SPOTO CCNP 300-410 ENARSI exam practice tests cover CCNP 300-410 ENARSI exam questions and answers to help you know about the topics of CCNP 300-410 ENARSI exam easily!
Now, this post will contain 10 CCNP 300-410 ENARSI exam practice questions with verified answers. Try now to test yourself!
If you want to pass the CCNP 300-410 ENARSI exam in the 1st try, SPOTO 100% real CCNP 300-410 ENARSI exam dumps are the best study materials for your preparation.
1. An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?
A. sudo maglev-config update
B. sudo maglev install config update
C. sudo maglev reinstall
D. sudo update config install
Answer: A
2. Which security feature can protect DMVPN tunnels?
A. IPsec
B. TACACS+
C. RTBH
D. RADIUS
Answer: A
3. Refer to the exhibit. Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
A. Configure SNMP rw permission in addition to community ciscotest.
B. Modify access list 1 and allow operations subnet in the access list.
C. Modify access list 1 and allow SNMP in the access list.
D. Configure SNMP rw permission in addition to version 1.
E. Configure SNMP rw permission in addition to community ciscotest 1.
Answer: A,B
4. Which statement about MPLS LDP router ID is true?
A. If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
B. The loopback with the highest IP address is selected as the router ID.
C. The MPLS LDP router ID must match the IGP router ID.
D. The force keyword changes the router ID to the specified address without causing any impact.
Answer: B
5. Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?
A.
R1(config)# ip vrf Inet
R1(config-vrf)#interface FastEthernet0/0
R1(config-if)#ip vrf forwarding Inet
B.
R1(config)#router ospf 1 vrf Inet
R1(config-router)#ip vrf forwarding FastEthernet0/0
C. R1(config)#ip vrf Inet FastEthernet0/0
D.
R1(config)# ip vrf Inet
R1(config-vrf)#ip vrf FastEthernet0/0
Answer: A
6. Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
A. It was obtained directly from the next-hop server.
B. Data packets are process switches for this mapping entry.
C. NHRP mapping is for networks that are local to this router.
D. The mapping entry was created in response to an NHRP registration request.
E. The NHRP mapping entry cannot be overwritten.
Answer: A
7. What is a prerequisite for configuring BFD?
A. Jumbo frame support must be configured on the router that is using BFD.
B. All routers in the path between two BFD endpoints must have BFD enabled.
C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.
D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.
Answer: C
8. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Which command should the engineer use to complete this action?
A. show frequency
B. show track
C. show reachability
D. show threshold
Answer: B
9. While troubleshooting connectivity issues to a router, these details are noticed:
– Standard pings to all router interfaces, including loopbacks, are successful.
– Data traffic is unaffected.
– SNMP connectivity is intermittent.
– SSH is either slow or disconnects frequently.
Which command must be configured first to troubleshoot this issue?
A. show policy-map control-plane
B. show policy-map
C. show interface | inc drop
D. show ip route
Answer: A
10. Which statement about IPv6 ND inspection is true?
A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.
Answer: B
In Conclusion
If you want more valid CCNP 300-410 exam practice tests, please contact SPOTO to get more real 300-410 exam questions!
Get Love to Learn Offer to buy real 300-410 exam dumps at a favorable price!
Latest Passing Report-100% pass guarantee
Recommend Cisco exam study materials:
2024 Updated Real Cisco DEVCOR 350-901 Dumps-Free Demo
Attempt 2024 Free CCNA 200-301 Practice Test to Test Yourself
Breakdown of CCIE Enterprise Infrastructure Certification
Good News: Hurry to Book Your CCIE Lab Exam Slot-Limited Seats Available
How to Pass the CCNP Enterprise 350-401 Exam?
How to get valid and real CCNP Enterprise dumps?
Comments