct Answer: D

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now

Real Cisco 200-301 Exam Questions for CCNA Certification | Exam Braindumps, Practice Tests Online

View The Updated 200-301 Exam Questions

View The Updated CCNA Exam Questions

View Answers after Submission

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE! Get Now

Real Cisco 200-301 Exam Questions for CCNA Certification | Exam Braindumps, Practice Tests Online

View The Updated 200-301 Exam Questions

View The Updated CCNA Exam Questions

View Answers after Submission

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now