DON'T WANT TO MISS A THING?

Certification Exam Passing Tips

Latest exam news and discount info

Curated and up-to-date by our experts

Yes, send me the newsletter

Pass Your CCNP 300-420 Exam with Practice Tests 2024 Updated, Cisco Enterprise Networks | SPOTO

Ensure your success in the 300-420 ENSARI exam with SPOTO's newly updated 2024 practice tests. Our comprehensive exam materials contain hundreds of the latest sample questions covering advanced routing, enterprise campus networks, WAN, security services, network services, and SDA concepts from the actual test. Gain confidence through regular online exam practice using our realistic mock exams and exam simulator that mimic the real test environment. Detailed explanations for each exam answer solidify your understanding and identify areas for improvement. Don't rely on outdated resources - leverage SPOTO's up-to-date 300-420 exam questions, answers, and free test dumps to thoroughly prepare and pass on your first attempt.
Take other online exams
Question #1
Topic 1Which design consideration must be made when using IPv6 overlay tunnels?
A. Overlay tunnels that connect isolated IPv6 networks are considered a final IPv6 network architecture
B. Overlay tunnels should only be considered as a transition technique toward a permanent solution
C. Overlay tunnels should be configured only between border devices and require only the IPv6 protocol stack
D. Overlay tunneling encapsulates IPv4 packets in IPv6 packets for delivery across an IPv6 infrastructure
View answer
Correct Answer: C

View The Updated 300-420 Exam Questions

SPOTO Provides 100% Real 300-420 Exam Questions for You to Pass Your 300-420 Exam!

Get 300-420 Practice Test
Question #2
You have configured three routers in HSRP group 10 to provide gateway redundancy for VLAN 56. Your intention was for Router 1 to be the active router in the group and for Router 3 to be the standby router. Furthermore, in the event that Router 1 became unavailable, resulting in Router 3 becoming active, you intended for Router 1 to resume its role as active when it came back online. However, you discover that in practice, Router 1 does NOT resume the active role when it comes back online. What command shoul
A. router1(config)# interface VLAN 56router1(config-if)# standby 10 preempt
B. router1(config)# interface VLAN 10router1(config-if)# standby 56 preempt
C. router1(config)# standby 10 preempt
D. router1(config)# standby 56 preempt
View answer
Correct Answer: A
Question #3
What command would display a single line of information for each virtual gateway or virtual forwarder on a switch?
A. switch# show glbp
B. switch# show glbp brief
C. switch# show standby
D. switch# show standby brief
View answer
Correct Answer: B
Question #4
Topic 1A company is running BGP on a single router, which has two connections to the same ISP. Which BGP feature ensurestraffic is load balanced across the two links to the ISP?
A. Multihop
B. Multipath Load Sharing
C. Next-Hop Address Tracking
D. AS-Path Prepending
View answer
Correct Answer: B
Question #5
Topic 1Which two BGP features will result in successful route exchanges between eBGP neighbors sharing the same AS number?(Choose two.)
A. advertise-best-external
B. bestpath as-path ignore
C. client-to-client reflection
D. as-override
E. allow-as-in
View answer
Correct Answer: DE
Question #6
In a multicast network, which condition must be met for an RPF check to be performed on the RP address'?
A. he PIM DM device receives a multicast packet and has no directly connected members
B. he PIM router or multilayer switch has a shared-tree state
C. he PIM router or multilayer switch has a source-tree state
D. he PIM DM device receives a multicast packet and has no directly connected PIM neighbor
View answer
Correct Answer: B
Question #7
Topic 1What are two valid scaling techniques when an EIGRP network is designed that consists of more than 1000 routers?(Choose two.)
A. Use structured hierarchical topology with route summarization
B. Used sub-second timers
C. Use the distribute-list command to filter routes
D. Modify delay parameters on the links
E. Implement multiple EIGRP autonomous systems
View answer
Correct Answer: AE
Question #8
Assuming that preempt is not configured, when does a router in an HSRP group assume the role of the active router for the group?
A. A router in standby status will become the active router if it has a higher priority than the active router
B. A router in standby status will become the active router when it does not detect three consecutive hello messages from the active router
C. A router in standby status will become the active router when it does not detect any hello messages from the active router within the configured holdtime
D. A router in listening status will become the active router when it does not detect any hello messages from the active router within the configured holdtime
View answer
Correct Answer: C
Question #9
An engineer is designing a campus network with Cisco Catalyst 95CO switches in the aggression layer. The design requires running nonblocking Layer 2 MEC from the aggregation layer to the access layer. The Catalyst switches are located on different campus floors for availability reasons, and each access switch veil contam a single VLAN. Which technology must the engineer choose for the aggregation switches in the design?
A. PC
B. SS
C. tackWise Virtual
D. tackWise-180
View answer
Correct Answer: B
Question #10
Topic 1When a network is designed using IS-IS, which two circuit types are supported? (Choose two.)
A. nonbroadcast multiaccess
B. multiaccess
C. point-to-multipoint
D. nonbroadcast
E. point-to-point
View answer
Correct Answer: BE
Question #11
Topic 1A router running ISIS is showing high CPU and bandwidth utilization. An engineer discovers that the router is configured asL1/L2 and has L1 and L2 neighbors. Which step optimizes the design to address the issue?
A. Make this router a DIS for each of the interfaces
B. Disable the default behavior of advertising the default route on the L1/L2 router
C. Configure the router to be either L1 or L2
D. Configure each interface as either L1 or L2 circuit type
View answer
Correct Answer: D
Question #12
You have been assigned to create a plan to implement HSRP on the router connecting your company's network to the Internet. The router should be the active router in the HSRP group. On the active router, the following conditions should be met: Enable preemption with no delay Set Hello timer to 10 seconds and hold time to 25 seconds Set the priority to 150 Which of the following commands should be included in the plan to meet the given requirements? (Choose all that apply.)
A. standby 1 preempt delay minimum 10
B. standby 1 preempt
C. standby 1 priority 150
D. standby 1 timers 10 25
E. standby 1 timers 25 10
F. standby track interface S0/1
View answer
Correct Answer: BCD
Question #13
What command would be used to display detailed information regarding VRRP groups on the switch?
A. switch# show vrrp
B. switch# show standby
C. switch# show vrrp detail
D. switch# show standby detail
View answer
Correct Answer: A
Question #14
Which feature provides the capability for intra-VN traffic filtering and control within the Cisco SO-Access architecture?
A. calable groups
B. AC ACL
C. refix list
D. ervice policy
View answer
Correct Answer: A
Question #15
Topic 1Which method will filter routes between EIGRP neighbors within the same autonomous system?
A. distribute-list
B. policy-based routing
C. leak-map
D. route tagging
View answer
Correct Answer: A
Question #16
Topic 1Refer to the exhibit. EIGRP has been configured on all links. The spoke nodes have been configured as EIGRP stubs, andthe WAN links to R3 have higher bandwidth and lower delay than the WAN links to R4. When a link failure occurs at the R1-R2 link, what happens to traffic on R1 that is destined for a subnet attached to R2?
A. R1 has no route to R2 and drops the traffic
B. R1 load-balances across the paths through R3 and R4 to reach R2
C. R1 forwards the traffic to R3, but R3 drops the traffic
D. R1 forwards the traffic to R3 in order to reach R2
View answer
Correct Answer: D
Question #17
The partial output displayed in the exhibit is a result of what IOS command? (Click on the Exhibit(s) button.)
A. switch# show running-config
B. switch# show standby vlan1 active brief
C. switch# show hsrp 1
D. switch# show standby
View answer
Correct Answer: D
Question #18
Topic 1Which design consideration should be observed when EIGRP is configured on Data Center switches?
A. Perform manual summarization on all Layer 3 interfaces to minimize the size of the routing table
B. Prevent unnecessary EIGRP neighborships from forming across switch virtual interfaces
C. Lower EIGRP hello and hold timers to their minimum settings to ensure rapid route reconvergence
D. Configure multiple EIGRP autonomous systems to segment Data Center services and applications
View answer
Correct Answer: A
Question #19
How does a model-driven telemetry dial-out approach function?
A. he device initiates a session to the collector based on the subscription
B. he collector initiates a session to the device and subscribes to data to be streamed
C. he collector Initiates a session to the device and gets the data of a previously defined subscription
D. he device initiates a session to the collector and negotiates a subscription
View answer
Correct Answer: D
Question #20
Topic 1A customer with an IPv4 only network topology wants to enable IPv6 connectivity while preserving the IPv4 topologyservices. The customer plans to migrate IPv4 services to the IPv6 topology, then decommission the IPv4 topology. Whichtopology supports these requirements?
A. dual stack
B. 6VPE
C. 6to4
D. NAT64
View answer
Correct Answer: A
Question #21
Topic 1A company is using OSPF between its HQ location and a branch office. HQ is assigned area 0 and the branch office isassigned area 1. The company purchases a second branch office, but due to circuit delays to HQ, it decides to connect thenew branch office to the existing branch office as a temporary measure. The new branch office is assigned to area 2. WhichOSPF configuration enables all three locations to exchange routes?
A. The existing branch office must be configured as a stub area
B. A virtual link must be configured between the new branch office and HQ
C. A sham link must be configured between the new branch office and HQ
D. The new branch office must be configured as a stub area
View answer
Correct Answer: B
Question #22
What command disables 802.1x authentication on a port and permits traffic without authentication?
A. dot1x port-control disable
B. dot1x port-control force-unauthorized
C. dot1x port-control auto
D. dot1x port-control force-authorized
View answer
Correct Answer: D
Question #23
Which statement best describes the function of Hot Standby Router Protocol (HSRP)?
A. HSRP specifies a single IP address that all routers in the group must use
B. HSRP defines a set of routers that represent one virtual, fault-tolerant router
C. HSRP provides a round-robin gateway selection process to increase fault tolerance
D. HSRP defines a frame-tagging scheme that allows end stations to use any router as a gateway
View answer
Correct Answer: B
Question #24
Topic 1Refer to the exhibit. Which solution decreases the EIGRP convergence time?
A. Enable subsecond timers
B. Increase the hold time value
C. Increase the dead timer value
D. Enable stub routing on the spokes
View answer
Correct Answer: D
Question #25
Which command enables GLBP on an interface?
A. glbp
B. glbp 10 ip 192
C. standby mode glbp
D. switchport mode glbp
View answer
Correct Answer: B
Question #26
Topic 1Company A recently acquired another company. Users of the newly acquired company must be able to access a server thatexists on Company As network, both companies use overlapping IP address ranges. Which action conserves IP addressspace and provides access to the server?
A. Use a single IP address to create overload NAT
B. Use a single IP address to create a static NAT entry
C. Build one-to-one NAT translation for every user that needs access
D. Re-IP overlapping address space in the acquired company
View answer
Correct Answer: A
Question #27
Topic 1A network solution is being designed for a company that connects to multiple Internet service providers. Which Ciscoproprietary BGP path attribute will influence outbound traffic flow?
A. Local Preference
B. MED
C. Weight
D. AS Path
E. Community
View answer
Correct Answer: C
Question #28
Refer to the exhibit. Refer to the exhibit. An engineer Is designing a multicampus Layer 3 Infrastructure using EIGRP as the routing protocol. The design must provide quick replies to queries In the event of a downlink, prevent unnecessary queries, and ensure that traffic does not unnecessarily transit the access layer. Which two actions must the engineer take for the network design? (Choose two.)
A. onfigure core layer switches as stub routers
B. onfigure distribution layer switches to summarize routes to the core layer
C. onfigure access layer switches as stub routers
D. onfigure access layer and core layer switches as stub routers
E. onfigure access layer switches to summarize routes to the distribution layer
View answer
Correct Answer: BC

View Answers after Submission

Please submit your email and WhatsApp to get the answers of questions.

Note: Please make sure your email ID and Whatsapp are valid so that you can get the correct exam results.

Email:
Whatsapp/phone number:


Copyright © 2024. Designer by SPOTO Official Website. All Rights Reserved.