Optimize Your Juniper JN0-102 Exam Prep, Practice Tests, Juniper JNCIA-Junos Certification

Question #1

What is the default export routing policy for RIP?

A. Accept all local routes

B. Accept all RIP routes

C. Accept no routes

D. Accept all direct routes

View answer

Correct Answer: C

Question #2

A packet is evaluated against three user-defined terms within a firewall filter and no match is found. What correctly describes the action the firewall filter will take for this packet?

A. The filter will permit the packet and take no additional action

B. The filter will reject the packet and send an ICMP message back to the sender

C. The filter will discard the packet and take no additional action

D. The filter will permit the packet and write a log entry to the firewall log

View answer

Correct Answer: ACE

Question #3

-- Exhibit -- Exhibit -- You have been asked to establish reachability between Router 1's and Router 2's loopback addresses as shown in the exhibit. Real 123 Juniper JN0-102 Exam Which two steps will accomplish this task? (Choose two.)

A. Create a static route on Router 1 to 172

B. Create a static route on Router 1 to 172

C. Create a static route on Router 2 to 172

D. Create a static route on Router 1 to 172

View answer

Correct Answer: AC

Question #4

Which two characteristics describe the UDP protocol? (Choose two.)

A. limited error checking

B. defined timers

C. no recovery mechanisms

D. three-way handshake

View answer

Correct Answer: D

Question #5

-- Exhibit -- Real 132 Juniper JN0-102 Exam [edit policy-options] user@router# show policy-statementpolicyABC { term A { from { protocol rip; route-filter 192.168.1.0/24 longer; } then accept; } } [edit protocols ospf] user@router# show exportpolicyABC; area 0.0.0.0 { interface ge-0/0/0.0; interface lo0.0; } -- Exhibit -- Referring to the exhibit, which two statements are true? (Choose two.)

A. The route 192

B. The route 192

C. OSPF routes will be exported into RIP

D. RIP routes will be exported into OSPF

View answer

Correct Answer: D

Question #6

Which command will display the active configuration?

A. user@router> show configuration

B. user@router# show

C. user@router> show system configuration

D. user@router> show system commit

View answer

Correct Answer: C

Question #7

There are three static routes in the routing table that need to be announced to your OSPF peers. Which method is used to accomplish this?

A. Apply an import policy to OSPF that injects the static routes into OSPF

C. Apply an export policy to the static routes that injects the static routes into OSPF

D. Apply an export policy to OSPF that injects the static routes into OSPF

View answer

Correct Answer: A

Question #8

You must segment your internal /24 network into a minimum of 12 subnets, each containing a minimum of 12 hosts. Which network mask do you use?

A. /26 B

C. /28

D. /29

View answer

Correct Answer: CD

Question #9

You must apply the family inet configuration parameter only to Gigabit Ethernet interfaces that are in FPC 2. Which output applies to this configuration?

A. [edit groups]user@router# show ge-int {interfaces { {unit 0 {familyinet;}}}}

B. [edit groups]user@router# show ge-int {interfaces {<*> {unit 0 {familyinet;}}}}

C. [edit groups]user@router# show ge-int {interfaces {<*-2/*/*> {unit 0 {familyinet;}}}}

D. [edit groups]user@router# show ge-int {interfaces { {unit 0 {familyinet;}}}}

View answer

Correct Answer: AD

Question #10

What are two functions of the RE? (Choose two).

A. to maintain routing tables

B. to forward traffic toward its destination

C. to manage the PFE

D. to implement various services such as policing, stateless firewall filtering, and class of service

View answer

Correct Answer: A

Question #11

-- Exhibit -- user@router> show configuration firewall familyinet { filter demo { term example { from { source-address { 100.100.100.0/24; } destination-address { 200.200.200.0/24; } } then { reject; } } term testing { from { source-address { 10.10.10.0/28; } destination-address { 200.200.200.0/24; } Real 129 Juniper JN0-102 Exam } then sample; } term results { from { address { 200.200.200.0/24; } } then accept; } term final { thenpolicer LAPD; } } } -- Exhibit -- Given the configuration shown in the exhibi

A. The traffic will be rejected

B. The traffic will be dropped

C. The traffic will be forwarded

D. The traffic will be policed

View answer

Correct Answer: B

Question #12

What are the usable hosts on the .128.0/19 network?

A.

B.

C.

D.

View answer

Correct Answer: D

Question #13

What are three valid match criteria in a firewall filter applied to a Layer 3 interface? (Choose three.) A. IP address

B. MAC address

C. protocol

D. port

E. session ID

View answer

Correct Answer: A

Question #14

-- Exhibit -- user@router> show route protocol static inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 192.168.1.128/27 *[Static/5] 00:03:13 >to 10.20.106.10 via fe-0/0/5.1 192.168.1.144/29 *[Static/5] 00:03:13 >to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13 >to 10.18.1.1 via ge-0/0/1.0 192.168.1.128/28 *[Static/5] 00:01:06 >to 10.20.14.130 via ge-0/0/0.0 -- Exhibit -- Real 144 Juniper JN0-102 Exam Given the routing entrie

B. 10

C. 10

D. 10

View answer

Correct Answer: A

Question #15

-- Exhibit -- Exhibit -- Referring to the exhibit, you are asked to rate-limit traffic from Web-Server to the subnet where Mal-User is located. All other traffic should be permitted. Which firewall filter configuration do you use? Real 137 Juniper JN0-102 Exam

A. [edit firewall] user@router# show policer LIMIT-MAL-USER { if-exceeding { bandwidth-limit 400k; burst-size-limit 100k; } then discard; } familyinet { filter STOP-MAL-USER { term one { from { source-address { 100

B. [edit firewall] user@router# show policer LIMIT-BAD-USER { if-exceeding { bandwidth-limit 400k; burst-size-limit 100k; } then discard; } familyinet { filter STOP-MAL-USER { term one { from { source-address { 100

C. [edit firewall] user@router# show policer LIMIT-MAL-USER { if-exceeding { bandwidth-limit 400k; burst-size-limit 100k; } then discard; } familyinet { filter STOP-MAL-USER { term one { from { source-address { 100

D. [edit firewall] user@router# show policer LIMIT-MAL-USER { if-exceeding { bandwidth-limit 400k; burst-size-limit 100k; } then discard; } familyinet { filter STOP-MAL-USER { term one { from { Real 139 Juniper JN0-102 Exam source-address { 200

View answer

Correct Answer: C

Question #16

What is the default route preference value for EBGP? Real 92 Juniper JN0-102 Exam

A. 20

B. 100

C. 170

D. 200

View answer

Correct Answer: A

Question #17

-- Exhibit -- [edit routing-options] user@router# show static { defaults { metric 10; preference 10; } route 10.10.10.0/24 { next-hop 192.168.100.1; qualified-next-hop 192.168.200.1; preference 6; } metric 8; } } -- Exhibit -- Real 124 Juniper JN0-102 Exam Given the configuration shown in the exhibit, which statement is correct about traffic matching the route 10.10.10.0/24?

A. It will be forwarded to 192

B. It will be forwarded to 192

C. It will be forwarded to 192

View answer

Correct Answer: AC

Question #18

Which source of routing information is preferred by default?

A. OSPF internal

B. OSPF external

C. IS-IS Level 1

D. IS-IS Level 2

View answer

Correct Answer: BC

Question #19

What is the default protocol preference for OSPF internal routes? A. 10

B. 15

C. 150

D. 160

View answer

Correct Answer: D

Question #20

-- Exhibit -- user@router> show route inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 10.10.10.91/32 *[Direct/0] 00:09:40 >via lo0.0 10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1 >to 172.16.1.2 via ge-0/0/2.0 100.100.1.0/24 *[Static/5] 00:01:50 Reject 172.16.1.0/24 *[Direct/0] 00:06:09 >via ge-0/0/2.0 172.16.1.1/32 *[Local/0] 00:06:09 Local via ge-0/0/2.0 192.168.0.0/16 *[Aggregate/130] 00:00:06 Reject 192.168.0.0/17 *[Aggregate/130] 00:00:06 Real

A. 192

B. 192

C. 192

D. 192

View answer

Correct Answer: BCD

Question #21

Real 134 Juniper JN0-102 Exam -- Exhibit -- Exhibit -- Referring to the exhibit, you want to block HTTP access to Web-Server from the subnet where Mal-User is located. All other traffic should be permitted. Which firewall filter configuration do you use?

A. [edit firewall family inet filter STOP-MAL-USER] user@router# show term one { from { source-address { 200

B. [edit firewall family inet filter STOP-MAL-USER] user@router# show term one { from { source-address { 100

C. [edit firewall family inet filter STOP-MAL-USER] user@router# show term one { from { source-address { 100

D. [edit firewall family inet filter STOP-MAL-USER] user@router# show term one { from { source-address { 200

View answer

Correct Answer: D

Question #22

You have been assigned the /24 network and need to segment it into at least 60 subnets. Which network mask meets this requirement?

A. /27

B. /28

C. /29

D. /30

View answer

Correct Answer: AD

Question #23

What are three terminating actions for firewall filters? (Choose three.) Real 105 Juniper JN0-102 Exam

A. reject

B. drop

C. permit D

E. discard

View answer

Correct Answer: BCD

Question #24

At which command prompt would you issue the set date command? A. [edit chassis]user@router#

B. [edit]user@router#

C. [edit system]user@router#

D. user@router>

View answer

Correct Answer: B

Question #25

What is a route filter?

A. a list of prefixes that can be configured in a policy

B. a single prefix that is configured separately, and can be referenced in a policy

C. a list of prefixes that is configured separately and can be referenced in a policy

D. a single prefix that can be configured within a policy

View answer

Correct Answer: A

Question #26

-- Exhibit -- user@router# run show route /24 inet.0: 142 destinations, 142 routes (141 active, 0 holddown, 1 hidden) + = Active Route, - = Last Active, * = Both /24 *[OSPF/10] 04:10:20 Real 122 Juniper JN0-102 Exam >to 172.25.213.11 via ge-1/0/1.0 to 172.25.213.23 via ge-1/0/2.0 -- Exhibit -- In the exhibit, what does the (>) symbol indicate?

A. There is a software issue with ge-1/0/1

B. There is a hardware issue with ge-1/0/1

C. The next hop of 172

D. The next hop of 172

View answer

Correct Answer: CD

Question #27

Which three statements are true about terms in a policy? (Choose three.) A. The order of the terms in a policy is irrelevant.

B. The action is specified in a then statement

C. Terms are optional in a policy

D. The match condition can be identified with a from statement

E. A from statement is mandatory in a term

View answer

Correct Answer: CD

Question #28

Which two statements are true of a network mask? (Choose two.)

A. A subnet mask specifies the portion of an IP address that is in a binary format

B. A subnet mask specifies the portion of an IP address that is in a decimal format

D. A subnet mask specifies the portion of an IP address that represents network hosts

View answer

Correct Answer: D

Question #29

Which two statements are true regarding an Ethernet collision domain? (Choose two.)

A. If a switch is used, the collision domain is limited to each device and the switch

B. If a hub is used, the collision domain is limited to each device and the hub

C. If a hub is used, the collision domain includes all devices connected to the hub

D. If a switch is used, the collision domain includes all devices connected to the switch

View answer

Correct Answer: C

Question #30

What is the default export routing policy for EBGP? A. Accept all active BGP routes.

B. Accept all BGP routes

C. Accept no routes

D. Accept all active IGP routes

View answer

Correct Answer: A

Question #31

What represents the binary equivalence of 96?

A. 11010100

B. 01100000 C

D. 11101010

View answer

Correct Answer: C

Question #32

What information is used by a switch to forward an Ethernet frame to its destination?

A. IP address

B. destination MAC address

C. ARP table entry

D. FCS checksum

View answer

Correct Answer: ADE

Question #33

Which two statements are true about terms in a routing policy? (Choose two.)

A. A routing policy cannot have more than one term

B. If a term does not contain a from statement, all routes match

C. If a term does not contain a from statement, the Junos OS will not commit

D. A then statement is not mandatory in a term

View answer

Correct Answer: D

Question #34

Which two can be used to create and apply an export policy that advertises static routes to RIP neighbors? (Choose two.)

A. set protocols rip export demo

B. edit policy-options policy-statement demo set term 1 from protocol static set term 1 then accept

C. edit policy-options policy-statement demo set term 1 from protocol static accept

D. set protocols rip group internal export demo

View answer

Correct Answer: BD

Question #35

-- Exhibit -- [edit interfaces] user@router# show ... lo0 { unit 0 { familyinet { filter { input protect-loopback; } address 192.168.100.1/32; } } } -- Exhibit -- Given the configuration shown in the exhibit, what is the function of the protect-loopback filter?

A. to protect the Routing Engine

B. to protect all interfaces on the device

C. to protect the Packet Forwarding Engine

D. to protect the management interface

View answer

Correct Answer: C

Question #36

You are modifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value? (Choose Real 93 Juniper JN0-102 Exam two.)

A. local

B. OSPF

C. direct

D. BGP

View answer

Correct Answer: C

Question #37

What are two purposes of a forwarding class? (Choose two.)

A. to identify traffic that should be dropped

B. to classify traffic

C. to identify traffic that should receive common treatment

D. to assign traffic to output queues

View answer

Correct Answer: A

Question #38

What are two valid match criteria for a routing policy? (Choose two.)

A. OSPF area ID

B. prefix list

C. port

D. time-to-live (TTL) Real 104 Juniper JN0-102 Exam

View answer

Correct Answer: D

Question #39

Which two Junos platforms provide stateful firewall functionality? (Choose two.)

A. MX Series

B. EX Series

C. SRX Series

D. QFX Series

View answer

Correct Answer: A

Question #40

Which interface type connects the control and forwarding planes on an MX Series device?

A. fxp1

B. fxp0

C. me0

D. ae1

View answer

Correct Answer: BD

Question #41

-- Exhibit -- ... if-exceeding { bandwidth-limit 1m; burst-size-limit 3k; } then discard; -- Exhibit -- The configuration in the exhibit is associated with which class of service component?

A. classification

B. policing

C. queuing

D. scheduling

View answer

Correct Answer: A

Question #42

How many host addresses are available in the /28 network?

A. 6

B. 14

C. 28

D. 30

View answer

Correct Answer: C

Question #43

Which protocol creates a complete database of the network topology prior to calculating the optimal route?

A. BGP

B. PIM Real 98 Juniper JN0-102 Exam

C. OSPF

D. RIP

View answer

Correct Answer: BD

Question #44

-- Exhibit -- interfaces { ge-0/0/8 { Real 119 Juniper JN0-102 Exam unit 0 { family inet { address 192.168.1.1/24; } } } ge-0/0/9 { unit 0 { family inet { address 192.168.10.1/24; } } } } -- Exhibit -- Referring to the exhibit, which command would you use to add an additional address to the ge- 0/0/9.0 interface?

A. [edit interfaces ge-0/0/9 unit 0] user@router# set family inet address /24

B. [edit interfaces ge-0/0/9 unit 0] user@router# set family inet secondary-address /24

C. [edit interfaces ge-0/0/9 unit 0] user@router# set family inet address /24 secondary

D. [edit interfaces ge-0/0/9 unit 0] user@router# set family inet address-secondary /24

View answer

Correct Answer: C

Question #45

-- Exhibit -- user@router> show route protocol static inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 99.0.0.0/17 *[Static/5] 00:00:11 >to 10.1.1.2 via ge-0/0/1.0 99.0.0.0/19 *[Static/5] 00:00:11 >to 10.1.2.2 via ge-0/0/2.0 99.0.0.0/24 *[Static/5] 00:00:11 >to 10.1.3.2 via ge-0/0/3.0 99.0.0.0/26 *[Static/5] 00:00:11 >to 10.1.4.2 via ge-0/0/4.0 -- Exhibit -- In the exhibit, there are four static routes that route traffic through different inter

A. ge-0/0/1

B. ge-0/0/2

C. ge-0/0/3

D. ge-0/0/4

View answer

Correct Answer: D

Question #46

What are three benefits of using IPv6? (Choose three.)

A. IPv6 supports a greater level of security by integrating features that were optional add-ons in IPv4

B. IPv6 reduces administrative overhead using stateless address autoconfiguration for hosts

C. IPv6 eliminates the need for private to public NAT using a large address pool

D. IPv6 provides backward compatibility with IPv4 using the Next Header field

E. IPv6 represents large IP addresses using dotted decimal notation

View answer

Correct Answer: B

Question #47

Which two statements are correct about Layer 2 broadcast frames? (Choose two.) Real 111 Juniper JN0-102 Exam

A. Layer 2 broadcast frames are processed by all devices on the same VLAN

B. Layer 2 broadcast frames are discarded by routers that connect to multiple VLANs

C. Layer 2 broadcast frames are relayed by routers to all connected VLANs

D. Layer 2 broadcast frames are relayed by switches to devices on the same VLAN

View answer

Correct Answer: B

Question #48

You need to control SSH, HTTP, and Telnet access to an MX240 router through any interface. You have decided to use a firewall filter. How should you apply the firewall filter?

A. as an outbound filter on interface fxp0

B. as an outbound filter on interface lo0

C. as an inbound filter on interface fxp0

D. as an inbound filter on interface lo0

View answer

Correct Answer: D

Question #49

Two devices on an Ethernet segment sent frames at the same time causing a collision. Which two statements are true? (Choose two.)

A. Both devices stop transmitting, wait a random period of time, verify the wire is idle, and re- transmit

B. The device with the lowest MAC address is permitted to retransmit first

C. The device with the lowest MAC address sends a jam signal to notify all other devices of the collision

D. Both devices send a jam signal to notify all other devices of the collision

View answer

Correct Answer: CD

Question #50

Real 118 Juniper JN0-102 Exam -- Exhibit -- user@router# run show interfaces terse Interface Admin Link Proto Local fe-0/0/0 up up fe-0/0/0.0 up upinet 10.0.39.2/24 iso mpls fe-0/0/1 up up fe-0/0/1.0 up upinet 10.0.18.2/24 fe-0/0/1.5 down up inet 10.0.19.2/24 -- Exhibit -- An administrator is unable to ping any address on the 10.0.19.0/24 subnet. To identify the problem, the administrator uses the command shown in the exhibit. Which step should be taken to solve the problem?

A. Check the physical cable

B. Issue the command activate interfaces fe-0/0/1

C. Issue the command delete interfaces fe-0/0/1

D. Reconfigure the IP address

View answer

Correct Answer: AD

Question #51

By default, if equal-cost paths exist for the same destination, which action will the router take?

A. Drop half the traffic

B. Make a copy of the traffic and send it to both destinations

D. Randomly select one of the available paths to send traffic

View answer

Correct Answer: D

Question #52

-- Exhibit -- user@router> show route protocol static inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 192.168.1.0/24 *[Static/5] 00:03:13 >to 10.20.106.10 via fe-0/0/5.1 192.168.1.192/26 *[Static/5] 00:03:13 >to 10.20.14.131 via ge-0/0/0.0 192.168.1.192/27 *[Static/5] 00:03:13 >to 10.18.1.1 via ge-0/0/1.0 192.168.1.4/30 *[Static/5] 00:01:06 >to 10.20.14.130 via ge-0/0/0.0 -- Exhibit -- Using the routing table shown in the exhibit, what will be

A. 10

B. 10

C. 10

D. 10

View answer

Correct Answer: B

Question #53

Which two statements are true regarding rescue configurations? (Choose two.) A. Once saved, a rescue configuration is loaded using the rollback 0 command.

B. The rescue configuration must contain the minimal elements necessary to restore network connectivity

C. A minimal rescue configuration is defined by default

D. A rescue configuration must include a root password

View answer

Correct Answer: ABE

Question #54

You have been asked to configure your MX240 with a default route toward your upstream ISP at IP address 192.168.100.1. Which command successfully completes this task? A. user@router# set routing-options static route 0.0.0.0/0 next-hop 192.168.100.1

B. user@router# set routing-options default route 0

C. user@router# set forwarding-options static route 0

D. user@router# set protocols default route 0

View answer

Correct Answer: A

Question #55

What is the decimal equivalent of 10101010? Real 110 Juniper JN0-102 Exam A. 182

B. 180

C. 172

D. 170

View answer

Correct Answer: C

Question #56

What represents the decimal equivalence of 11100101? Real 109 Juniper JN0-102 Exam

A. 5

B. 93

C. 177

D. 229

View answer

Correct Answer: BC

Question #57

What is a valid multicast MAC address? Real 112 Juniper JN0-102 Exam

A. 00:90:69:9f:ea:46

B. ff:ff:ff:ff:ff:ff

C. 01:00:5e:28:12:95

D. 99:99:99:99:99:99

View answer

Correct Answer: D

Question #58

What is the binary equivalent of 242.168.94.124?

A. 11110011 10101000 01011110 01111100

B. 11110010 10101010 01011110 01111100

C. 11110010 10101000 01011110 01111100

D. 11110010 10101000 01010110 01111100

View answer

Correct Answer: A

Question #59

-- Exhibit -- [editsnmp] user@router# show communityCommunityA { authorization read-only; clients { 192.168.1.0/28; } } trap-groupgroupA { categories { link; } targets { 192.168.100.1; 192.168.200.1; } } -- Exhibit -- Referring to the exhibit, what is the purpose of the targets section of the configuration? A. It defines which devices will be sending traps.

B. It specifies where to send traps

C. It defines the IP addresses of management systems that can access the device

D. It specifies which devices can be polled for SNMP data

View answer

Correct Answer: C

Question #60

Which command will display only direct routes?

A. show route

B. show route inet

C. show ip route direct

D. show route protocol direct

View answer

Correct Answer: C

Question #61

Which statement is true regarding an Ethernet collision domain?

A. If a router is used, the collision domain includes all devices connected to the router

B. If a hub is used, the collision domain is limited to each device and the hub

C. If a switch is used, the collision domain is limited to each device and the switch

D. If a bridge is used, the collision domain includes all devices connected to the bridge

View answer

Correct Answer: A

Question #62

What are two reasons why a route might be hidden? (Choose two.) Real 94 Juniper JN0-102 Exam

A. route preference

B. routing loop

C. invalid next hop

D. routing policy

View answer

Correct Answer: AD

Question #63

Which statement describes an advantage of dynamic routing?

A. Dynamic routing provides redundant IP addresses for end-user devices, unlike static routing

B. Dynamic routing requires no initial user configuration, unlike static routing

C. Dynamic routing provides DNS services along with IP connectivity; static routing does not

D. Dynamic routing typically requires less time to implement than static routing in a large network

View answer

Correct Answer: CD

Question #64

-- Exhibit -- [edit class-of-service] user@router# show interfaces { ge-0/0/2 { unit 0 { classifiers { inet-precedence default; Real 142 Juniper JN0-102 Exam } } } } -- Exhibit -- Referring to the exhibit, which type of classifier is being used in this CoS configuration?

A. behavior aggregate

B. policer

C. multifield

D. forwarding policy

View answer

Correct Answer: C

Question #65

Which network mask is the equivalent of 255.255.248.0? A. /20

B. /21

C. /22

D. /23

View answer

Correct Answer: BD

Question #66

-- Exhibit -- user@router> show route inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 10.10.10.91/32 *[Direct/0] 00:09:40 >via lo0.0 10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1 >to 172.16.1.2 via ge-0/0/2.0 100.100.1.0/24 *[Static/5] 00:01:50 Reject 172.16.1.0/24 *[Direct/0] 00:06:09 >via ge-0/0/2.0 172.16.1.1/32 *[Local/0] 00:06:09 Local via ge-0/0/2.0 192.168.0.0/16 *[Aggregate/130] 00:00:06 Reject 192.168.0.0/17 *[Aggregate/130] 00:00:06 >to

A. 192

B. 192

C. 192

D. 192

View answer

Correct Answer: CD

Question #67

You have received a default route through BGP from your ISP and you want to redistribute it into OSPF. Which method will accomplish this?

A. Apply an export policy to OSPF that exports the default route

B. Apply an import policy to OSPF that imports the default route

C. Apply the default-network command to OSPF

D. Apply the redistribute-igp command to BGP

View answer

Correct Answer: A

Question #68

To which directory does the Junos OS write traceoptions files?

A. /var/tmp/

B. /var/ C

D. /var/home//

View answer

Correct Answer: D

Question #69

What represents the binary equivalence of 207? Real 108 Juniper JN0-102 Exam

A. 11001111

B. 11101011

C. 11010111

D. 11010101

View answer

Correct Answer: D

Question #70

Which configuration causes RIP-learned routes to be advertised to other RIP neighbors?

A. set protocol rip no-passive

B. top edit policy-options policy-statement demo set term 1 from protocol rip set term 1 then accept top set protocols rip group internal export demo

C. set protocols rip advertise in-out

D. top edit policy-options policy-statement demo set term 1 from active routes set term 1 then accept top set protocols rip group internal export demo Real 106 Juniper JN0-102 Exam

View answer

Correct Answer: D

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now

Optimize Your Juniper JN0-102 Exam Prep, Practice Tests, Juniper JNCIA-Junos Certification | SPOTO

View The Updated JN0-102 Exam Questions

View The Updated Juniper Exam Questions

View Answers after Submission

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE! Get Now

Optimize Your Juniper JN0-102 Exam Prep, Practice Tests, Juniper JNCIA-Junos Certification | SPOTO

View The Updated JN0-102 Exam Questions

View The Updated Juniper Exam Questions

View Answers after Submission

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now