السؤال #1

Why is user authentication being rejected?

A. The TACACS+ server expects “user”, but the NT client sends “domain/user”

B. The TACACS+ server refuses the user because the user is set up for CHAP

C. The TACACS+ server is down, and the user is in the local database

D. The TACACS+ server is down, and the user is not in the local database

عرض الإجابة

اجابة صحيحة: S

السؤال #2

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)

A. Change the mode from mode tunnel to mode transport on R3

B. Remove the crypto isakmp key cisco address 10

C. Configure the crypto isakmp key cisco address 192

D. Configure the crypto isakmp key cisco address 0

E. Change the mode from mode transport to mode tunnel on R2

عرض الإجابة

اجابة صحيحة: B

السؤال #3

What does the imp-null tag represent in the MPLS VPN cloud?

A. Pop the label

B. Impose the label

C. Include the EXP bit

D. Exclude the EXP bit

عرض الإجابة

اجابة صحيحة: C

السؤال #4

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?A.B.

C.

D.

عرض الإجابة

اجابة صحيحة: D

السؤال #5

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?

A. Set the administrative distance 100 under the RIP process on R2

B. Filter the prefix 10

C. Filter the prefix 10

D. Redistribute the directly connected interfaces on R2

عرض الإجابة

اجابة صحيحة: D

السؤال #6

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?

A. An authentication error with the NTP server results in an incorrect timestamp

B. The keyword localtime is not defined on the timestamp service command

C. The NTP server is in a different time zone

D. The system clock is set incorrectly to summer-time hours

عرض الإجابة

اجابة صحيحة: S

السؤال #7

An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?

A. Configure the service timestamps log uptime command in global configuration mode

B. Configure the logging clock synchronize command in global configuration mode

C. Configure the service timestamps log datetime localtime command in global configuration mode

D. Make sure that the clock on the device is synchronized with an NTP server

عرض الإجابة

اجابة صحيحة: D

السؤال #8

An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?

A. By default, only internal routes and external type 1 routes are redistributed into BGP

B. Only classful networks are redistributed from OSPF to BGP

C. BGP convergence is slow, so the route will eventually be present in the BGP table

D. By default, only internal OSPF routes are redistributed into BGP

عرض الإجابة

اجابة صحيحة: A

السؤال #9

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?

A. Start-time 00:00

B. Start-time 0

C. Start-time immediately

D. Start-time now

عرض الإجابة

اجابة صحيحة: A

السؤال #10

An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?

A. no ip ssh disable

B. ip ssh enable

C. ip ssh version 2

D. crypto key generate rsa

عرض الإجابة

اجابة صحيحة: S

السؤال #11

A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

A. service timestamps log uptime

B. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00

C. service timestamps log datetime localtime show-timezone

D. clock calendar-valid

عرض الإجابة

اجابة صحيحة: D

السؤال #12

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients

B. Route reflector setup requires full IBGP mesh between the routers

C. In route reflector setup, only classful prefixes are advertised to other clients

D. In route reflector setups, prefixes are not advertised from one client to another

عرض الإجابة

اجابة صحيحة: S

السؤال #13

Refer to the exhibits. Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two commands are missing? (Choose two.)

A. The ip nhrp redirect command is missing on the spoke routers

B. The ip nhrp shortcut command is missing on the spoke routers

C. The ip nhrp redirect command is missing on the hub router

D. The ip nhrp shortcut command is missing on the hub router

E. The ip nhrp map command is missing on the hub router

عرض الإجابة

اجابة صحيحة: AD

السؤال #14

Why is the remote NetFlow server failing to receive the NetFlow data?

A. The flow exporter is configured but is not used

B. The flow monitor is applied in the wrong direction

C. The flow monitor is applied to the wrong interface

D. The destination of the flow exporter is not reachable

عرض الإجابة

اجابة صحيحة: A

السؤال #15

Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)

A. Configure SNMP rw permission in addition to community ciscotest

B. Modify access list 1 and allow operations subnet in the access list

C. Modify access list 1 and allow SNMP in the access list

D. Configure SNMP rw permission in addition to version 1

E. Configure SNMP rw permission in addition to community ciscotest 1

عرض الإجابة

اجابة صحيحة: D

السؤال #16

An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?

A. Enter the transport input ssh configuration command

B. Enter the terminal monitor exec command

C. Enter the logging console debugging configuration command

D. Enter the aaa new-model configuration command

عرض الإجابة

اجابة صحيحة: D

السؤال #17

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?

A. debug ip flow

B. debug ip sla error

C. debug ip routing

D. debug ip packet

عرض الإجابة

اجابة صحيحة: B

السؤال #18

What is the result of applying this configuration?

A. The router can form BGP neighborships with any other device

B. The router cannot form BGP neighborships with any other device

C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”

D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”

عرض الإجابة

اجابة صحيحة: B

السؤال #19

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?

A. Add the aaa authentication login default none command to the global configuration

B. Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command

C. Add the aaa authentication login default group tacacs+ local-case command to the global configuration

D. Add the login authentication Console command to the line configuration

عرض الإجابة

اجابة صحيحة: A

السؤال #20

Which subnet is redistributed from EIGRP to OSPF routing protocols?

A. 10

B. 10

C. 10

D. 10

عرض الإجابة

اجابة صحيحة: D

السؤال #21

While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?

A. The device must be resynced to Cisco DNA Center

B. The software image for the device is in install mode

C. The device has lost connectivity to Cisco DNA Center

D. The software image for the device is in bundle mode

عرض الإجابة

اجابة صحيحة: B

السؤال #22

While troubleshooting connectivity issues to a router, these details are noticed: Standard pings to all router interfaces, including loopbacks, are successful. Data traffic is unaffected. SNMP connectivity is intermittent. SSH is either slow or disconnects frequently. Which command must be configured first to troubleshoot this issue?

A. show policy-map control-plane

B. show policy-map

C. show interface | inc drop

D. show ip route

عرض الإجابة

اجابة صحيحة: C

السؤال #23

Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

A. Issue the eigrp stub command on R1

B. Issue the no eigrp stub command on R1

C. Issue the eigrp stub command on R2

D. Issue the no eigrp stub command on R2

عرض الإجابة

اجابة صحيحة: B

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان

عرض الإجابات بعد التقديم

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع! احصل الان

عرض الإجابات بعد التقديم

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان