Free HP HPE7-A03 Practice Questions & Answers 2026 Part1 | Aruba Certified

A global cruise line company needs to refresh its current fleet. They will refresh the 'insides' of the ship to be cost-effective and increase their sustainability. They will replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh its current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guests.Each ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins, 100 technical rooms). The core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch.The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by single-mode fiber (SMF), of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (980 ft), type used is OS1. Each cabin is connected by a single OM2 pair to the IDF, maximum length 60 m (200 ft). Each technical room is connected by a single OM2 pair to the IDF, with lengths 100--150 m (320--500 ft).For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10 GbE to handle the increased network traffic, and the technical rooms need redundant power.The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN infrastructure is based on the 200/300 series indoor and outdoor APs running InstantOS (less than 300 APs), the customer has no change in WLAN requirements.The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new Internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because the Internet connection is guaranteed.A week after the presentation of your design to the CIO of the cruise line company, the CIO calls you to discuss increasing the security of the wired network infrastructure. Since one of their competitors had one of their cruise ships cyber hacked, the CSO of the cruise line has mandated increased security on the wired network. They have heard about dynamic segmentation and central and decentral overlay networks. For their POS (Point of Sale) systems, they need a low-latency network connection between the POS system and the PCS server in the data center on the ship. Also, the CSO wants to enhance the WLAN security as well by tunneling all user traffic.What solution fits the customer's requirements?

A global cruise line company needs to refresh its current fleet. They win refresh the insides' of the ship to be cost-effective and increase their sustain ability. They Mill replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh Us current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guestsEach ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins. 100 technical rooms). The Core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch.The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by SMF. of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (930 ft) and the type used is 0S1. Each cabin is connected by a single 0M2 pair to the IDF. the maximum length is 60 meters (200 ft). Each technical room is connected by a single 0M2 pail to the IDF. with lengths between 100 and 150 meters (320 and 500 ft).For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10GbEto handle the increased network traffic, and the technical rooms need redundant power.The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN Infrastructure is based on the 200/300 series Indoor and outdoor APs running instantOS (less than 300 APs). the customer has no change in WLAN requirements.The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because Internet connection is guaranteed.The week after the presentation of your design to the CIO of the cruise line company, the CIO calls you to discuss increasing the security on the wired network infrastructure. Since one of their competitors had one of their cruise ships cyber hacked, the CSO of the cruise line has mandated increased security on the wired network. They have heard about dynamic segmentation and central and decentral overlay networks. For their POS systems, they need a low-latency network connection between the POS system and the POS server in the data center on the ship. Also, the CSO wants to enhance the WLAN security as well by tunneling all user traffic.What solution fits the customer's requirements?

You ate presenting your network design solution to your customer. What Is important to include in your presentation?

ACME retail has 38 locations spread out across Ave US states and two provinces in Canad

The customer recently found out that Aruba OS-CX switches are capable of Application Recognition. What requirements should be fulfilled in order to do this? (Select two.) Aruba OS-CX switches, specifically the Aruba 6400 and 6300F/M models, are designed to support advanced networking features, including Application Recognition, with the Aruba CX Advanced License. The Advanced License enables enhanced capabilities such as deeper visibility into application flows, advanced routing features, and improved network analytics. Application Recognition allows these switches to identify and classify applications running on the network, enabling more intelligent and dynamic network policies and improving overall network performance and security. The requirement for an Aruba CX Advanced License on these specific models ensures that the necessary software features and support are available to leverage Application Recognition capabilities effectively.

You hired a junior engineer to assist you with a large-scale network infrastructure project. The engineer has never worked on such a complex project before and wants to better understand the role that each stakeholder will play in the project.What is the role of the Network Designer/Architect in this project?

Which access switch oversubscription option would be best suited for CAD desktops?

A large multinational financial institution has contracted you to design a new full-stack wired and wireless network for their new 6-story regional office building. The bottom two floors of this facility willbe retail space for a large banking branch. The upper floors will be carpeted office space for corporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off site and will be out of scope for this project. The customer is underserved by its existing L2based network Infrastructure and would like to take advantage of modern best practices in the new design. The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.

A customer wants to have the ability to show network usage. Which product would allow them to have this visibility?

A large multinational financial institution has contracted you to design a new full-stack wired andwireless network for their new 6-story regional office building. The bottom two floors of this facilitywill be retail space for a large banking branch. The upper floors will be carpeted office space forcorporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off siteand will be out of scope for this project. The customer is underserved by its existing L2-basednetwork infrastructure and would like to take advantage of modern best practices in the new design.The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets forcustomer service, and there will be a mix of wired and wireless devices throughout the retail floors.The corporate users will primarily use wireless for connectivity, but several wired clients, printers,and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of"smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics,and other location-based servicesThe client is looking to utilize lower-cost Aruba OS-CX switches in their wiring closets. They calculatethat each closet will need a stack or qty 6 POE (AT) and qty 0 Gigabit Ethernet switches stacked withlow-cost OACs.Which series switch should you recommend?

A large multinational financial institution has contracted you to design a new full-stack wired andwireless network for their new 6-story regional office building. The bottom two floors of this facilitywill be retail space for a large banking branch. The upper floors will be carpeted office space forcorporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off siteand will be out of scope for this project. The customer is underserved by its existing L2-basednetwork infrastructure and would like to take advantage of modern best practices in the new design.The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets forcustomer service, and there will be a mix of wired and wireless devices throughout the retail floors.The corporate users will primarily use wireless for connectivity, but several wired clients, printers,and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of"smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics,and other location-based servicesThe client decided that wired headless devices would be authenticated using Mac Authenticationand would have RADIUS attributes sent back to the NAD to assign VLAN and port access parametersto the authentication session on the switch port.What would be critical in making this a successful deployment? {Select two.)

A large multinational financial institution has contracted you to design a new full-stack wired and wireless network for their new 6-story regional office building. The bottom two floors of this facility will be retail space for a large banking branch. The upper floors will be carpeted office space for corporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off site and will be out of scope for this project. The customer is underserved by its existing L2-based network infrastructure and would like to take advantage of modern best practices in the new design. The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets for customer service, and there will be a mix of wired and wireless devices throughout the retail floors. The corporate users will primarily use wireless for connectivity, but several wired clients, printers, and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of "smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics, and other location-based servicesThe client would like to ensure full wireless coverage in its 40 m x 40 m i 130 ft x 130 ft) auditorium during company functions while maintaining the fewest APs for aesthetic purposes WI-FI6 APs are a minimum requirement.Which AP series would you use In the auditorium's 1.000 seats with a maximum take rate of 80%?

A global cruise line company needs to refresh its current fleet. They win refresh the insides' of the ship to be cost-effective and increase their sustain ability. They Mill replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh Us current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guests Each ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins. 100 technical rooms). The Core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch. The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by SMF. of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (930 ft) and the type used is 0S1. Each cabin is connected by a single 0M2 pair to the IDF. the maximum length is 60 meters (200 ft). Each technical room is connected by a single 0M2 pail to the IDF. with lengths between 100 and 150 meters (320 and 500 ft). For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10GbEto handle the increased network traffic, and the technical rooms need redundant power. The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN Infrastructure is based on the 200/300 series Indoor and outdoor APs running instantOS (less than 300 APs). the customer has no change in WLAN requirements. The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because Internet connection is guaranteed. Based on the best practices, what should you recommend as the most cost-effective switch model for the cabins? For the cabin switches in the global cruise line's fleet refresh project, the most cost-effective switch model that meets the requirement for fan-less operation, 10GbE uplink capability, and PoE support is the HPE Aruba Networking 6200F 12G Class4 PoE 2G/2SFP+. This switch model offers a compact form factor with sufficient port density for cabin connectivity, Power over Ethernet for powering devices directly through the network cable, and SFP+ ports for high-speed uplink connections to the distribution switches. This choice is in line with the company's aim to upgrade the network infrastructure to handle increased traffic while maintaining a focus on cost-effectiveness and sustainability. The 6200F series is designed for exactly such environments, providing reliable performance and energy efficiency, which is crucial for the limited space and power availability in a ship setting.

A global cruise line company needs to refresh its current fleet. They win refresh the insides' of the ship to be cost-effective and increase their sustain ability. They Mill replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh Us current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guestsEach ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins. 100 technical rooms). The Core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch.The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by SMF. of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (930 ft) and the type used is 0S1. Each cabin is connected by a single 0M2 pair to the IDF. the maximum length is 60 meters (200 ft). Each technical room is connected by a single 0M2 pail to the IDF. with lengths between 100 and 150 meters (320 and 500 ft).For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10GbEto handle the increased network traffic, and the technical rooms need redundant power.The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN Infrastructure is based on the 200/300 series Indoor and outdoor APs running instantOS (less than 300 APs). the customer has no change in WLAN requirements.The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because Internet connection is guaranteed.Based on the best practices and customer requirements, what is the correct WUN approach?

A large multinational financial institution has contracted you to design a new full-stack wired andwireless network for their new 6-story regional office building. The bottom two floors of this facilitywill be retail space for a large banking branch. The upper floors will be carpeted office space forcorporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off siteand will be out of scope for this project. The customer is underserved by its existing L2-basednetwork infrastructure and would like to take advantage of modern best practices in the new design.The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets forcustomer service, and there will be a mix of wired and wireless devices throughout the retail floors.The corporate users will primarily use wireless for connectivity, but several wired clients, printers,and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of"smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics,and other location-based servicesThe client would take to ensure redundant RADIUS resources in each of their three geographicalregions (AMER. EME

Which is true with regard to device capabilities?

It has been identified that the client's existing network is having to retransmit packets due to possible hardware or configuration issues. A review of hardware configuration and transport reliability will need to be assessed prior to completing the new design.What should this phenomenon be classified as?

The client's existing network is experiencing trouble with voice occasionally dropping out on phone calls between office locations. It is determined that no packet loss is occurring and QOS is likely the cause.With what phenomenon is the client currently experiencing issues?

A large multinational financial institution has contracted you to design a new full-stack wired and wireless network for their new 6-story regional office building. The bottom two floors of this facility will be retail space for a large banking branch. The upper floors will be carpeted office space for corporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off site and will be out of scope for this project. The customer is underserved by its existing L2-based network infrastructure and would like to take advantage of modern best practices in the new design. The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets for customer service, and there will be a mix of wired and wireless devices throughout the retail floors. The corporate users will primarily use wireless for connectivity, but several wired clients, printers, and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of "smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics, and other location-based servicesThe client has provided floorplans. wall density, and ceiling heights tor the wireless deployment inthe carpeted office spaceWhat else will be needed to write an accurate bill of material? (Select two)

A global cruise line company needs to refresh its current fleet. They win refresh the insides' of the ship to be cost-effective and increase their sustain ability. They Mill replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh Us current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guestsEach ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins. 100 technical rooms). The Core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch.The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by SMF. of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (930 ft) and the type used is 0S1. Each cabin is connected by a single 0M2 pair to the IDF. the maximum length is 60 meters (200 ft). Each technical room is connected by a single 0M2 pail to the IDF. with lengths between 100 and 150 meters (320 and 500 ft).For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10GbEto handle the increased network traffic, and the technical rooms need redundant power.The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN Infrastructure is based on the 200/300 series Indoor and outdoor APs running instantOS (less than 300 APs). the customer has no change in WLAN requirements.The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because Internet connection is guaranteed.Based on the best practices, what should you recommend as the correct optic type for the connection between the IDF and the cabins?

What is true about 1000 Base-LX single mode transceivers?

A large multinational financial institution has contracted you to design a new full-stack wired and wireless network for their new 6-story regional office building. The bottom two floors of this facility will be retail space for a large banking branch. The upper floors will be carpeted office space for corporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off site and will be out of scope for this project. The customer is underserved by its existing L2-based network infrastructure and would like to take advantage of modern best practices in the new design. The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge. The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets for customer service, and there will be a mix of wired and wireless devices throughout the retail floors. The corporate users will primarily use wireless for connectivity, but several wired clients, printers, and hard VoIP phones will be in use. The customer is also planning on renovating the corporate office space in order to take advantage of "smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics, and other location-based services The client decides that they would like for all of their exposed printer, conference room, and VoIP phone connections to be controlled by a stateful firewall What could be planned to ensure that these ports will meet the customer's requirements? To control exposed printer, conference room, and VoIP phone connections with a stateful firewall, utilizing Tunneled Node functionality would be effective. Tunneled Node allows for the encapsulation of wired Ethernet traffic into a user-based tunnel, similar to how wireless traffic is handled. This means that traffic from these devices can be sent through a centralized controller where stateful firewall policies can be applied. This setup ensures that the specific ports used by these devices are subjected to the same level of security scrutiny and policy enforcement as wireless traffic, aligning with the client's requirements for a secure and controlled network environment.

A large multinational financial institution has contracted you to design a new full-stack wired andwireless network for their new 6-story regional office building. The bottom two floors of this facilitywill be retail space for a large banking branch. The upper floors will be carpeted office space forcorporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off siteand will be out of scope for this project. The customer is underserved by its existing L2-basednetwork infrastructure and would like to take advantage of modern best practices in the new design.The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets forcustomer service, and there will be a mix of wired and wireless devices throughout the retail floors.The corporate users will primarily use wireless for connectivity, but several wired clients, printers,and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of"smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics,and other location-based servicesThe client has provided floorplans. wall density, and ceiling heights tor the wireless deployment inthe carpeted office spaceWhat else will be needed to write an accurate bill of material? (Select two)

which documentation resources con be used for finding validated information on Aruba products that assist the architect in building the solution design? (Select three.)

ACME retail has 38 locations spread out across Ave US states and two provinces in Canad a. They are looking to grow 20% over the next two years. They have an HO with a staff of 200 employees. The organization has eight Regional Managers and two VPs who work from home and the road. Stores typically have 17 employees on average per location. The two warehouses have a remote loading system and 20 employees each to load the trucks and fulfill the online orders. The warehouse has 40-foot ceilings and large metal racks to store inventory. The main location is 240K sq ft (22300 st) m) and the Canadian warehouse Is 130K sq ft (12100 sq ml. The forkllfts on the loading docks are equipped with a wireless tablet on board. A typical store Is reportedly about 60.000 sq ft (5575 sqm) and smaller stores are planned at 25.000 sq ft '2320 sq mi. The locations need to expand the abilities to vendors that need to add setup displays or Interactive kiosks in the stores. The current Infrastructure was installed In 2015 and used wireless N technology in a coverage model. The wiring is CatS. and they are unsure of the fiber connections. The inventory is all placed on the floor when it is delivered to the local store. Inventory control is handled through Zebra barcode scanners, and they have had a lot of issues in getting signals throughout the stores and this makes monthly inventory difficult. The organization has a small help desk to troubleshoot issues that happen at the retail locations and PC support for the office. The company is looking to upgrade away from the current pbx system later this year. With the need to grow and cut costs, they are interested in moving the data to the cloud but need to get almost real-time inventory control for the online service to function. The network has all been wired over the last ten years, but with the new systems being all wireless, they have seen the trend to offer wireless to all the vendors for their needs but also would like to allow employees, guests, and contractors all to use it. With the new IT director starting next week, the project has been set by the CTO of the company. The marketing group has asked how they can interact with the customers and get more info, while the IT support desk needs to cut staff in halt. The. office has an MDF and two IDFs located on floors one and two. The HOF is in the basement, and you have multiple WAN circuits for the HO links. Each store has a local handoff from the cable company (ethernet) In the middle of the store in the office, so distance for the wiring is not an issue. The customer has budget concerns but does want something that could last 7+ years. Which two projects does the customer have in the planning state? (Select two)

A global cruise line company needs to refresh its current fleet. They will refresh the 'insides' of the ship to be cost-effective and increase their sustainability. They will replace the complete WLAN/LAN hardware of the ship. In this refresh, the company will not refresh its current security requirements. The CIO also wants to limit the number of unused ports in the switches. Future expansion will always mean a refresh of hardware. They start with the smallest ship with a maximum of 800 guests. Each ship has a LAN infrastructure consisting of two core switches, up to 10 redundant distribution switches, and up to 500 access switches (400 cabins, 100 technical rooms). The core switches are located in the MDF of the ship and the distribution switches are located in the IDFs of the ship. Each cabin and technical room gets one single access switch. The cabling structure of the ship will not be refreshed. Each IDF is connected to the MDF by single-mode fiber (SMF), of which two pairs are available for the interconnect between the core and distribution. The length of SM fiber between MDF and IDF is less than 300 meters (980 ft), type used is OS1. Each cabin is connected by a single OM2 pair to the IDF, maximum length 60 m (200 ft). Each technical room is connected by a single OM2 pair to the IDF, with lengths 100--150 m (320--500 ft). For each cabin/technical room the customer is looking to replace their current fan-less 2530/2540 without changing the requirements, except they need to upgrade the uplink to distribution switch to 10 GbE to handle the increased network traffic, and the technical rooms need redundant power. The WLAN infrastructure will be 1:1 refreshed without new cabling or new AP locations. Their WLAN infrastructure is based on the 200/300 series indoor and outdoor APs running InstantOS (less than 300 APs), the customer has no change in WLAN requirements. The cruise line company will replace its current Internet connection before the LAN/WLAN refresh. The new Internet connection will provide a 99.8% uptime, which is needed to ensure the paid guest Wi-Fi is always operational. With this new Internet connection, the CIO of the cruise line wants to base the design on the ESP architecture from Aruba because the Internet connection is guaranteed. A week after the presentation of your design to the CIO of the cruise line company, the CIO calls you to discuss increasing the security of the wired network infrastructure. Since one of their competitors had one of their cruise ships cyber hacked, the CSO of the cruise line has mandated increased security on the wired network. They have heard about dynamic segmentation and central and decentral overlay networks. For their POS (Point of Sale) systems, they need a low-latency network connection between the POS system and the PCS server in the data center on the ship. Also, the CSO wants to enhance the WLAN security as well by tunneling all user traffic. What solution fits the customer's requirements? Comprehensive and Detailed Explanation From Exact Extract: Aruba's ESP Campus Access Design and NetConductor Architecture guides outline the validated roles of devices in dynamic segmentation deployments. Access Layer (Edge): Aruba CX 6300 The CX 6300 provides 10 Gb uplinks to distribution, advanced features like VXLAN and EVPN, and support for role-based access control at the edge. It is the recommended choice for modern edge deployments in an ESP fabric. Route Reflector (RR): Aruba CX 8325 The CX 8325 is optimized for routing and control-plane operations. As a route reflector, it scales overlay BGP sessions and distributes policies/roles through the fabric. It is explicitly referenced as the ideal RR platform in Aruba ESP campus validated designs. Stub/Border: Aruba CX 8360 The CX 8360 family provides advanced aggregation and fabric services. It supports VXLAN, EVPN, and border routing functions, making it the right choice for stub/border persona in ESP designs. WLAN Gateway: Aruba 9240 The Aruba 9200/9240 series gateways provide role-based policy enforcement for tunneled WLAN traffic. They terminate GRE/IPsec tunnels from APs, enforce user policies, and forward into the fabric. This is critical to meet the requirement of tunneling all WLAN user traffic for enhanced security. Dynamic Segmentation with NetConductor Aruba Central NetConductor enables centralized definition and orchestration of user roles and segmentation policies. Roles are automatically enforced across the fabric using VXLAN with Group-Based Policy (GBP). This supports both centralized tunneling (for WLAN traffic) and distributed segmentation (for wired POS traffic requiring low latency). Requirement Mapping: Low-latency POS traffic Distributed role enforcement within the fabric via 8360/8325. Secure WLAN traffic User traffic tunneled to the 9240 gateway for role-based enforcement. 10 Gb uplinks and redundancy Provided by 6300 edge switches with dual power options in technical rooms. ESP architecture NetConductor automates overlay, segmentation, and role orchestration. Other options are eliminated because: A uses 3320 for RR, which lacks overlay fabric scalability. B uses 8320 for RR (possible, but Aruba recommends 8325 for RR roles in NetConductor designs). D omits the WLAN Gateway, which is required to tunnel WLAN traffic. E uses 6200 at the edge, which does not provide the required 10 Gb uplink capability. Therefore, Option C is the only design that fully satisfies the cruise line's requirements while aligning with Aruba's ESP Campus validated architectures. Reference Extracts (Aruba Official Study & Design Guides): Aruba ESP Campus Design Guide: device personas (edge, RR, stub/border, gateway) and NetConductor integration. Aruba NetConductor Technical Overview: VXLAN-GBP, dynamic segmentation, and centralized role enforcement. Aruba Dynamic Segmentation Solution Overview: tunneling of WLAN traffic, role-based security across wired and wireless. Aruba CX Switch Series Data Sheets: CX 6300 (edge with 10 Gb uplinks), CX 8325 (RR), CX 8360 (border/stub), Aruba 9240 (WLAN gateway).

A large multinational financial institution has contracted you to design a new full-stack wired andwireless network for their new 6-story regional office building. The bottom two floors of this facilitywill be retail space for a large banking branch. The upper floors will be carpeted office space forcorporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off siteand will be out of scope for this project. The customer is underserved by its existing L2-basednetwork infrastructure and would like to take advantage of modern best practices in the new design.The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets forcustomer service, and there will be a mix of wired and wireless devices throughout the retail floors.The corporate users will primarily use wireless for connectivity, but several wired clients, printers,and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of"smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics,and other location-based servicesThe client would like to ensure full wireless coverage in its 40 m x 40 m i 130 ft x 130 ft) auditoriumduring company functions while maintaining the fewest APs for aesthetic purposes WI-FI6 APs are aminimum requirement.Which AP series would you use In the auditorium's 1.000 seats with a maximum take rate of 80%?

A large multinational financial institution has contracted you to design a new full-stack wired and wireless network for their new 6-story regional office building. The bottom two floors of this facility will be retail space for a large banking branch. The upper floors will be carpeted office space for corporate users, each floor being approximately 100.000 sq ft (9290 sqm). Data centers are all off site and will be out of scope for this project. The customer is underserved by its existing L2-based network infrastructure and would like to take advantage of modern best practices in the new design. The network should be fully resilient and fault-tolerant, with dynamic segmentation at the edge.The retail space will include public guest Wi-Fi access. Retail associates will have corporate tablets for customer service, and there will be a mix of wired and wireless devices throughout the retail floors. The corporate users will primarily use wireless for connectivity, but several wired clients, printers, and hard VoIP phones will be in use.The customer is also planning on renovating the corporate office space in order to take advantage of "smart office' technology. These improvements will drive blue-dot wayfinding. presence analytics, and other location-based servicesThe client decides that they would like for all of their exposed printer, conference room, and VoIP phoneconnections to be controlled by a stateful firewallWhat could be planned to ensure that these ports will meet the customer's requirements?

The clients existing network is experiencing trouble with voice occasionally dropping out on phone calls between office locations, it Is determined that no packet loss is occurring and QOS is likely the cause. With what phenomenon Is the client currently experiencing issues? A) B) C)

The customer recently found out that Aruba OS - CX switches are capable of Application Recognition. What requirements should be fulfilled in order to do this? (Select two.)