Prepare Strategically for the Cisco 350-601 DCCOR Exam with Practice Tests

Question #1

Refer to the exhibit.Which statement about the default gateway configuration of the vPC is true?

A. ither switch can act as the active default gateway

B. 7K-1 acts as the default gateway for all traffic

C. 7K-2 forwards traffic that is destined for the default gateway by using the peer link

D. 7K-2 acts as the default gateway for all traffic

View answer

Correct Answer: A

Question #2

A network architect considers a Cisco HyperFlex design solution for a company. The proposed solution is for a virtual environment that is not performance-sensitive, but the solution must have high storage capacity and a low cost. Which Cisco HyperFlex storage configuration should be used?

A. ybrid

B. ll-SAN

C. ll-NVMe

D. ll-Flash

View answer

Correct Answer: A

Question #3

An engineer must implement a disaster recovery policy for the Cisco UCS infrastructure. The solution must meet these criteria:-The Recovery Point Objective must be 48 hours.-The backup must use encrypted transmission.-The Recovery Time Objective must be 4 hours.Which configuration set must be used in the scheduled backup to meet these requirements?

A. rotocol: FTPSchedule: Bi-Weekly

B. rotocol: SFTPSchedule: Weekly

C. rotocol: TFTPSchedule: Bi-Weekly

D. rotocol: SCPSchedule: Daily

View answer

Correct Answer: D

Question #4

A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. Which action should be taken to implement the same action on Nexus switches?

A. se the alias command to use the write memory command

B. se the wri command to use the copy running-config startup-config command

C. se the exit command to leave the configuration mode and save the configuration automatically

D. se the write memory command to save the configuration

View answer

Correct Answer: A

Question #5

Multiple roles are applied to a user on the Cisco MDS 9000 Series Switch. Which statement describes the result of this configuration?

A. he last role assigned takes precedence over previous roles

B. ccess to a command takes priority over being denied access to a command

C. ny commands that have conflicting settings between roles are denied

D. he first role assigned takes precedence over subsequent roles

View answer

Correct Answer: B

Question #6

Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development. Which attribute must be used to assign the servers to different microsegments?

A. rc-id/dst-id

B. rc-dst-oui

C. rc-dst-port

D. rc-id/dst-id/oxid

View answer

Correct Answer: B

Question #7

What is an advantage of streaming telemetry over SNMP?

A. f "On demand" is selected, the policy is programmed in the hardware only when the first packet is received through the data path

B. t "Immediate" is selected, the policy is programmed in the hardware as soon as the leaf is booted

C. he "Immediate" and "On demand" options require a port group to be created on the VDS

D. f "On demand" is selected, the policy is programmed in the hardware only when the APIC detects a VM created in the EPG

View answer

Correct Answer: B

Question #8

A DNS server with IP address 192.168.1.1 is deployed in a data center. A network engineer must configure a Cisco UCS Fabric Interconnect to use this DNS. Which configuration should be applied?

A. icl-mgmt-A# scope fabric-interconnect aficl-mgmt-A /fabric-interconnect # set name 192

B. icl-mgmt-A# scope systemficl-mgmt-A /system # create dns 192

C. icl-mgmt-A# scope fabric-interconnect aficl-mgmt-A /fabric-interconnect # set name 192

D. icl-mgmt-A# scope systemficl-mgmt-A /system # scope servicesficl-mgmt-A /system/services # create dns 192

View answer

Correct Answer: D

Question #9

Refer to the exhibit. Which VLANs are capable to be assigned on vPC interfaces?

A. 00-102

B. 00-103

C. 00-104

D. 00-105

View answer

Correct Answer: D

Question #10

An engineer must perform an initial configuration of VXLAN Tunnel End-Point functionality on the Cisco Nexus 9000 Series platform. All the necessary features are already enabled on the switch. Which configuration set must be used to accomplish this goal?

A. X9K(config)# interface loopback0 NX9K(config-if)# ip address 10

B. X9K(config)# interface loopback0 NX9K(config-if)# ip address 10

C. X9K(config)# interface loopback0 NX9K(config-if)# ip address 10

D. X9K(config)# interface loopback0 NX9K(config-if)# ip address 10

View answer

Correct Answer: D

Question #11

A customer needs a tool to take advantage of the CI/CD model to streamline its operations and optimize cost. The customer wants to integrate the solution with the Cisco products it currently uses, including Cisco ACI networking and Cisco UCS Series servers. The solution should also provide on-premises Kubernetes and AppDynamics performance monitoring. Because of the security requirements, the solution should not install a local client on products under management. Which orchestration solution meets these re

A. isco UCS Director

B. isco CloudCenter

C. isco APIC

D. isco DCNM

View answer

Correct Answer: B

Question #12

A Cisco ACI engineer must configure an access port on a Cisco ACI leaf switch. The access policy should be configured so that it supports L3Out connectivity concurrently with several EPGs that are mapped to this interface with the static port method. How should the access policy be configured?

A. y linking the interface policy group to multiple Attachable Access Entity Profiles

B. ith two interface policy groups that are linked to the same interface profile port selector

C. y mapping a single physical domain, mapped to the L3out and EPG interfaces

D. ith a single Attachable Access Entity Profile that is linked to the corresponding routed domain and physical domain

View answer

Correct Answer: A

Question #13

Refer to the exhibit.What is the result of this series of commands?

A. t reboots the server immediately

B. t activates the firmware on the next adapter boot

C. t updates the firmware on adapter 1/1/1 immediately

D. t verifies the firmware update on the server

View answer

Correct Answer: B

Question #14

Which product includes prebuilt templates that are available to be used to customize fabric deployments?

A. isco Tetration

B. isco Data Center Network Manager

C. isco ACI

D. isco UCS Manager

View answer

Correct Answer: B

Question #15

An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?

A. he system defaults to and boots into kickstart image

B. he system defaults to and boots into GOLD firmware image

C. he system defaults to the GOLD firmware image

D. he system defaults to the backup image version

View answer

Correct Answer: D

Question #16

Which component is disrupted when the Cisco Integrated Management Controller is upgraded on a Cisco UCS Series Server?

A. AN traffic

B. isco UCS Manager

C. VM sessions

D. ata traffic

View answer

Correct Answer: B

Question #17

An engineer installed a new Nexus switch with the mgm0 interface in vrf management. Connectivity to the rest of the network needs to be tested from the guest shell of the NX-OS. Which command tests connectivity from the guest shell of the NX-OS?

A. guestshell@guestshell ~]$ dohost ''ping vrf management 173

B. guestshell@guestshell ~]$ chvrf management ping 173

C. guestshell@guestshell ~$ ping 173

D. guestshell@guestshell ~]$ iping vrf management ip 173

View answer

Correct Answer: B

Question #18

An engineer must perform a software upgrade on a production Cisco Nexus 7000 Series Switch. Before the upgrade activity, the requirement is for all ports to be shut down and routing protocols to terminate gracefully. Which feature must be used to meet these requirements?

A. witch Profile

B. ervice Profile Template

C. aintenance Mode Profile

D. onfiguration Profile

View answer

Correct Answer: C

Question #19

Refer to the exhibit. During a vPC peer switch reload, there is packet loss between the server and the router. Which action must be taken to prevent this behavior during future reloads?

A. et the routed uplink ports of the Cisco Nexus peers as orphans

B. ncrease the vPC delay restore timer

C. isable vPC ARP synchronize on the vPC peers

D. ecrease the OSPF hello and dead interval timers

View answer

Correct Answer: B

Question #20

An engineer is implementing FCoE.Which aspect of DCBXP on a Cisco Nexus switch affects this implementation?

A. t requires that LLDP transmit and LLDP receive are enabled on the FCoE interface

B. t uses the Cisco Fabric Services protocol to exchange parameters between two peer links

C. t provides the authentication of peers on the Cisco Nexus switch

D. t always is enabled on 10/100-Mbps native Ethernet ports

View answer

Correct Answer: A

Question #21

Refer to the exhibit. What happens to the broadcast traffic when it reaches aggregation switches?

A. gg-2 switch receives broadcast packets and stops forwarding to the peer link on Agg-1 switch

B. gg-1 switch prevents broadcast packets received on the vPC peer link from exiting the switch on ports Eth2/4 and Eth2/5

C. gg-1 and Agg-2 switches receive broadcast packets and does not forward them to the peer link or the port channel

D. nly Agg-1 switch receives broadcast packets and does not forward to the peer link on Agg-2 switch

View answer

Correct Answer: A

Question #22

An engineer creates a service profile in Cisco UCS Manager and must assign a policy that reboots blades when changes are applied. The changes must be applied only after user acknowledgment. Which two policies must be configured to meet these requirements? (Choose two.)

A. dapter

B. isco IMC

C. /O Modules

D. IOS

View answer

Correct Answer: AE

Question #23

Which two statements describe the process of performing an EPLD upgrade on a Cisco MDS 9000 Series Switch? (Choose two.)

A. isplays the compatibility of the EPLD upgrade and the image in the bootflash

B. hows a simulated upgrade of the EPLD

C. pgrades the EPLD on the switch disruptively

D. isplays the impact of the upgrade on the operation of the switch

View answer

Correct Answer: AB

Question #24

Which action must be performed before renumbering a Cisco UCS chassis?

A. un the shut and no shut command on the connected ports

B. ove the chassis to new ports on fabric interconnect

C. ecommission the chassis

D. e-acknowledge the chassis

View answer

Correct Answer: C

Question #25

An engineer needs to perform a backup of user roles and locales from Cisco UCS Manager to replicate the setting to a different fabric interconnect. The engineer wants to review the file before importing it to a target fabric interconnect. Which backup type must be selected to meet these requirements?

A. ogical configuration

B. ull state

C. ystem configuration

D. ll configuration

View answer

Correct Answer: C

Question #26

An engineer is asked to use SaaS to manage Cisco computing. Which two items are needed to accomplish the task? (Choose two.)

A. ystems

B. oles

C. ervers

D. ervice profiles

View answer

Correct Answer: AE

Question #27

An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #28

An engineer needs to make an XML backup of Cisco UCS Manager. The backup should be transferred using an authenticated and encrypted tunnel, and it should contain all system and service profiles configuration.Which command must be implemented to meet these requirements?

A. opy running-config scp://user@host35/backups/all-config9

B. reate backup scp://user@host35/backups/all-config9

C. reate file scp://user@host35/backups/all-config9

D. opy startup-config scp://user@host35/backups/all-config9

View answer

Correct Answer: A

Question #29

A small remote office is set to connect to the regional hub site via NSSA ASBR. Which type of LSA is sent to the remote office OSPF area?

A. ype 7 LSA

B. ype 1 LSA

C. ype 5 LSA

D. ype 3 LSA

View answer

Correct Answer: A

Question #30

A customer has a requirement to deploy a cloud service and needs to have full control over the underlying OS, data and applications.Which cloud model meets this requirement?

A. aaS

B. aaS

C. aaS

D. aaS

View answer

Correct Answer: D

Question #31

The VMM domain is integrated between Cisco APICs and vCenter using a distributed vSwitch. The traffic must be blocked between a subset of endpoints in an EPG based on specific VM attributes and the rest of the VMs in that EPG. Which set of actions blocks this traffic?

A.

B.

C.

D.

View answer

Correct Answer: C

Question #32

What is a benefit of independent resource scaling in Cisco HyperFlex hybrid architecture?

A. emote booting of converged servers

B. lexible expansion of compute, caching, and capacity

C. ultivendor converged node hardware support

D. upport for compute nodes with third-party storage

View answer

Correct Answer: B

Question #33

What is the benefit of adding Cisco HyperFlex Hardware Acceleration Cards to a HyperFlex deployment?

A. ncreased compression efficiency

B. ncreased network throughput

C. PU acceleration

D. ffline encryption acceleration

View answer

Correct Answer: A

Question #34

An engineer is configuring VNTag between a virtualized server and a Cisco Nexus 5500 Series switch. Drag and drop the configuration steps from the left into the correct order on the right.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #35

An engineer changed a configuration and must perform a rollback. Which statement applies to a Cisco Nexus 5600 Series Switch?

A. he standby supervisor module is capable of performing the upgrade

B. nly the modules that are being upgraded are disrupted

C. ll modules on the switch are disrupted

D. n EPLD upgrade is nondisruptive

View answer

Correct Answer: A

Question #36

An engineer deploys a custom guest shell rootfs onto multiple switches. Drag and drop the steps from the left into the correct order on the right. Export the Guest Shell rootfs.Select and Place:

A. he configuration rollback functionality is disabled when FCoE is enabled

B. system checkpoint is generated automatically when the running configuration is saved to NVRAM

C. user who is assigned to the network-operator user role is allowed to perform a rollback

D. rrors are skipped when an atomic rollback type is triggered

View answer

Correct Answer: A

Question #37

Refer to the exhibit.What is configured as a result of running these commands?

A. oose unicast RPF

B. trict unicast RPF

C. P Source Guard

D. everse lookup for outbound packets

View answer

Correct Answer: B

Question #38

Drag and drop the network assurance concepts from the left onto the corresponding benefits on the right.

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #39

A Cisco Nexus 9000 Series Switch experiences a startup configuration corruption. The engineer must implement a procedure to recover the backup configuration file from the switch. Which command set must be used?

A. et default VLAN on the adapters

B. ncrease CoS to 6

C. nable Uplink Failover

D. isable VNTAG mode

View answer

Correct Answer: C

Question #40

Refer to the exhibit. In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two Cisco NX-OS routers have these requirements:-R1 must be the active RP.-R2 must be the backup RP that is used only if R1 is not reachable.Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #41

A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containerized applications. The operations team requires a solution to orchestrate and optimize the cost of the new solution. Which product must be used to meet these requirements?

A. isco Workload Optimization Manager

B. isco CloudCenter

C. isco Intersight

D. isco Data Center Network Manager

View answer

Correct Answer: B

Question #42

A server engineer wants to control power usage on a Cisco UCS C-Series rack server down to the component level.Which two components support specific power limits? (Choose two.)

A. nformation is modified on the management plane only

B. configuration is imported from a higher release to a lower release

C. t is possible to schedule an import operation

D. nly a configuration file that was exported from the same Cisco UCS Manager is allowed to be imported

View answer

Correct Answer: AB

Question #43

What occurs when running the command install deactivate while a software maintenance upgrade is performed on a Cisco Nexus 9000 Series switch?

A. he current set of packages is committed

B. he package features for the line card are disabled

C. he package is removed from the switch

D. he current upgrade stops

View answer

Correct Answer: B

Question #44

An engineer must configure HSPR protocol on two Cisco Nexus 9000 Series Switches running a virtual port channel. In addition, the HSRP implementation must meet these requirements: -It must allow more than 500 groups.-switch1 must act as the primary switch.-Both switches must use a user-defined hardware address.Drag and drop the commands from the right to complete a configuration of the HSRP on the left. The commands are used more than once. Not all commands are used.

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #45

Refer to the exhibit. Software downgrade is required on a Cisco Nexus 7000 Series Switch. What is displayed when this command is executed?

A. eatures that are enabled automatically after the downgrade

B. mpact of a software upgrade in ISSU and chassis reload

C. eatures and commands that are removed automatically from the configuration

D. ompatibility of software in the system bootflash file

View answer

Correct Answer: B

Question #46

What are two types of FC/FCoE oversubscription ratios? (Choose two.)

A. ones are local to the MDS switch and name service must be used to activate the connection between E Ports

B. ifferent zone set names must be configured on both MDS switches

C. ones must have the same name on both MDS switches for the E Ports to function

D. Ports on both MDS switches must be configured as F Ports for the zoning to function

View answer

Correct Answer: DE

Question #47

Which server policy is used to install new Cisco IMC software on a server?

A. ypervisor firmware policy

B. ost firmware policy

C. IOS software policy

D. isco IMC software policy

View answer

Correct Answer: D

Question #48

Which two hypervisors does Cisco HyperFlex support? (Choose two.)

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: CE

Question #49

An engineer implements an ACI fabric and must implement microsegmentation of endpoints within the same IP subnet using a network-based attribute. The attribute mapping must allow IP subnet independence. Which attribute must be selected?

A. P

B. ag

C. ustom

D. AC address

View answer

Correct Answer: D

Question #50

Refer to the exhibit. An engineer needs to implement a monitoring session that should meet the following requirements:-Monitor traffic from leaf to leaf switches on a Cisco ACI network -Support filtering traffic from Bridge Domain or VRFWhich configuration must be added to meet these requirements?

A. nterface eth 1/2 leaf 101

B. pplication epg epg1 app1

C. nterface eth 1/2 switch 101

D. pplication app1 epg epg1

View answer

Correct Answer: D

Question #51

A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus Series switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted. Which set of steps must be taken to meet these requirements?

A.

B.

C.

D.

View answer

Correct Answer: B

Question #52

Drag and drop the fields for configuring a full state backup file of the Cisco UCS Manager from the left onto the descriptions on the right.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #53

Which feature is supported with an In-Service Software Upgrade on a Cisco Nexus 9000 Series Switch?

A. ondisruptive upgrades via nonstop forwarding

B. onfiguration changes during an upgrade

C. pgrades to individual modules and line cards

D. ero downtime downgrades via dual supervisor modules

View answer

Correct Answer: D

Question #54

Refer to the exhibit.Which result of running the command is true?

A. he VRRP process crashed and the checkpoint was automatically created

B. he VRRP service restarted and the checkpoint was automatically created

C. he network administrator manually created it

D. he VRRP-enabled feature has been disabled

View answer

Correct Answer: C

Question #55

Which statement describes the MAC address that the FCoE Initialization Protocol chooses for use by an E- Node in an FCoE implementation?

A. he FCoE Initialization Protocol uses a 24-bit FC-MAP and concatenates a 24-bit Fibre Channel ID to create a fabric-provided MAC address

B. he FCoE Initialization Protocol uses the burned-in MAC address of the converged network adapter for all FCoE operations

C. CoE does not use a MAC address

D. he FCoE Initialization Protocol uses 01

View answer

Correct Answer: A

Question #56

An engineer must configure the order in which the server attempts to boot from available boot device types using Cisco Integrated Management Controller (Cisco IMC). The engineer must change the boot order configuration during the setup and apply the new requirements multiple times. The requirement is to change the Cisco IMC actual boot order so it is different from the configured boot order. Which setting accomplishes this goal?

A. nable the system to boot with the configured boot order

B. et the boot configuration directly through BIOS

C. pply UEFI Secure Boot for a nonsupported operating system

D. onfigure the legacy and precision boot order to be mutually exclusive

View answer

Correct Answer: B

Question #57

A network engineer is asked to describe the cloud infrastructure models from the perspective of their operation and access to resources. Drag and drop the descriptions from the left onto the appropriate characteristics on the right.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #58

A network architect must redesign a data center network based on OSPFv2. The network must perform fast reconvergence between directly connected switches. Which two actions must be taken to meet the requirements? (Choose two.)

A. 7K_A(config-vpc-domain)# role priority 1N7K_B(config-vpc-domain )# role priority 2

B. 7K_A(config-vpc-domain)# system-priority 32768N7K_B(config-vpc-domain)# system-priority 32768

C. 7K_A(config-vpc-domain)# system-priority 100N7K_B(config-vpc-domain)# system-priority 200

D. 7K_A(config-vpc-domain)# system-priority 4000N7K_B(config-vpc-domain)# system-priority 4000

View answer

Correct Answer: CD

Question #59

Where is the witness deployed in a two-node Cisco HyperFlex Edge deployment?

A. o the HyperFlex Edge two-node cluster

B. o Cisco Intersight

C. o a third-party cloud provider

D. o an additional server with network access to HyperFlex Edge

View answer

Correct Answer: B

Question #60

APIC EPG Resolution Immediacy is set to "Immediate".Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?

A. W2# configure terminalSW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 255

B. W2# configure terminalSW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 1

C. W2# configure terminal SW2 (config)# router ospf 1SW2 (config-router)# router-id 10

D. W2# configure terminalSW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 0

View answer

Correct Answer: A

Question #61

An engineer is implementing an import operation in Cisco UCS Manager. What is the impact of performing this operation?

A. t is assigned to all the service profiles that include a host firmware policy

B. t is replaced by a new default policy without any firmware entries

C. t is set to match the host firmware policy

D. t is updated to contain the firmware entries of all the components

View answer

Correct Answer: A

Question #62

Refer to the exhibit.What must be connected to clear the HA NOT READY status?

A. ayer 1-Layer 2 ports

B. erver chassis

C. anagement ports

D. etwork uplinks

View answer

Correct Answer: B

Question #63

An engineer is performing an ISSU upgrade on the Cisco MDS 9000 Series Switch. What is the impact on the control plane of the switch?

A. t is down for less than 80 seconds

B. t remains down for more than 80 seconds but less than 140 seconds

C. t remains down until the next reboot

D. t remains up throughout the update

View answer

Correct Answer: A

Question #64

Which command reduces the amount of time it takes to complete the ISSU on a Cisco Nexus 7000 Series Switch that has dual supervisor modules and two I/O modules?

A. nsinstall all epld bootflash: parallel

B. nstall all kickstart system parallel

C. nstall all kickstart system

D. nstall all epld bootflash:

View answer

Correct Answer: B

Question #65

Refer to the exhibit.Which action must be taken before the maintenance policy can be committed?

A. pecify a maintenance time by selecting a schedule

B. ssociate a service profile to the maintenance policy

C. et the soft shutdown timer to a specific time

D. et the policy to apply the changes on the next reboot

View answer

Correct Answer: A

Question #66

Which MAC address is an HSRP version 2?

A. 842

B. 000

C. 000

D. 100

View answer

Correct Answer: C

Question #67

An infrastructure architect is analyzing the deployment type for an application. Several companies must be able to operate the application environment and integrate it with a third-party protocol. The development team also must have maximum control over their development environment, including the operating system used, Python interpreter, and corresponding libraries. Which cloud deployment solution meets these requirements?

A. rivate cloudPlatform as a Service

B. ublic cloudStorage as a Service

C. ybrid cloudSoftware as a Service

D. ommunity cloudInfrastructure as a Service

View answer

Correct Answer: C

Question #68

An engineer must configure a monitoring solution for a Cisco Nexus 9000 Series Switch based data center. The solution must provide real-time insight into the network health with subscription-based monitoring. The monitoring must be initiated from the client side, and the data must be sent via encryption. Which configuration steps complete the configuration?

A. onfigure Grafana on the Nexus switch

B. et the telemetry feature on the Nexus switch

C. ctivate SNMPv3 on the Nexus switch

D. nable GRPC on the Nexus switch

View answer

Correct Answer: B

Question #69

Refer to the exhibit. A host with a source address 10.10.10.10 sends traffic to multicast group 239.1.1.1. How do the vPC switches forward the multicast traffic?

A. f multicast traffic is received on Switch1 over the vPC peer-link, the traffic is dropped

B. f multicast traffic is received on Po10 Switch1, the traffic is forwarded out on Po1 and Po20

C. f multicast traffic is received on Po11 Switch2, the traffic is forwarded out only on Po20

D. f multicast traffic is received on Po11 Switch2, the traffic is dropped

View answer

Correct Answer: D

Question #70

Refer to the exhibit. Cisco Fabric Services is enabled in the network. Which type of IP address is used by the Cisco Fabric Services protocol?

A. Pv4 multicast address

B. Pv4 unicast address

C. Pv4 gateway address

D. Pv4 anycast address

View answer

Correct Answer: A

Question #71

Refer to the exhibit.Which backup operation type does not include the Preserve Identities feature?

A. ull state

B. ll configuration

C. ogical configuration

D. ystem configuration

View answer

Correct Answer: C

Question #72

An engineer must configure multiple EPGs on a single access port in a large Cisco ACI fabric without using VMM integration. The relevant access policies and tenant policies have been created. A single AAEP is used to configure the access ports in the fabric. Which two additional steps must be taken to complete the configuration? (Choose two.)

A. ata center

B. M name

C. P address

D. MM domain

View answer

Correct Answer: BE

Question #73

Refer to the exhibit.A flapping link issue has been reported on the vPC keepalive link. A packet capture has been activated on the Cisco Nexus switch.What is the destination IP address of the vPC keepalive packets that are sent by the switch?

A. 92

B. 92

C. 92

D. 39

View answer

Correct Answer: A

Question #74

When deploying a Cisco HyperFlex edge with a pair of switches, what is the minimum number of interfaces in trunk mode required on each HX node?

A.

B.

C.

D.

View answer

Correct Answer: B

Question #75

Which method must a network engineer use to upgrade the BIOS firmware or a Cisco UCS standalone C- Series rack-mount server?

A. se the U-ACPI Interface

B. se the Cisco host upgrade utility

C. se the Cisco hardware upgrade utility

D. se the Cisco host firmware policy

View answer

Correct Answer: B

Question #76

An engineer configures the properties of a Cisco UCS Cisco Integrated Management Controller network adapter for a standalone Cisco C-Series Server. The Failback Timeout in the vNIC was set to 600. When the failure occurs, the secondary interfaces must be used and then failback when the primary interface becomes available again. Which action must be taken to meet these requirements?

A. ype: All configuration Protocol: FTP

B. ype: Full state Protocol: SFTP

C. ype: Logical configuration Protocol: TFTP

D. ype: System configuration Protocol: SCP

View answer

Correct Answer: C

Question #77

Which two configuration settings are available in the Cisco UCS Firmware Auto Sync Server policy? (Choose two.)

A.

B.

C.

D.

View answer

Correct Answer: CE

Question #78

Refer to the exhibit. Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?

A. guestshell@guestshell ~]$ for x in {1

B. guestshell@guestshell ~]$ for x in {1

C. guestshell@guestshell ~]$ for x in (1

D. guestshell@guestshell ~]$ for x in (1

View answer

Correct Answer: A

Question #79

Which mroute state is created when Bidirectional PIM is deployed at a site?

A.

B. VPN Type-6

C. VPN Type-7

D.

View answer

Correct Answer: A

Question #80

In an FCoE environment, for which two sets of data must an interface that implements the PAUSE mechanism always provision sufficient ingress buffer? (Choose two.)

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: BD

Question #81

When the default firmware package is set to a new version, which type of policy determines the timing of server reboots during the firmware upgrade?

A. iagnostics

B. aintenance

C. ocal disk

D. IOS

View answer

Correct Answer: B

Question #82

Refer to the exhibit. An engineer needs to implement streaming telemetry on a Cisco MDS 9000 Series Switch. The requirement is for the show command data to be collected every 30 seconds and sent to receivers. Which command must be added to the configuration to meet this requirement?

A. nsr-grp 200 sample-interval 30000

B. nsr-grp 200 sample-interval 30

C. ensor-grp 200 sample-period 30

D. ensor-grp 200 sample-period 30000

View answer

Correct Answer: A

Question #83

Refer to the exhibit. A network engineer plans to upgrade the current software images of a Cisco Nexus switch. What is the impact of starting the EPLD upgrade?

A. he switch reboots one time for the new EPLD versions to take effect

B. he switch reboots multiple times for the new EPLD versions to take effect

C. he switch skips the EPLD upgrade for each EPLD device of the switch

D. he switch skips the EPLD upgrade for MIFPGA and proceeds with the other EPLD devices

View answer

Correct Answer: C

Question #84

Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch.Which two technologies can be implemented to reduce disruptions to the network during the upgrade? (Choose two.)

A. ulticast traffic forwarding is suspended

B. RIB is flushed

C. he PIM database is deleted

D. IM join messages are suspended

View answer

Correct Answer: AC

Question #85

Refer to the exhibit.The STP priority of N7K-1 and N7K-2 are the lowest in the network. Which statement describes STP on the vPC?

A. 7K-1 and N7K-2 appear as a single STP root

B. 7K-1 appears as the STP root

C. 7K-1 preempts N7K-2 as the STP root

D. 7K-2 appears as the STP root

View answer

Correct Answer: A

Question #86

Which two firmware packages are included in the Cisco UCS C-Series Rack-Mount UCS-Managed Server Software bundle? (Choose two.)

A. estrict migration

B. erver pool

C. erver

D. ustom server

View answer

Correct Answer: AB

Question #87

Refer to the exhibit. An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B. Which configuration must be implemented to monitor and export traffic to Network Analyzer?

A. W-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 tx SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination ip 10

B. W-1(config)# monitor session 5 type erspan-sourceSW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10

C. W-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 both SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination interface ethernet 2/1SW-1(config-monitor)# no shut

D. W-1(config)# monitor session 5 type erspanSW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source interface ethernet 1/1 both SW-1(config-erspan-src)# destination ip 10

View answer

Correct Answer: B

Question #88

Which statement describes monitoring Fibre Channel traffic on a Cisco UCS 6332 Fabric Interconnect?

A. ibre Channel traffic is monitored only on one vHBA per server

B. ibre Channel traffic is capable to be monitored as it is encapsulated as FCoE

C. he monitoring of Fibre Channel traffic is limited to the default VSAN

D. he destination port for monitoring must be an unassigned Fibre Channel port

View answer

Correct Answer: A

Question #89

Refer to the exhibit.What is a characteristic presented in the service profile of the UUID?

A. nique system generated

B. llocated from a UUID pool

C. endor assigned

D. ased on the hardware

View answer

Correct Answer: B

Question #90

What is a characteristic of the install all command on the Cisco Nexus Series Switch?

A. utomatically checks the image integrity

B. ontinues the upgrade process if any step in the sequence fails

C. pgrades only certain modules

D. mpacts data plane traffic

View answer

Correct Answer: A

Question #91

Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal?

A. W3# configure terminalSW3(config)# source interface port-channel 1 rxSW3(config)# source interface port-channel 2 txSW3(config)# interface ethernet 1/4SW3(config-if)# destination interface ethernet 1/4SW3(config-if)# exitSW3(config)# interface Port-channel 1-2 SW3(config-if)# switchport monitor SW3(config-if)# exit

B. W3# configure terminalSW3(config)# monitor session 2SW3(config-monitor)# source interface port-channel 1 rxSW3(config-monitor)# source interface port-channel 2 rxSW3(config)# interface ethernet 1/4 SW3(config-if)# switchport monitor SW3(config-if)# exitSW3(config)# monitor session 2SW3(config-monitor)# destination interface ethernet 1/4

C. W3# configure terminalSW3(config)# monitor session 2SW3(config-monitor)# source interface port-channel 1 txSW3(config-monitor)# source interface port-channel 2 txSW3(config)# interface Port-channel 1 SW3(config-if)# switchport monitor SW3(config-if)# exitSW3(config)# interface Port-channel 2 SW3(config-if)# switchport monitor SW3(config-if)# exit

D. W3# configure terminalSW3(config)# monitor session 2SW3(config-monitor)# source interface port-channel 1 txSW3(config-monitor)# source interface port-channel 2 rxSW3(config)# interface port-channel 1 SW3(config-if)# switchport monitor SW3(config-if)# exitSW3(config)# interface port-channel 2 SW3(config-if)# switchport monitor SW3(config-if)# exit

View answer

Correct Answer: B

Question #92

Refer to the exhibit.Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

A. hared LOM

B. isco card

C. edicated

D. hared LOM EXT

View answer

Correct Answer: AC

Question #93

An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality. Which two steps must be taken to implement the solution? (Choose two.)

A. egenerate the default key ring certificate manually

B. einstall the cluster to generate the default key ring certificate

C. eboot the SSO component of the Cisco UCS Manager

D. enerate a new default key ring certificate from the Cisco UCS Manager

View answer

Correct Answer: AB

Question #94

An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master. Which set of commands must be used to implement the scenario?

A. eature hsrpinterface vlan100ip address 10

B. eature-set hsrpinterface vlan100ip address 10

C. eature-set hsrpinterface vlan100ip address 10

D. eature hsrpinterface vlan100ip address 10

View answer

Correct Answer: A

Question #95

Refer to the exhibit. An engineer must monitor the Ethernet port and the corresponding VLAN traffic for the hyper4 device. The SW3 device is a Cisco Nexus 7000 Series Switch. Drag and drop the code snippets from the right into the boxes in the configuration to meet these requirements.

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #96

An engineer configures an Intersight Virtual Appliance and must claim over 200 targets. The engineer starts the Claim New Target Procedure. The engineer has prepared this initial comma-separated value file to provision the targets:UCSFI,10.1.1.3,user-1,pwd5516b917IMC,10.1.1.5/26,user-2,pwdc65b1c43f HX,10.1.2.1/30,user-3,pwd39913690 UCSD,1.1.1.1.user-4,pwd5003e9d5Which information must be included in the comma-separated value file to provision the targets?

A. arget type, hostname or IP address, user name, password

B. ocation, address, name, password

C. QDN, AD name, IP address, email

D. ertificate, user name, password, email

View answer

Correct Answer: A

Question #97

A network architect wants to propose a scalable network monitoring solution in which data is repeatedly acquired from network devices. The solution must use a push model and provide close to real-time access to operational data. Which technology must be used to meet these requirements?

A. LI-based scripting

B. ogging

C. NMPv3

D. treaming telemetry

View answer

Correct Answer: D

Question #98

An engineer need to implement a solution that prevents loops from occurring accidentally by connecting a switch to interface Ethernet1/1. The port is designated to be used for host connectivity. Which configuration should be implemented?

A. witch# configure terminal switch(config)# interface Ethernet1/1switch(config-if)# spanning-tree bpduguard enable

B. witch# configure terminal switch(config)# interface Ethernet1/1switch(config-if)# spanning-tree guard loop

C. witch# configure terminal switch(config)# interface Ethernet1/1switch(config-if)# spanning-tree loopguard default

D. witch# configure terminal switch(config)# interface Ethernet1/1switch(config-if)# spanning-tree bpdufilter enable

View answer

Correct Answer: A

Question #99

An engineer is configuring a backup operation on the existing Cisco UCS environment using a logical configuration.Which configuration is expected to be saved by using this backup type?

A. 6 Retention

B. 6 non-Retention

C. 2 state

D. 0/C1 state

View answer

Correct Answer: D

Question #100

An engineer must configure the HSRP protocol to implement redundancy using two Cisco Nexus Series Switches, in addition, me HSRP must meet these requirements:• switch1 must retain the primary role if switch2 goes offline.• switch1 must retain the primary role until normal conditions are restored.• switch1 and switch2 must ensure that the routing tables are converged before taking the active role. • switch2 must retain the primary role if the default gateway is not reachable. Drag and drop the configuration

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #101

A new employee must be granted access to add VLANs into an existing Cisco UCS Manager and configure NTP synchronization with date and time zone settings. Which two privileges must be granted to the employee to complete the task? (Choose two.)

A. hange the template type of Trunk-A to an updating template

B. emove the VLAN from the Trunk-A template and add the VLAN again

C. hange the template type of ESXi-Server to an updating template

D. emove both templates and recreate them as updating templates

View answer

Correct Answer: DE

Question #102

Which service profile is affected if the default host firmware policy in Cisco UCS Manager is changed?

A. ny service profile that uses the global-default host firmware policy

B. ny service profile that uses a user-created host firmware policy

C. ny service profile that has no host firmware policy defined

D. ny service profile that is not in the root sub-org

View answer

Correct Answer: A

Question #103

A Cisco UCS user called “Employee1” accidentally changed the boot policy of the Cisco UCS server at the Cisco UCS Manager root level. This change impacted all service profiles, and their storage connectivity was lost. The system administrator wants to prevent this issue from recurring in the future. The new security policy mandates that access must be restricted up to the organization level and prevent other users from modifying root policies. Which action must be taken to meet these requirements?

A. odify the privilege level assigned to the user

B. ssign users to a specific Cisco UCS locale

C. ssign the user “Employee1” the network-operator role

D. efine a custom user role and assign it to users

View answer

Correct Answer: A

Question #104

Drag and drop the firmware packages from the left onto the software bundles they belong to on the right.

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #105

Refer to the exhibit. Drag and drop each traffic flow type from the left onto the corresponding number on the right. Not all traffic flow types are used.Select and Place:

A. lease refer to Explanation section for answer(s)

View answer

Correct Answer: A

Question #106

Which virtual MAC address is the default for HSRP version 2 group 10?

A. 000

B. 000

C. 716

D. 000

View answer

Correct Answer: B

Question #107

A UCS B-Series server located in B5108 chassis 1 slot 1 is currently unavailable. The server needs to be associated with a specific service profile when it becomes available. Which associate service profile option should be selected to accomplish this goal?

A. CS-A# scope server 1 UCS-A /server# scope cimcUCS-A /server/cimc # scope mgmt-conn sideband UCS-A /server/cimc # mgmt-conn-state enabledUCS-A /server/cimc/mgmt-conn* # commit-buffer

B. CS-A# scope chassis 1 UCS-A /chassis# scope cimcUCS-A /chassis/cimc # scope mgmt-conn sidebandUCS-A /chassis/cimc/mgmt-conn # mgmt-conn-state enabled UCS-A /chassis/cimc/mgmt-conn* # commit-buffer

C. CS-A# scope chassis 1 UCS-A /chassis# scope cimcUCS-A /chassis /cimc # set mgmt-conn-state enabled UCS-A /chassis /cimc/mgmt-conn* # commit-buffer

D. CS-A# scope server 1 UCS-A /server# scope cimcUCS-A /server/cimc # scope mgmt-conn sidebandUCS-A /server/cimc/mgmt-conn #set mgmt-conn-state enabledUCS-A /server/cimc/mgmt-conn* # commit-buffer

View answer

Correct Answer: C

Question #108

What are two capabilities of the Cisco Network Assurance Engine? (Choose two.)

A. n-change traps sent to a receiver

B. eriodic push-based subscription messages

C. eriodic polling of the device status

D. D5-based authentication on polling

View answer

Correct Answer: AB

Question #109

An engineer must configure OSPF in the data center. The external routes have already been redistributed into OSPF. The network most meets these criteria:• The data center servers must reach services in the cloud and the services behind the redistributed routes.• The exit point toward the Internet should be propagated only when there is a dynamically learned default route from the upstream router.Which feature is required?

A. tubby area

B. otally stubby area

C. efault-information originate

D. efault-information originate always

View answer

Correct Answer: C

Question #110

An engineer must configure OSPFv2 connectivity between a pair of Cisco Nexus switches. The connection between the switches must meet these requirements:-Use unicast for updates.-Use decentralized communication of updates.-Full adjacency between switches.Which configuration is needed to meet these requirements?

A. ilter list between the neighbors

B. tub area between the neighbors

C. irtual link between the neighbors

D. nterface with a type of p2p network

View answer

Correct Answer: A

Question #111

Refer to the exhibit. Which action completes the vPC domain implementation?

A. dd the vPC member ports to the vPC channel group

B. onfigure the system MAC on the vPC domain

C. nclude the VRF management on the vPC domain

D. llow VLANs on the vPC peer link member interfaces

View answer

Correct Answer: D

Question #112

Which method must a network engineer use to upgrade the BIOS firmware or a Cisco UCS standalone C-Series rack-mount server?

A. se the U-ACPI Interface

B. se the Cisco host upgrade utility

C. se the Cisco hardware upgrade utility

D. se the Cisco host firmware policy

View answer

Correct Answer: B

Question #113

An engineer must implement a VXLAN-based data center interconnect. The long-distance transport provided by a service provider is IP-based, supports a maximum MTU of 1554 bytes, and does not support outbound traffic replication. Which action must be taken to build the data center interconnect?

A. nnounce host reachability over BGP

B. reate an IP access list and associate it with VNI to replicate traffic to remote VTEPs

C. onfigure a route map to associate the IPs of the remote VTEPs

D. mplement BGP EVPN ingress replication

View answer

Correct Answer: D

Question #114

An engineer performs a set of configuration changes for the vPC domain using Session Manager. Which two commands are used to verify the configuration and apply the device changes when no errors are returned? (Choose two.)

A. ll uplink FCoE ports

B. ll vNICs from the service profile that correspond to this server

C. ll uplink Ethernet ports

D. ll vHBAs from the service profile that correspond to this server

View answer

Correct Answer: AE

Question #115

A network engineer is deploying a Cisco All-Flash HyperFlex solution. Which local storage configuration is required for the operating system and persistent logging?

A. ne solid state drive

B. wo SATA drives

C. ne SATA drive

D. wo solid state drives

View answer

Correct Answer: A

Question #116

Refer to the exhibit. Which type of backup is required to restore a Cisco UCS configuration?

A. ystem configuration

B. ll configuration

C. ull state

D. ogical configuration

View answer

Correct Answer: C

Question #117

Refer to the exhibit. An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?

A. pc local role-priority 4000

B. eer-switch

C. ystem-mac 0123

D. eer-gateway

View answer

Correct Answer: B

Question #118

An engineer must configure a VXLAN routing on a Cisco Nexus 9000 Series Switch. The engineer requires a solution where all the leaf switches have the same gateway MAC and IP addresses. Which configuration set accomplishes this task?

A. X9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BBNX9K(config)# interface VLAN-interface-nameNX9K(config-if)# vrf member vrf-name NX9K(config-if)# fabric forwarding mode anycast-gateway

B. X9K(config)# install feature-set fabricNX9K(config)# feature-set fabricNX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BBNX9K(config)# interface VLAN-interface-nameNX9K(config-if)# fabric forwarding mode anycast-gateway

C. X9K(config)# install feature-set fabricNX9K(config)# feature-set fabricNX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)#interface VLAN-interface-nameNX9K(config-if)# vrf member vrf-nameNX9K(config-if)# fabric forwarding mode anycast-gateway

D. X9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BBNX9K(config)# interface VLAN-interface-nameNX9K(config-if)# fabric forwarding mode anycast-gateway

View answer

Correct Answer: A

Question #119

Refer to the exhibit.Which statement about the ERSPAN configuration in this environment is true?

A. he session number of the source of ERSPAN spanned traffic must have a session ID of 47 for the traffic analyzer to receive the traffic

B. ost B is the source of ERSPAN spanned traffic and host A is the traffic analyzer

C. he session number of the source of ERSPAN spanned traffic must have a session ID of 48 for the traffic analyzer to receive the traffic

D. ost A is the source of ERSPAN spanned traffic and host B is the traffic analyzer

View answer

Correct Answer: D

Question #120

Refer to the exhibit. A network engineer is implementing a configuration checkpoint on a Cisco Nexus 9000 Series Switch. The configuration must skip any existing vPC configuration errors and must complete if there are any configuration errors. The engineer finished the vPC domain configuration part. Which command completes the checkpoint implementation?

A. est-effort

B. top-at-first-failure

C. tomic

D. erbose

View answer

Correct Answer: A

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now

Prepare Strategically for the Cisco 350-601 DCCOR Exam with Practice Tests

View Answers after Submission

DON'T WANT TO MISS A THING?

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE! Get Now

Prepare Strategically for the Cisco 350-601 DCCOR Exam with Practice Tests

View Answers after Submission

100% Pass Cisco, PMP, CISA, CISM, AWS Practice test on SALE!
Get Now