لا تريد أن تفوت شيئا؟

نصائح اجتياز امتحان الشهادة

آخر أخبار الامتحانات ومعلومات الخصم

برعاية وحديثة من قبل خبرائنا

نعم، أرسل لي النشرة الإخبارية

خذ اختبارات أخرى عبر الإنترنت
السؤال #1
The following is a partial output of the show interfaces command: What does the Serial 0 is up, line protocol is down statement signify in the output? (Choose all that apply.)
A. the shutdown interface command is present in the router configuration
B. a cable is unplugged
C. the interface is displaying normal operation
D. there are no problems with physical connectivity
E. there is a configuration problem in the local or remote router
عرض الإجابة
اجابة صحيحة: DE
السؤال #2
A network engineer is connected via wireless to a Cisco AireOS WLC and wants to download the configuration but is unable to do so. Which change will correct the issue?
A. enable management via wireless
B. connect via wired network
C. enable Telnet
D. enable WebAuth SecureWeb
E. connect on 5-GHz SSID
عرض الإجابة
اجابة صحيحة: B
السؤال #3
Which protocol is responsible for negotiating and maintaining Point-to-Point Protocol (PPP) connections?
A. LCP
B. NCP
C. BRI
D. ISDN
عرض الإجابة
اجابة صحيحة: A
السؤال #4
Which device creates broadcast domains and enables communication across separate broadcast domains?
A. router
B. switch
C. hub
D. access points
عرض الإجابة
اجابة صحيحة: A
السؤال #5
Which Cisco Internetwork Operating System (IOS) command is used to view information about Open Shortest Path First (OSPF) routing processes?
A. show ip ospf database
B. show ip ospf statistics
C. show ip ospf
D. show ip ospf traffic
عرض الإجابة
اجابة صحيحة: C
السؤال #6
You have added a new router to your network using all of the default settings. You can connect to everything by IP address, but the router doesn't seem to be resolving names to IP addresses. The DNS server is in a directly connected network. Which of the following is most likely the problem?
A. You configured an incorrect IP address for the DNS server
B. You configured an incorrect default gateway on the router
C. You failed to execute the ip domain lookup command
D. You failed to create an IP helper address
عرض الإجابة
اجابة صحيحة: A
السؤال #7
Which Cisco IOS command would prompt for input in the following format?
A. ping 10
B. ping
C. traceroute
D. tracert
عرض الإجابة
اجابة صحيحة: B
السؤال #8
Which of the following splits the network into separate broadcast domains?
A. bridges
B. VLANs
C. switches
D. hubs
عرض الإجابة
اجابة صحيحة: B
السؤال #9
You are the network administrator for your company. You wanted to connect the host computers to the switches. Which cable should you use to ensure the connectivity?
A. Straight-through cable
B. Rollover cable
C. Crossover cable
D. Serial cable
عرض الإجابة
اجابة صحيحة: A
السؤال #10
WLC1 becomes unresponsive due to a power failure at a customer site. How does the access point that is shown in the WLC controller GUI behave now that WLC1 is disabled?
A. associates to controller 10
B. associates to controller 10
C. associates to controller 10
D. associates to controller 10
عرض الإجابة
اجابة صحيحة: B
السؤال #11
A customer cannot access the GUI on the Cisco 5508 Wireless Controller from the management interface due to network failure. Which interface can the customer use to access the WLC GUI until the network issues are resolved?
A. virtual
B. dynamic
C. console port
D. service port
عرض الإجابة
اجابة صحيحة: D
السؤال #12
Which of the following statements are NOT part of the guidelines for configuring VLAN Trunking Protocol (VTP) to ensure that VLAN information is distributed to all Cisco switches in the network? (Choose all that apply.)
A. The VTP version must be the same on all switches in a VTP domain
B. The configuration revision number must be configured identically on all switches in a VTP domain
C. The VTP password must be the same on all switches in a VTP domain
D. The VTP domain name must be the same on all switches in a VTP domain
E. VLANs configured on clients should exist on the server switch
F. The switch(s) that will share VLAN information is(are) operating in VTP server mode
G. The switches must be configured to use the same method of VLAN tagging
H. The switches must be connected with trunk links
عرض الإجابة
اجابة صحيحة: BE
السؤال #13
An engineer is trying to convert the IP Address of the wireless controller to amend DHCP Option 43 configuration on the DHCP server. What mathematical format must the IP address of the Wireless controller be converted to in order to function correctly?
A. Hexadecimal
B. Binary
C. Decimal
D. ASCII
عرض الإجابة
اجابة صحيحة: A
السؤال #14
How many collision and broadcast domains are in the network shown below?
A. 4 collision domains and 3 broadcast domains
B. 7 collision domains and 2 broadcast domainsC
D. 6 collision domains and 2 broadcast domains
عرض الإجابة
اجابة صحيحة: B
السؤال #15
A customer is using central web authentication with a Cisco 5508 Wireless Controller and Cisco Identity Services Engine. An error occurs when wireless clients are redirected to the hosted splash page. What is causing the client error?
A. Secure Web Mode is disabled on the WLC
B. OCSP is disabled on the WLC
C. Management Via Dynamic Interface is disabled on the WLC
D. Ethernet Multicast Forwarding is enabled on the WLC
عرض الإجابة
اجابة صحيحة: A
السؤال #16
What is the term used for the Ethernet communication mechanism by which hosts can send and receive data simultaneously?
A. full-duplex
B. multiplex
C. half-duplex
D. duplex
عرض الإجابة
اجابة صحيحة: A
السؤال #17
Which command would you use to see which interfaces are currently operating as trunks?
A. show interface switchports
B. show trunk interface
C. show interfaces trunk
D. show switchport trunk
عرض الإجابة
اجابة صحيحة: C
السؤال #18
What is the default Administrative Distance (AD) value for an Enhanced Interior Gateway Routing Protocol (EIGRP) summary route?
A. 1
B. 5
C. 90
D. 20
عرض الإجابة
اجابة صحيحة: B
السؤال #19
The following shows the partial output of the show cdp neighbors command: DevicID Local Intrfce Holdtme Capability Platform Port ID lab-7206 Eth 0 157 R 7206VXR Fas 0/0/0 lab- as5300-1 Eth 0 163 R AS5300 Fas 0 lab-as5300- 2 Eth 0 159 R AS5300 Eth 0 lab-as5300-3 Eth 0 122 R AS5300 Eth 0 lab-as5300-4 Eth 0 132 R AS5300 Fas 0/0 lab-3621 Eth 0 140 R S 3631- telcoFas 0/0 008024 2758E0 Eth 0 132 T CAT3000 1/2 lab-400-1 Eth 0 130 r FH400 Fas 0/0 What does "r" represent in this output?
A. Router
B. Route bridge
C. Hub
D. Repeater
عرض الإجابة
اجابة صحيحة: D
السؤال #20
Which two statements are TRUE of default routes? (Choose two.)
A. Default routes are used for routing packets destined only for networks that are listed in the routing table
B. Default routes are used for routing packets destined for networks that are not listed in the routing table
C. Default routes should not be used in a stub network
D. Default routes are ideal for use in stub networks
E. Network security is increased by using default routes
عرض الإجابة
اجابة صحيحة: BD
السؤال #21
You are configuring all your devices for IPv6. Which of the following is the only device that requires the ipv6 unicast-routing command?
A. Layer 2 switch
B. Router
C. Adaptive security appliance
D. Wireless AP
عرض الإجابة
اجابة صحيحة: B
السؤال #22
You have multiple departments sharing a common network. You are concerned about network traffic from one department reaching another department. What would be a solution for isolating the departments? (Choose all that apply.)
A. Configure separate VLANs for each department
B. Assign a unique VTP domain for each department
C. Put each department in a separate collision domain
D. Configure trunk links between departmental switches
E. Configure separate subnets for each department
عرض الإجابة
اجابة صحيحة: AE
السؤال #23
A customer has completed the installation of an 802.11ac greenfield deployment at their corporate headquarters. They would like to leverage 802.11ac enhanced speeds on the trusted employee WLAN. In order to configure the employee WLAN, what Layer 2 security policies are valid?
A. WPA2 (TKIP)
B. WPA(AES)
C. OPEN
D. WEP
عرض الإجابة
اجابة صحيحة: C
السؤال #24
The workstation at 10.0.1.3 sends a packet to the workstation at 10.1.1.3. When the packet leaves the R2 router, what addresses will be located in the header? (Choose two.)
A. Source MAC bb
B. Source MAC dd
C. Source MAC ee
D. Source IP 10
E. Source IP 10
F. Source IP 10
G. Source IP 10
عرض الإجابة
اجابة صحيحة: BD
السؤال #25
When deploying a Cisco Cloud Wireless Infrastructure, what two destination ports must be open? (Choose two.)
A. TCP/5246
B. UDP/5246
C. TCP/5247
D. UDP/5247
E. TCP/7351
F. UDP/7351
G. TCP/7734
H. UDP/7734
عرض الإجابة
اجابة صحيحة: FG
السؤال #26
Which interface is used to connect the foreign and anchor controllers?
A. management
B. service
C. virtual
D. dynamic
عرض الإجابة
اجابة صحيحة: A
السؤال #27
What is the significance of the 1 in the following configuration? router(config)# router eigrp 1
A. It is the process ID for EIGRP and is locally significant to this router
B. It is the process ID for EIGRP and must be the same on all EIGRP routers
C. It is the AS number for EIGRP and is locally significant to this router
D. It is the AS number for EIGRP and must be the same on all EIGRP routers
عرض الإجابة
اجابة صحيحة: D
السؤال #28
A network administrator is attempting to connect to the GUI of a WLC with interfaces as shown. Which IP address should the network administrator use?
A. 192
B. 192
C. 192
D. 192
E. 192
عرض الإجابة
اجابة صحيحة: B
السؤال #29
A customer has ordered a Cisco 5760 Wireless Controller. What speed and quantity of ports are needed for full-speed operation?
A. 6 x 1 Gb
B. 6 x 10 Gb
C. 2 x 10 Gb
D. 2 x 1 Gb
E. 8 x 1 Gb
F. 8 x 10 Gb
عرض الإجابة
اجابة صحيحة: B
السؤال #30
Which command is used on the Cisco Catalyst 2950 series switch to configure a port as a VLAN trunk port?
A. switchport mode trunk
B. set trunk on
C. switchport trunk on
D. trunk mode on
عرض الإجابة
اجابة صحيحة: A
السؤال #31
A customer wants to deploy a mesh network with 2 root access points and 10 mesh access points. The root access points should be configured as which mode on the WLC?
A. mesh
B. FlexConnect
C. bridge
D. rouge detection
E. sniffer
عرض الإجابة
اجابة صحيحة: C
السؤال #32
You need to set the Telnet password to "john" on a Cisco router. Which set of commands would you use?
A. Router(config)#line vty 0 4 Router(config-line)#login Router(config-line)#password john
B. Router(config)#line con 0 Router(config-line)#login Router(config-line)#password john
C. Router(config)#line vty 0 4 Router(config-line)#login Router(config-line)#enable secret john
D. Router(config)#line con 0 Router(config-line)#login Router(config-line)#enable password john
عرض الإجابة
اجابة صحيحة: A
السؤال #33
Which Network Address Translation (NAT) term is used for the IP address that is assigned to a host on the inside network?
A. Inside local address
B. Inside global address
C. Outside local address
D. Outside global address
عرض الإجابة
اجابة صحيحة: A
السؤال #34
Which of the following protocols is responsible for negotiating upper-layer protocols that will be carried across a Point-to-Point Protocol (PPP) connection?
A. LCP
B. NCP
C. LMI
D. ISDN
عرض الإجابة
اجابة صحيحة: B
السؤال #35
Which Cisco IOS command would produce the following output?
A. show ip interface
B. show ip interface brief
C. show interfaces
D. show interface brief
عرض الإجابة
اجابة صحيحة: C
السؤال #36
You are a network administrator for your organization. Your organization has two Virtual LANs (VLANs) named Marketing and Production. All switches in the network have both VLANs configured on them. Switches A, C, F, and G have user machines connected for both VLANs, while switches B, D, and E have user machines connected for the Production VLAN only. (Click the Exhibit(s) button to view the network diagram.) To reduce broadcast traffic on the network, you want to ensure that broadcasts from the Marketing VL
A. PVST
B. RSTP
C. VTP Pruning
D. Dynamic VLANs
عرض الإجابة
اجابة صحيحة: C
السؤال #37
You have executed the following commands on a switch: Switch64(config)# interface range gigabitethernet2/0/1 -2 Switch64(config-if-range)# switchport mode access Switch64(config-if-range)# switchport access vlan 10 Switch64(config-if-range)# channel-group 5 mode auto In which of the following situations will Switch64 create an Etherchannel?
A. If the other switch is set for desirable mode
B. If the other switch is set for auto mode
C. If the other switch is set for on mode
D. If the other switch is set for passive mode
عرض الإجابة
اجابة صحيحة: A
السؤال #38
An engineer is configuring a SSID to utilize the management interface on the WLC. The management interface is configured with an untagged VLAN in the wireless controller interface settings. The controller is connected to a neighboring switch via the interface shown in the diagram. Which VLAN will traffic coming from the newly created SSID use to traverse the wired network?
A. 1
B. 20
C. 44
D. 50
عرض الإجابة
اجابة صحيحة: C
السؤال #39
Which feature is NOT provided by flow control?
A. buffering
B. windowing
C. full duplex transmission
D. source-quench messaging
عرض الإجابة
اجابة صحيحة: C
السؤال #40
What command produced the following output?
A. show ip process
B. show ip route
C. show ip protocols
D. show ip routing process
عرض الإجابة
اجابة صحيحة: C

عرض الإجابات بعد التقديم

يرجى إرسال البريد الإلكتروني الخاص بك والواتس اب للحصول على إجابات الأسئلة.

ملحوظة: يرجى التأكد من صلاحية معرف البريد الإلكتروني وWhatsApp حتى تتمكن من الحصول على نتائج الاختبار الصحيحة.

بريد إلكتروني:
رقم الواتس اب/الهاتف:


Copyright © 2024. Designer by SPOTO Official Website. All Rights Reserved.