لا تريد أن تفوت شيئا؟

نصائح اجتياز امتحان الشهادة

آخر أخبار الامتحانات ومعلومات الخصم

برعاية وحديثة من قبل خبرائنا

نعم، أرسل لي النشرة الإخبارية

خذ اختبارات أخرى عبر الإنترنت

السؤال #1
DRAG DROP Drag and drop the commands from the left onto the correct categories on the right. Select and Place:
A. Mastered
B. Not Mastered
عرض الإجابة
اجابة صحيحة: A
السؤال #2
HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?
A. Configure preempt on one of the switches in the HSRP group
B. Configure the same HSRP priority between the two switches
C. Configure the correct subnet mask on Nexus7K-1
D. Configure HSRP version 2 on Nexus7K-2
عرض الإجابة
اجابة صحيحة: D
السؤال #3
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?
A. Modify the VLAN assignment to vNICs
B. Change the PIN groups on the vHBAs
C. Modify the FCoE VLAN
D. Set the FCoE VLAN as the native VLAN on server uplinks
عرض الإجابة
اجابة صحيحة: A
السؤال #4
After the configuration is performed, guestshell continues to use 2%CPU. Which action resolves the issue?
A. Resync the database
B. Recreate the guestshell
C. Reboot the guestshell
D. Reboot the switch
عرض الإجابة
اجابة صحيحة: A
السؤال #5
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one- by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?
A. The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1
B. Rebooting the APICs and the leaf and spine switches after wiping them is not required
C. You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1
D. The same Fabric Name value should be used before after wiping all devices
عرض الإجابة
اجابة صحيحة: C
السؤال #6
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?
A. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
B. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
C. shell=Security_Domain_1/Read_Role_1|Read_Role_2
D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2
عرض الإجابة
اجابة صحيحة: C
السؤال #7
A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)
A. Configure the NVE interfaces to be Up on both switches
B. Set a different distributed gateway virtual MAC address
C. Set a different secondary IP addresses on NVE source-interface
D. Configure the same VNI to multicast group maping
E. Set a different primary IP addresses on NVE source-interface
عرض الإجابة
اجابة صحيحة: AD
السؤال #8
After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.)
A. Configure the local vPC role priority to have a lower value than Switch-A
A. Configure the local vPC role priority to have a higher value than Switch-A
B. Disable and then re-enable the vPC peer-keepalive link
C. Configure the local vPC role priority to have the same value as Switch-A
D. Disable and then re-enable the vPC peer link
عرض الإجابة
اجابة صحيحة: BE
السؤال #9
A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?
A. Enable the auto-learning feature
B. Use the force option to identify rejected devices
C. Find conflicting entries between the active and configuration databases
D. Verify that devices are fully attached to the active database
عرض الإجابة
اجابة صحيحة: A

عرض الإجابات بعد التقديم

يرجى إرسال البريد الإلكتروني الخاص بك والواتس اب للحصول على إجابات الأسئلة.

ملحوظة: يرجى التأكد من صلاحية معرف البريد الإلكتروني وWhatsApp حتى تتمكن من الحصول على نتائج الاختبار الصحيحة.

بريد إلكتروني:
رقم الواتس اب/الهاتف: