Free HP HPE7-A07 Practice Questions & Answers 2026 Part3 | Aruba Certified

A network administrator accesses HPE Aruba Networking Central and notices that visitors consume too much internet bandwidth, starving employee traffic when accessing an external service. Therefore, the administrator wants to limit wireless bandwidth to 50 Mbps in both directions among all users in the voice role and no more than 10 Mbps in both directions for YouTube traffic. Deep packet inspection, web content classification, and firewall visibility are enabled.Which configurations are required to accomplish this task? (Choose two.)

Which option shows the correct Banawidth Control for 1024 kbps down and 2048 Kops up for the SSID?

Your customer asked for help to apply an ACL for wireless guest users with the following criteria:• Wi-Fi guests are on VLAN 555• allow internet access• only allow access to public DNS servers• deny access to all internal networks except for any DHCP serverThese session ACLs are already present in the CLI of the mobility gateway group:You have access to the CLl. Which user role meets all the criteria?A)B)C)D)

A client connecting to a tunneled open network is receiving the wrong VLAN Your customer has a gateway and has sent over a packet capture from a switch port mirror taken from the upstream switch with a packet capture from the IPsec tunnel and the GRE tunnel to help Identify the VLAN being sent from the controller to the AP.

A customer is deploying a new warehouse with AP-634 APs in the united States with mobile devices that can operate in the 6GHz spectrum All testing and RF analyses were performed during the POC using AP-635 APs In a different location During the deployment, they noticed fewer 6GHz channels were broadcasting in the air.Why would the AP-634 deployment have a lesser amount of broadcasting channels?

You want to configure an MTU of 9198 for a routed lag interface on a CX 6300 switch. Which configuration achieves this?

A customer reports that their HPE Aruba Networking ClearPass Guest captive portal is not functioning. The page loads but they are unable to browse after pressing connect. They have uploaded a valid and publicly trusted *.aruba-training.com certificate.Refer to the exhibit.Which would explain this issue?

You configured a WPA3-SAE with the following MAC Authentication Role Mapping in Cloud Authentication and Policy: With further default settings assume a new Android phone is connected to the network. Which role will the client be assigned after connecting for the first time? The configuration shown in the third exhibit details a client role mapping that associates different client profile tags with specific client roles. When a new device, such as an Android phone, connects to the network, it will be profiled and assigned a role based on the mappings defined. If the device does not match any predefined profiles, it would be assigned the 'unmatched-device' role. This is under the assumption that default settings are in place and the client does not match the criteria for any of the specific roles like 'byod', 'iot-internet', or 'iot-local'. Therefore, an Android phone connecting for the first time and not matching any specific profile tag would be assigned to the 'unmatched-device' role.

An OSPF router has learned a pain 10 an external network by Doth an E1 and an E2 advertisement Both routes have the same path cost Which path will the router prefer?

A customer deployed AP-535s for IoT devices that send many small packets. They want to reduce congestion and allow simultaneous transmission to or from multiple users.

Which command would allow you to verity receipt of a CoA message on an AOS 10 GW?

You configured" a bridgedmode SSID with WPA3-Enterprise and EAP-TLS security. When you connect an Active Directory joined client that has valid client certificates. ClearPass shows the following error.

What directly affects the MCS used by wireless stations? (Select two.)

Your customer added third-party USB dongles to the USB ports of their AOS 10 access points. The customer uses AP-615 and AP-635 Each AP is connected with a Cat 6A cable to a CX 6300F Class 4 PoE switch All APs are in the same group in HPE Aruba Networking Central and share the same configuration However, many of the dongles do not come up.

You are testing the use of the automated port - access role configuration process using RadSec authentication over VXLAN. During your testing you observed that the RadSec connection will fan during the digital certificate exchange What would be the cause of this Issue?

A university owns a campus with several buildings segmented into east and west wings, which are L3 separated. The east wing has 1600 APs. and the west wing has 1200 Aps. Each wing has a single gateway cluster managed by HPE Aruba Networking Central. Each cluster contains one 7210 mobility gateway The gateways are configured with DHCP relay and route all client VLANs. A new business- critical faculty real-time application requires users to roam within wings but not across wings without disconnections or delay increments.Which changes must the network administrator make lo successfully meet the requirement without performance degradation matching best practices? (Select two.)

Refer to the CLI output below:What statement about the output above is correct?

A customer has deployed an AOS-10 mobility gateway cluster consisting of three controllers at a single site. The WLAN is configured to tunnel wireless device traffic to the AOS-10 mobility cluster. The clients are authorized to use WPA2-Personal. An end-user has opened a ticket with the helpdesk stating they cannot connect their client device to the network. There are other devices currently associated with the SSID with no issues.Reviewing the output, what is the issue?

A campus topology uses VSX with a collapsed core topology. The customer added redundant SFP+ transceivers and reconfigured their mobility gateways from a single link to an aggregate link. You are asked to verify the CLI output for the link aggregation configuration for one of the mobility gateway cluster members below.What is a valid configuration?

Exhibit.

Which statement is true given the following CLI output from a CX 6300?

You are testing the use of the automated port-access role configuration process using RadSec authentication over VXLAN. During your testing you observed that the RadSec connection will fan during the digital certificate exchange What would be the cause of this Issue? During the testing of RadSec authentication over VXLAN, if the RadSec connection fails during the digital certificate exchange, it typically indicates an issue with the establishment of the TLS tunnel, which is required for RadSec's secure communication. The failure of TLS tunnel establishment can occur due to RADIUS TCP packets being dropped, preventing the secure exchange of digital certificates necessary for RadSec authentication. The other options, such as IPv6 address reachability, tracking mode settings, and proxy server misconfiguration, are not directly related to the failure of the TLS tunnel establishment during the certificate exchange process

A campus topology uses VSX with a collapsed core topology. The customer added redundant SFP+ transceivers and reconfigured their mobility gateways from a single link to an aggregate Link. You are asked to verify the CLI output for the link aggregation configuration for one of the mobility gateway cluster members below. What is a valid configuration? A) B) C) D)