Free Cisco 300-620 DCACI Practice Questions 2026 Part4

Question #1

Which device is the pervasive gateway shown installed on?

A. proxy spine switch

B. VMM switch

C. leaf switch

D. spine switch

View answer

Correct Answer: C

Question #2

An engineer created two interface protocol policies called Pol_CDP40275332 and Pol_LLDP46783451. The policies must be used together in a single policy. Which ACI object must be used?

A. interface policy group

B. switch policy group

C. switch profile

D. interface profile

View answer

Correct Answer: A

Question #3

A customer migrates a legacy environment to Cisco ACI. A Layer 2 trunk is configured to interconnect the two environments. The customer also builds ACI fabric in an application-centric mode. Which feature should be enabled in the bridge domain to reduce instability during the migration?

A. Set Multi-Destination Flooding to Flood in BD

B. Enable Flood in Encapsulation

C. Set Multi-Destination Flooding to Flood in Encapsulation

D. Disable Endpoint Dataplane Learning

View answer

Correct Answer: C

Question #4

Refer to the exhibit. An engineer must migrate the web servers and backup servers from the legacy network to a Cisco ACI environment in the corresponding EPGs. The requirement is to allow communication between the servers in the web EPG and the backup EPG without creating contracts. Which action meets the requirements?

A. Configure the Enforced Bridge Domain status flag

B. Set the direction of Policy Enforcement to Egress

C. Set IP Data-plane learning to Enabled

D. Set Policy Control Enforcement to Unenforced

View answer

Correct Answer: D

Question #5

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #6

New ESXi hosts are procured in a data center compute expansion project. An engineer must update the configuration on the Cisco APIC controllers to support the addition of the new servers to the existing VMM domain. Which action should be taken to support this change?

A. Create a range of internal VLANs in the associated VLAN pool

B. Set the encapsulation mode as VXLAN

C. Enable infrastructure VLAN in the associated AEP

D. Map the leaf interface selector to the AEP that is associated with the VMM domain

View answer

Correct Answer: D

Question #7

An organization has encountered many STP-related issues in the past due to failed hardware components.They are in the process of long-term migration to a newly deployed ACI fabric. Senior engineers are worried that spanning-tree loops in the existing network may be extended to the ACI fabric. Which feature must be enabled on the ACI leaf ports to protect the fabric from spanning-tree loops?

A. BPDU Guard

B. per-VLAN MCP

C. Storm Control

D. BPDU Filter

View answer

Correct Answer: B

Question #8

Refer to the exhibit.An engineer must implement the inter-tenant service graph. Which set of actions must be taken to accomplish this goal?

A. * Define the contract in the provider tenant and export it to the consumer tenant

B. * Define the contract in the provider tenant and export it to the consumer tenant

C. * Define the contract in the provider tenant and export it to the provider tenant

D. * Define the contract in the provider tenant and export it to the provider tenant

View answer

Correct Answer: B

Question #9

Refer to the exhibit. An engineer must migrate workloads from the brownfield network to the Cisco ACI fabric. The VLAN 10 default gateway remains in the router located in the brownfield network. The bridge domain has already been associated with L2Out. Which two actions must be taken to migrate the workloads? (Choose two.)

A. Enable ARP Flooding

B. Configure Multi-Destination Flooding Flood in Encapsulation

C. Select limit IP learning to Subnet

D. Set L2 Unknown Unicast Flood

E. Map the MAC address of the default gateway to the bridge domain

View answer

Correct Answer: AD

Question #10

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #11

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #12

Which device is the pervasive gateway shown installed on?

A. proxy spine switch

B. VMM switch

C. leaf switch

D. spine switch

View answer

Correct Answer: C

Question #13

Which type of policy configures the suppression of faults that are generated from a port being down?

A. fault lifecycle assignment

B. event lifecycle assignment

C. fault severity assignment

D. event severity assignment

View answer

Correct Answer: C

Question #14

Which tunnel endpoint is shown in this output from interface Io0?

A. physical

B. fabric

C. dynamic

D. headend replication

View answer

Correct Answer: A

Question #15

An engineer is implementing a connection that represents an external bridged network. Which two configurations are used? (Choose two.)

A. Layer 2 remote fabric

B. Layer 2 outside

C. Layers 2 internal

D. Static path binding

E. VXLAN outside

View answer

Correct Answer: BD

Question #16

What must be enabled in the bridge domain to have the endpoint table learn the IP addresses of endpoints?

A. L2 unknown unicast: flood

B. GARP based detection

C. unicast routing

D. subnet scope

E. Reveal Answer

View answer

Correct Answer: C

Question #17

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #18

An ACI administrator notices a change in the behavior of the fabric. Which action must be taken to determine if a human intervention introduced the change?

A. Inspect event records in the APIC UI to see all actions performed by users

B. Inspect /var/log /audit_messages on the APIC to see a record of all user actions

C. Inspect audit logs in the APIC UI to see all user events

D. Inspect the output of show command history in the APIC CLI

View answer

Correct Answer: C

Question #19

Refer to the exhibit. Refer to the exhibit. Server A is connected to the Cisco ACI fabric using two teamed interfaces. One interface in a team is configured as active and the other remains in standby mode. When a failover occurs and the standby interface becomes active, it uses its built-in MAC address to send traffic. Which bridge domain configuration must be applied to resolve the issue?

A. AConfigure Hardware proxy

B. BSet L2 Unknown Unicast to Flood

C. CEnable ARP flooding

D. DActivate Limit IP Learning to Subnet

View answer

Correct Answer: C

Question #20

Which device is the pervasive gateway shown installed on?

A. proxy spine switch

B. VMM switch

C. leaf switch

D. spine switch

View answer

Correct Answer: C

Question #21

Which switch type is discovered first in the Cisco ACI fabric discovery process?

A. spine

B. distribution

C. leaf

D. access

View answer

Correct Answer: C

Question #22

Refer to the exhibit. An engineer must configure a bridge domain inside the Cisco ACI fabric called BD. The configuration must permit EP2 and EP3 to reach EP1. Which configuration must be applied on the bridge domain to accomplish this goal?

A. Define the Pervasive gateway on BD

B. Enable L2 Unknown unicast flooding

C. Optimize L2 Unknown unicast traffic

D. Configure unicast routing within B

View answer

Correct Answer: B

Question #23

An engineer is troubleshooting fabric discovery in a newly deployed Cisco ACI fabric and analyzes this output:Which ACI fabric address is assigned to interface lo1023?

A. VXLAN tunnel endpoint

B. Physical tunnel endpoint

C. Fabric tunnel endpoint

D. Dynamic tunnel endpoint

View answer

Correct Answer: C

Question #24

Which two external entities are referenced by an AEP? (Choose two.)

A. AVMware vCenter server

B. BVMM domain

C. CLayer 3 domain

D. DHypervisor

E. EFibre Channel switch

View answer

Correct Answer: BC

Question #25

What is the function of an HTTP GET request during Cisco ACI fabric discovery?

A. It allows neighbor discovery of leaf switches

B. It downloads firmware image on leaf switches

C. It pushes policy elements from Cisco APIC to leaf switches

D. It assigns VTEP IPs to leaf switches

View answer

Correct Answer: A

Question #26

An ACI administrator notices a change in the behavior of the fabric. Which action must be taken to determine if a human intervention introduced the change?

A. nspect event records in the APIC UI to see all actions performed by users

B. nspect /var/log/audit_messages on the APIC to see a record of all user actions

C. nspect audit logs in the APIC UI to see all user events

D. nspect the output of show command history in the APIC CLI

View answer

Correct Answer: C

Question #27

Which switch type is discovered first in the Cisco ACI fabric discovery process?

A. spine

B. distribution

C. leaf

D. access

View answer

Correct Answer: C

Question #28

Which component provides Cisco ACI fabric with Layer 2 and Layer 3 connectivity across pods and physical locations?

A. Inter-Pod Network

B. VXLAN overlay

C. COOP control plane

D. Cisco APIC control cluster

View answer

Correct Answer: A

Question #29

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #30

An engineer is creating a configuration import policy that must terminate if the imported configuration is incompatible with the existing system. Which import modeachieves this result?

A. merge

B. atomic

C. best effort

D. replace

View answer

Correct Answer: B

Question #31

For which type of endpoint entry does a Cisco ACI leaf switch keep the original TEP source address instead of rewriting the outer source IP address to its TEP address?

A. local entry

B. remote entry

C. bounce entry

D. COOP entry

View answer

Correct Answer: C

Question #32

A Cisco APIC is configured to authenticate users by using RADIUS by default. The network administrator must ensure that the users can access the APIC GUI with a local account if the RADIUS server is unreachable. Which action achieves this goal?

A. reate an additional login domain to associate with local accounts

B. onfigure the fallback login domain to reference Local Realm

C. et RADIUS Realm to connect with Console Authentication

D. nable Fallback Check for Default Authentication

View answer

Correct Answer: B

Question #33

What is the function of an HTTP GET request during Cisco ACI fabric discovery?

A. It allows neighbor discovery of leaf switches

B. It downloads firmware image on leaf switches

C. It pushes policy elements from Cisco APIC to leaf switches

D. It assigns VTEP IPs to leaf switches

View answer

Correct Answer: A

Question #34

A network engineer must design a method to allow the Cisco ACI to redirect traffic to the firewalls. Only traffic that matches specific L4-L7 policy rules should be redirected. The load must be distributed across multiple firewalls to scale the performance horizontally. Which action must be taken to meet these requirements?

A. Configure ACI Service Graph with Unidirectional PBR

B. Implement ACI Service Graph with GIPo

C. Implement ACI Service Graph Two Nodes with GIPo

D. Configure ACI Service Graph with Symmetric PBR

View answer

Correct Answer: A

Question #35

Where is the COOP database located?

A. eaf

B. pine

C. PIC

D. ndpoint

View answer

Correct Answer: B

Question #36

Which components must be configured for the BGP Route Reflector policy to take effect?

A. spine fabric interface overrides and profiles

B. access policies and profiles

C. pod policy groups and profiles

D. leaf fabric interface overrides and profiles

View answer

Correct Answer: C

Question #37

Refer to the exhibit.An engineer configures a Layer 4 to Layer 7 device object. The device is a virtual firewall with a single network adapter and it must be deployed in routed mode. Which action completes the configuration of the device object?

A. Enable Promiscuous Mode

B. Change Function Type to GoTo

C. Change context awareness to Multiple

D. Add an outside interface to the cluster interfaces

View answer

Correct Answer: B

Question #38

Which feature should be disabled on a bridge domain when a default gateway for endpoints is on an external device instead of a Cisco ACI bridge domain SVI?

A. unknown unicast flooding

B. ARP flooding

C. unicast routing

D. proxy ARP

View answer

Correct Answer: C

Question #39

An engineer is creating a configuration import policy that must terminate if the imported configuration is incompatible with the existing system. Which import mode achieves this result?

A. merge

B. atomic

C. best effort

D. replace

View answer

Correct Answer: B

Question #40

A network engineer configured a Cisco ACI fabric as follows:· An EPG called EPG-A is created and associated with a VMM domain called North. · The EPG-A is associated with BD-A and is in an application profile called Apps-A.· The BD-A is associated with VRF-1 in the Prod tenant.Which port group must be selected to place VMs in EPG-A?

A. Prod|Apps-A|EPG-A

B. Prod|Apps-A|North|EPG-A

C. Prod|Business_Apps|BD-A|EPG-A

D. Prod|VRF-1|Apps-A|EPG-A

View answer

Correct Answer: A

Question #41

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #42

A VM called App_1 belongs to VLAN 10. VM App_2 belongs to VLAN 20. Pool_1 contains VLAN 10 and Pool_2 contains VLAN 20. Currently, AP_1 is located on Server 1. The Cisco ACI fabric has these configurations:· The two physical domains are called Phys_1 and Phys_2.· The two VLAN pools are called Pool_1 and Pool_2.· The two AAEPs are called AAEP_1 and AAEP_2.An engineer must replace App_1 with App_2. Which action under the VPC interface policy group accomplishes this goal?

A. Configure Phys_2

B. Map VM App_2

C. Attach AAEP_2

D. Assign Pool_2

View answer

Correct Answer: C

Question #43

Which role do interfaces Ethernet-50 have in this output?

A. leaf fabric ports

B. server fabric ports

C. leaf access ports

D. server uplink ports

View answer

Correct Answer: A

Question #44

An engineer is in the process of discovering a new Cisco ACI fabric consisting of two spines and four leaf switches. The discovery of leaf 1 has just been completed. Which two nodes are expected to be discovered next? (Choose two.)

A. leaf 2

B. leaf 4

C. spine 1

D. leaf 3

E. spine 2

View answer

Correct Answer: CE

Question #45

A network engineer configured a Cisco ACI fabric as follows:· An EPG called EPG-A is created and associated with a VMM domain called North. · The EPG-A is associated with BD-A and is in an application profile called Apps-A.· The BD-A is associated with VRF-1 in the Prod tenant.Which port group must be selected to place VMs in EPG-A?

A. Prod|Apps-A|EPG-A

B. Prod|Apps-A|North|EPG-A

C. Prod|Business_Apps|BD-A|EPG-A

D. Prod|VRF-1|Apps-A|EPG-A

View answer

Correct Answer: A

Question #46

An engineer must connect a new host to porton Leaf 101. A Cisco ACI fabric has an MCP policy configured but experiences excessive Layer 2 loops. The engineer wants the Cisco ACI fabric to detect and prevent Layer 2 loops in the fabric. Which set of actions accomplishes these goals?

A. Enable MCP locally

B. Enable MCP locally

C. Enable MCP globally

D. Enable MCP globally

View answer

Correct Answer: D

Question #47

An engineer wants to monitor all configuration changes, threshold crossing, and link-state transitions in a Cisco ACI fabric. Which action must be taken to receive the required messages?

A. Add Faults and Events to the monitor policy

B. Add Session Logs and Audit Logs to the monitor policy

C. Include Audit Logs and Events in the Syslog source policy

D. Include Events and Session Logs in the Syslog source policy

View answer

Correct Answer: C

Question #48

Refer to the exhibit. An engineer configures connectivity for a bare metal server called SVR-15. EPG-15 is associated with a physical domain named phys_dom-15. The VPC member port is statically bound to EPG-15 with Encapsulation VLAN-1500. Which step must the engineer take to ensure that SVR-15 is connected to the Cisco ACI fabric?

A. Associate an LACP interface policy to phys_dom-15 for VLAN-1500

B. Enable dynamic VLAN assignment for the VLAN pool that is associated with phys_dom-15

C. Configure a VPC explicit protection group for VLAN-1500 on the VPC member ports

D. Confirm that the VLAN pool that is associated with phys_dom-15 includes VLAN-1500

View answer

Correct Answer: D

Question #49

Refer to the exhibit.An engineer configures a Layer 4 to Layer 7 device object. The device is a virtual firewall with a single network adapter and it must be deployed in routed mode. Which action completes the configuration of the device object?

A. Enable Promiscuous Mode

B. Change Function Type to GoTo

C. Change context awareness to Multiple

D. Add an outside interface to the cluster interfaces

View answer

Correct Answer: B

Question #50

A network engineer configured a Cisco ACI fabric as follows:· An EPG called EPG-A is created and associated with a VMM domain called North. · The EPG-A is associated with BD-A and is in an application profile called Apps-A.· The BD-A is associated with VRF-1 in the Prod tenant.Which port group must be selected to place VMs in EPG-A?

A. Prod|Apps-A|EPG-A

B. Prod|Apps-A|North|EPG-A

C. Prod|Business_Apps|BD-A|EPG-A

D. Prod|VRF-1|Apps-A|EPG-A

View answer

Correct Answer: A

Question #51

What does a bridge domain represent?

A. ayer 3 cloud

B. ayer 2 forwarding construct

C. enant

D. hysical domain

View answer

Correct Answer: B

Question #52

Refer to the exhibit. A tenant is configured with a single L3Out and a single-homed link to the core router called Core-1. An engineer must add a second link to the L3Out that connects to the Core-2 router. Which action allows traffic from Core-2 to BL-1002 to have the same connectivity as the traffic from Core-1 to BL-1001?

A. dd a second path to the logical interface profile of the existing L3Out

B. dd a second subnet to the external EPG to the existing L3Out

C. dd a second OSPF interface profile to the logical interface profile

D. dd a second interface to the external domain to the existing L3Out

View answer

Correct Answer: A

Question #53

An ACI administrator notices a change in the behavior of the fabric. Which action must be taken to determine if a human intervention introduced the change?

A. Inspect event records in the APIC UI to see all actions performed by users

B. Inspect /var/log/audit_messages on the APIC to see a record of all user actions

C. Inspect audit logs in the APIC UI to see all user events

D. Inspect the output of show command history in the APIC CLI

View answer

Correct Answer: C

Question #54

What must be enabled in the bridge domain to have the endpoint table learn the IP addresses of endpoints?

A. L2 unknown unicast: flood

B. GARP based detection

C. unicast routing

D. subnet scope

View answer

Correct Answer: C

Question #55

An engineer configures an L3Out in VRF-1 that was configured for Import Route Control Enforcement. The L3Out uses OSPF to peer with a core switch. The L3Out has one external EPG, and it has been configured with a subnet 10.1.0.0/24. Which scope must be set to force10.1.0.0/24 to populate in the routing table for VRF-1?

A. xport Route Control Subnet

B. mport Route Control Subnet

C. xternal Subnet for External EPG

D. hared Route for External EPG

View answer

Correct Answer: B

Question #56

Which feature dynamically assigns or modifies the EPG association of virtual machines based on their attributes?

A. vzAny contracts

B. standard contracts

C. application EPGs

D. uSeg EPGs

View answer

Correct Answer: D

Question #57

An engineer is creating a configuration import policy that must terminate if the imported configuration is incompatible with the existing system. Which import mode achieves this result?

A. erge

B. tomic

C. est effort

D. eplace

View answer

Correct Answer: B

Question #58

What two actions should be taken to deploy a new Cisco ACI Multi-Pod setup? (Choose two.)

A. AConfigure MP-BGP on IPN routers that face the Cisco ACI spines

B. BConnect all spines to the IPN

C. CConfigure anycast RP for the underlying multicast protocol

D. DConfigure the TEP pool of the new pod to be routable across the IPN

E. EIncrease interface MTU for all IPN routers to support VXLAN traffic

View answer

Correct Answer: DE

Question #59

What happens to the traffic flow when the Cisco ACI fabric has a stale endpoint entry for the destination endpoint?

A. he leaf switch does not learn the source endpoint through data plane learning

B. he leaf switch floods the traffic to the endpoint throughout the fabric

C. he leaf switch sends the traffic to the wrong destination leaf

D. he leaf switch drops the traffic that is destined to the endpoint

View answer

Correct Answer: C

Question #60

Refer to the exhibit. Which two components should be configured as route reflectors in the ACI fabric? (Choose two.)

A. Spine1

B. apic1

C. Spine2

D. Leaf1

E. Leaf2

F. apic2

View answer

Correct Answer: AC

Question #61

A Cisco ACI fabric with an ARP packet must ensure detection of silent hosts with an ARP packet. The current bridge domain is configured with hardware proxy and unicast routing. Which step must be taken on the bridge domain to complete the configuration?

A. Set Optimized Flood for L3 Unknown Multicast

B. Enable Flood in the bridge domain for Multi Destination Flooding

C. Set L2 Unknown Unicast to Flood

D. Enable ARP Flooding in the bridge domain

View answer

Correct Answer: D

Question #62

A network engineer configured a Cisco ACI fabric as follows:· An EPG called EPG-A is created and associated with a VMM domain called North. · The EPG-A is associated with BD-A and is in an application profile called Apps-A.· The BD-A is associated with VRF-1 in the Prod tenant.Which port group must be selected to place VMs in EPG-A?

A. Prod|Apps-A|EPG-A

B. Prod|Apps-A|North|EPG-A

C. Prod|Business_Apps|BD-A|EPG-A

D. Prod|VRF-1|Apps-A|EPG-A

View answer

Correct Answer: A

Question #63

Which device is the pervasive gateway shown installed on?

A. MM switch

B. roxy spine switch

C. eaf switch

D. pine switch

View answer

Correct Answer: C

Question #64

A bridge domain for an EPG called "Web Servers" must be created in the Cisco APIC. The configuration must meet these requirements:Only traffic to known MAC addresses must be allowed to reduce noise.The multicast traffic must be limited to the ports that are participating in multicast routing.The endpoints within the bridge domain must be kept in the endpoint table for 20 minutes without anyupdates.Which set of steps configures the bridge domain that satisfies the requirements?

A. Switch L2 Unknown Unicast to Flood

B. Set L2 Unknown Unicast to Hardware Proxy

C. Multicast Destination Flooding should be set to Flood in BD

D. Select the ARP Flooding checkbox

View answer

Correct Answer: B

Question #65

Which description regarding the initial APIC cluster discovery process is true?

A. he APIC uses an internal IP address from a pool to communicate with the nodes

B. very switch is assigned a unique AV by the APIC

C. he APIC discovers the IP address of the other APIC controllers by using Cisco Discovery Protocol

D. he ACI fabric is discovered starting with the spine switches

View answer

Correct Answer: A

DON'T WANT TO MISS A THING?

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE
Get Now

Free Cisco 300-620 DCACI Practice Questions 2026 Part4

View The Updated 300-620 Exam Questions

View Answers after Submission

DON'T WANT TO MISS A THING?

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE Get Now

Free Cisco 300-620 DCACI Practice Questions 2026 Part4

View The Updated 300-620 Exam Questions

View Answers after Submission

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE
Get Now