Huawei H12-931 Exam Sample Questions | SPOTO

SPOTO's latest exam dumps on the homepage, with a 100% pass rate! SPOTO delivers authentic Cisco CCNA, CCNP study materials, CCIE Lab solutions, PMP, CISA, CISM, AWS, and Palo Alto exam dumps. Our comprehensive study materials are meticulously aligned with the latest exam objectives. With a proven track record, we have enabled thousands of candidates worldwide to pass their IT certifications on their first attempt. Over the past 20+ years, SPOTO has successfully placed numerous IT professionals in Fortune 500 companies.

Take other online exams

Question #1

The maximum dispersion tolerance of an OTU board is 800ps/nm. On a G.652 fiber, the dispersion-limited distance can be roughly considered to be?

A. 40KMcorrect

B. 60KM

C. 80KM

D. 10KM

View answer

Correct Answer: A

Question #2

When planning a 1+1 HSB, corresponding planning principles should be followed. Which of the following are not planning principles for HSB?

A. If the protection type is recovery, it is recommended to set the waiting recovery time to 5 to 12 minutes

B. It is recommended to enable reverse switching to prevent invalid RDI switching at the transmitting end due to signal fading

C. It is recommended to set "Alarm reporting mode" to "Protection group reporting only"

D. Although 1+1 HSB has no restrictions on the slots of the IF boards, it is still recommended that the master and backup IF boards be installed in the dual slots

View answer

Correct Answer: B

Question #3

ODUk_PM_AIS alarm is one of the conditions for ODUK_SNCP switching

A. TRUEcorrect

B. FALSE

View answer

Correct Answer: A

Question #4

After replacing the single master control, the new master control software is inconsistent with the previous faulty master control software. Which alarm may be triggered by the network element damage?

A. SWD_PKGVER_MM

B. SWDL_INPROCESS

C. SWDL_CHGMNG_NOMATCHcorrect

D. SWDL_PKG_NOBDSOFT

View answer

Correct Answer: C

Question #5

The following is the network parameter planning of an engineer’s network management server, among which planning is correct? (Multiple choice)

A. Network management server host name: Server123-correct

B. Stand-alone system (Windows) IP address planning: IP address: 129

C. A network server with 2000 equivalent network elements, the planned bandwidth value for managing network elements is 3

D. For a network with 2,000 equivalent network elements, a collection period of 15 minutes, and 7 days of performance data retention, the planned performance database size is 80GBcorrect

View answer

Correct Answer: ABCD

Question #6

Which of the following statements about the reporting of OTUk_BDI alarm is wrong?

A. Only the WDM side port will report OTUk_BDIcorrect

B. The downstream station's corresponding OTU board receives OTUk_AIS

C. The downstream station's corresponding OTU board receives OTUk_TIM

D. The downstream station’s corresponding OTU board receives OTUk_SSF

View answer

Correct Answer: A

Question #7

During the network acceptance test, it was found that OSN 3500 could work normally when connected to an external clock source, and entered the hold state when disconnected from the external clock source. However, the hold state could not last for 24 hours. Which of the following are the possible reasons?

A. The time of accessing the external high-precision clock source is too shortcorrect

B. The clock SSM function is not enabled

C. Clock level setting error 70200

D. The clock crystal oscillator fails and the board needs to be replaced

View answer

Correct Answer: A

Question #8

While expanding the existing network wave distribution system, which of the following performances do not need to be evaluated?

A. PMD parameters of the linkcorrect

B. Optical power of OTU/OA

C. BER of OTU before error correction at the receiving end

D. Optical power flatness at the receiving end (with MCA)

View answer

Correct Answer: A

Question #9

Which of the following is an error in the system OSNR commissioning?

A. Adjust the single wave group first, and then adjust the main line optical powercorrect

B. One of the principles for adjusting the OSNR flatness of the MPIR point system: After the system power is determined, the OSNR flatness of the MPI-R point is tested by a spectrometer

C. The combiner is an M40V board

D. APE automatically adjusts the optical power of each channel to ensure the flat optical power at the receiving end, thereby ensuring the flatness of OSNR

View answer

Correct Answer: A

Question #10

Four network elements A, B, C, and D form a two-fiber bidirectional multiplex section shared protection ring, and there are a large number of PDH services between A and B. One day, the optical fiber between A and B is interrupted. In order to eliminate the R-LOS alarm on the network management system, an engineer performs a self-loop on the optical ports at both ends of the interrupted optical fiber. After 10 minutes by default, what will happen?

A. The service between A and B is interrupted, and the switching alarm disappears

B. The services of A and B are not affected, and the switching alarm does not disappearcorrect

C. The service between A and B is interrupted, and the switching alarm does not disappear

D. The business between A and B is not affected, and the switching alarm disappears

View answer

Correct Answer: B

Question #11

If the instrument transmits data at a frame rate of X and receives data at a frame rate of Y, then packet loss rate = (XY)/X*100%, usually packet loss rate + throughput = 1

A. TRUEcorrect

B. FALSE

View answer

Correct Answer: A

Question #12

Which of the following statements is wrong about the test items of IEEE 1588V2 time protection function?

A. The active and standby states of the clock board and cross-connect board on the OptiX OSN 8800 are related to each other

B. The active and standby states of the clock board and cross-connect board on the OptiX OSN 6800 are related to each other

C. Test the long-term stability of the time performance in PTP synchronization mode

D. For the long-term jitter test of the physical layer synchronization mode, a time analyzer with a GPS receiver is used to observe at the node for more than 8 hours

View answer

Correct Answer: B

Question #13

Regarding the differences between Linux and Solaris operating systems, which of the following statements is wrong?

A. All disks need to be recognized by the operating system, but Solaris needs to be set in the sd

B. Solaris itself only supports UFS hard disk file system; in Linux, there are many disk file systems to choose from, the default is ext3

C. In Solaris, hot-plug devices are managed through cfgadm-

D. Linux comes with the fssnap command for creating and managing file system snapshots

View answer

Correct Answer: D

Question #14

A certain network has 2,250 equivalent network elements of SDH series, 1,000 equivalent network elements of WDM series, and 1,000 equivalent network elements of router series. The customer purchased value-added functions such as SDH end-to-end, WDM end-to-end, and Corba northbound. Regarding this network management deployment plan, which of the following is wrong?

A. Since there are SDH, OTN and router series network elements, it is necessary to install the SDH network element manager, OTN network element manager and router network element manager subsystems

B. The maximum management capacity of the SDH network element manager subsystem is 2500 equivalent network elements, so one SDH network element manager instance needs to be deployed; the maximum management capacity of the router network element manager subsystem is 5000 equivalent network elements, Therefore, a router NE manager instance needs to be deployedcorrect

C. Due to the purchase of SDH end-to-end and WDM end-to-end value-added features, it is necessary to install SDH network management subsystem and OTN network management subsystem; due to the purchase of Corba northbound interface, it is necessary to install Corba northbound subsystem

D. If the OTN series network elements are OSN 6800+OSN 8800T32 (without ASON, the ratio of the two numbers is 1:1), among which OSN 6800 is used as the master subrack, and OSN 8800 is used as the slave subrack

View answer

Correct Answer: B

Question #15

Using the integral method to measure the OSNR value of a 100G signal, the integrated value of the signal power + noise power in the channel interval read from the OSA is 9.68uW, the integrated value of the noise power in the channel interval is 29.58nW, and the signal center frequency is 0.1nm. The integrated power within is 7.395nW, then the OSNR value is?

A. 10log [(9

B. 10log [(9

C. 10log [(9

D. 10log [(9

View answer

Correct Answer: A

Question #16

The IP address you use is 165.247.52.119, and the subnet mask is 255.255.240.0. Which subnet is your host on?

A. 165

B. 165

C. 165

D. 165

View answer

Correct Answer: D

Question #17

Back-to-back OTM sites, three new relay wavelengths are added. The schematic diagram is as follows. Which of the following statements is wrong?

A. No impact on OTM site up and down services

B. The input optical power of the optical amplifier board does not need to be adjusted

C. No further adjustment is required for the VOA on the relay wavelengthcorrect

D. The VOA of the upper wave does not need to be adjusted

View answer

Correct Answer: C

Question #18

What are the main modules of Huawei RTN 900 series equipment? (multiple choice)

A. GPS

B. IF cable

C. Antenna

D. ODU

E. IDU

View answer

Correct Answer: BCDE

Question #19

During the downgrading process of the smart service, the intermediate node is reset, and the downstream node will have?

A. Signaling residuecorrect

B. Slot Reservation Residual

C. Slot inconsistency remains

View answer

Correct Answer: A

Question #20

Which of the following are commonly used test instruments for WDM system include? (Multiple choice)

A. Optical power metercorrect

B. Optical Spectrum Analyzercorrect

C. Optical Time Domain Reflectometercorrect

D. Data Service Testercorrect

E. 2M BER tester

F. Multimetercorrect

View answer

Correct Answer: ABCDF

Question #21

In what order do the downstream signals flow through the functional blocks of the SL16 circuit board?

A. SPI, RSE, MST, MSP, MSA, HPTcorrect

B. HPT, MSA, MST, RST, SPI

C. SPL, MST, RST, MSP, MSA, HPT

D. HPI, MSP, MSA, MST, RST, SPI

View answer

Correct Answer: A

Question #22

Which of the following are not precautions for the preliminary test?

A. Before the test, check whether the required test lines are complete, the type of connector and the applicability of the instrument, and whether the connection is good

B. Prepare cotton swabs and alcohol, and pay attention to the cleanliness of the connectors at all times during the optical interface characteristic test to ensure the accuracy of the test data

C. Be careful not to look directly at the optical sending interface during the test, so as not to damage the eyes

D. During the 24-hour bit error test, it should be ensured that the entire test process is free from external interference (including human factors and power conditions, etc

View answer

Correct Answer: D

Question #23

The IP address you use is 165.247.52.119, the subnet mask is 255.255.240.0, which subnet is your host on?

A. 165

B. 165

C. 165

D. 165

View answer

Correct Answer: D

Question #24

It is known that the GE optical interface technical indicators of a certain PTN equipment are as follows: average transmit optical power (dBm): -5~0, receive sensitivity (dBm): -23, minimum overload point (dBm): -3, minimum extinction ratio (dB): 9. For this optical interface, which of the following optical powers (dBm) is the most suitable received optical power?

A. -3

B. -15correct

C. -5

D. 0

View answer

Correct Answer: B

Question #25

The single-fiber bidirectional optical interface of the PTN equipment distinguishes upstream and downstream business flows based on time slots.

A. TRUE

B. FALSEcorrect

View answer

Correct Answer: B

Question #26

When LOATOA/THA/TOMTOG and other single board services are activated, the client-side interface of this end reports a SYNC alarm. What is the reason?

A. The client-side interface on this end receives light abnormally, and the client-side interface on the other end receives light abnormally

B. The client-side interface on this end receives light normally, but the client-side interface on the other end receives light abnormally

C. The port receives light normally, and the client-side port receives light normally

D. The client-side interface on this end receives light abnormally, while the client-side interface on the other end receives light normallycorrect

View answer

Correct Answer: D

Question #27

In the Linux system, configure an IP address 129.9.1.100 for the network card Eth0, and use which of the following command?

A. ifconfig eth0 129

B. ipconfig 129

C. ipconfig eth0 129

D. ifconfig 129

View answer

Correct Answer: A

Question #28

If the LED on the SCC board of OSN 8800 T32 shows a value of 11, which of the following subrack ID information does it represent?

A. Secondary subrack

B. No

C. No

D. No

View answer

Correct Answer: C

Question #29

Network elements A, B, and C are OSN 3500s that form a chain network. The two AIC stations are connected to routers. The IPR router is connected to the OptiX SDH equipment through the STM-1 POS port. The PAS port also uses 1 and C2 bytes as payload transfer bytes (for carrying services). VC4 services are created from network element A to network element C, and VC4 is passed through network element B. In this case, is there any alarm reported inside the SDH network?

A. No alarmcorrect

B. There is a C2 mismatch alarm

C. There is a J1 mismatch alarm

D. There is a C2 not installed alarm

View answer

Correct Answer: A

Question #30

What network problems can’t QoS solve?

A. Business single width

B. Delay jitter in transmission

C. Packet loss rate

D. Transmission resourcescorrect

View answer

Correct Answer: D

View Answers after Submission

Please submit your email and WhatsApp to get the answers of questions.

Note: Please make sure your email ID and Whatsapp are valid so that you can get the correct exam results.

Email:

Whatsapp/phone number:

DON'T WANT TO MISS A THING?

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE
Get Now

Huawei H12-931 Exam Sample Questions | SPOTO

View Answers after Submission

DON'T WANT TO MISS A THING?

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE Get Now

Huawei H12-931 Exam Sample Questions | SPOTO

View Answers after Submission

Latest Cisco, PMP, AWS, CompTIA, Microsoft Materials on SALE
Get Now