السؤال #1

A kurtosis of -1,2754 indicates?

A. Platykurtic (flat with a short tail)

B. Leptokurtic (peaked with long tails)

C. Multi-modal (more than one distribution)

D. Kanban Model

عرض الإجابة

اجابة صحيحة: A

السؤال #2

The use of station warning lights, tool boards and jidohka devices in the application of Lean accomplish which of these principles?

A. Pilferage Minimization

B. Visual Factory

C. Management Awareness

D. Operator Attentiveness

عرض الإجابة

اجابة صحيحة: B

السؤال #3

Select all the statements that are true after reviewing the Capability Analysis shown here. (Note:There are 4 correct answers).

A. The process is out of Control

B. The process is properly assumed to be a Normal process

C. The Mean of the process moving range is 1

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: BCDE

السؤال #4

A periodic time frame can be used to arrange for Control Limit and Center Line calculations with good SPC implementation in a process.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #5

A Lean Principle that addresses efficiency by the process worker is called ____________________?

A. Visual Factory

B. Supervising

C. Training

D. Standardizing

عرض الإجابة

اجابة صحيحة: D

السؤال #6

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #7

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #8

Select all the statements that are true after reviewing the Capability Analysis shown here. (Note:There are 4 correct answers).

A. The process is out of Control

B. The process is properly assumed to be a Normal process

C. The Mean of the process moving range is 1

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: BCDE

السؤال #9

Measurement error is defined as the effect of all sources of measurement variability that caused an observed or measured value to deviate from the __________.

A. tandard Deviation

B. edian

C. rue value

D. ean

عرض الإجابة

اجابة صحيحة: C

السؤال #10

__________ Distributions occur when data comes from several sources that are supposed to be the same yet are not.

A. Skewed

B. Bimodal

C. Gaussian

D. Tri-peaked

عرض الإجابة

اجابة صحيحة: A

السؤال #11

After reviewing the Capability Analysis shown here select the statement(s) that are untrue.

A. The process is properly assumed to be a Normal process

B. The Mean of the process moving range is 1

C. The process is out of Control

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: A

السؤال #12

The use of Kanbans work best with pull systems for determining the timing of which products or services are produced.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #13

A primary benefit of using a Multi-Vari Chart is it provides a visual presentation of two-way interactions.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #14

The use of station warning lights, tool boards and jidohka devices in the application of Lean accomplish which of these principles?

A. Pilferage Minimization

B. Visual Factory

C. Management Awareness

D. Operator Attentiveness

عرض الإجابة

اجابة صحيحة: B

السؤال #15

Which of these are correct if Cpk Upper is 2.0 and Cpk Lower is 1.0?

A. The process is not stable

B. The process is shifted to the left

C. Cpk must be reported as 1

D. The process Mean is 1

عرض الإجابة

اجابة صحيحة: C

السؤال #16

After a Belt has put data through the smoothing process which chart would be used to look for trends in the data?

A. AMoving Average Chart

B. BMulti-Vari Chart

C. CX bar Chart

D. DPareto Chart

عرض الإجابة

اجابة صحيحة: A

السؤال #17

Lean Six Sigma's general approach to solving significant challenges related to a process is called _________________.

A. DOE

B. SIPOC

C. DMAIC

D. FMEA

عرض الإجابة

اجابة صحيحة: C

السؤال #18

A primary benefit of using a Multi-Vari Chart is it provides a visual presentation of two-way interactions.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #19

Which statement(s) are true about the Fitted Line Plot shown here? (Note: There are 2 correct answers).

A. When Reactant increases, the Energy Consumed increases

B. The slope of the equation is a positive 130

C. The predicted output Y is close to -18 when the Reactant level is set to 6

D. Over 85 % of the variation of the Energy Consumed is explained by the Reactant via this Linear Regression

عرض الإجابة

اجابة صحيحة: CD

السؤال #20

If a Histogram displays two peaks the distribution would likely be _____________.

A. Transformed

B. Multi-skewed

C. Bimodal

D. Bi-attribute

عرض الإجابة

اجابة صحيحة: C

السؤال #21

A Belt will occasionally do a quick experiment referred to as an OFAT which stands for____________________.

A. nly a Few Are Tested

B. pposite Factors Affect Technique

C. ne Factor At a Time

D. rdinary Fractional Approach Technique

عرض الإجابة

اجابة صحيحة: C

السؤال #22

Select all the statements that are true after reviewing the Capability Analysis shown here. (Note:There are 4 correct answers).

A. The process is out of Control

B. The process is properly assumed to be a Normal process

C. The Mean of the process moving range is 1

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: BCDE

السؤال #23

SPC on the outputs is more preferred than SPC on the inputs when implementing SPC for your process.

A. True

B. False

عرض الإجابة

اجابة صحيحة: B

السؤال #24

__________ Distributions occur when data comes from several sources that are supposed to be the same yet are not.

A. Skewed

B. Bimodal

C. Gaussian

D. Tri-peaked

عرض الإجابة

اجابة صحيحة: A

السؤال #25

A Belt will occasionally do a quick experiment referred to as an OFAT which stands for ____________________.

A. Only a Few Are Tested

B. Opposite Factors Affect Technique

C. One Factor At a Time

D. Ordinary Fractional Approach Technique

عرض الإجابة

اجابة صحيحة: C

السؤال #26

The 80:20 rule is associated with which of these tools?

A. raming Tool

B. areto Chart

C. IPOC

D. imon's Cross-Functional Tool

عرض الإجابة

اجابة صحيحة: B

السؤال #27

Which statement(s) describe an undesirable situation when implementing SPC?

A. The lower Control Limit for the R chart is equal to zero

B. Attempt to use SPC for tracking transaction times at a warehouse

C. A process is in Statistical Control before implementation of SPC

D. The Control Limits are wider than the customer specification limits

عرض الإجابة

اجابة صحيحة: D

السؤال #28

Select all the statements that are true after reviewing the Capability Analysis shown here. (Note:There are 4 correct answers).

A. The process is out of Control

B. The process is properly assumed to be a Normal process

C. The Mean of the process moving range is 1

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: BCDE

السؤال #29

If a process has Outliers which pair of charts is most preferable if subgroups will exist for the Continuous Data?

A. Individual--Moving Range

B. Xbar-R Charts

C. Xbar-S Charts

D. nP and P Charts

عرض الإجابة

اجابة صحيحة: B

السؤال #30

A primary benefit of using a Multi-Vari Chart is it provides a visual presentation of two-way interactions.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #31

__________ Distributions occur when data comes from several sources that are supposed to be the same yet are not.

A. Skewed

B. Bimodal

C. Gaussian

D. Tri-peaked

عرض الإجابة

اجابة صحيحة: A

السؤال #32

When a Belt applies the practice of Poka-Yoke to a project challenge she is attempting to make certain the activity is _______________ .

A. Well documented

B. Removed from the line

C. Mistake proofed

D. Highly visible

عرض الإجابة

اجابة صحيحة: C

السؤال #33

Fractional Factorial designs for an experimental approach are used when ____________ about the multiple metric interaction in a process.

A. Much is known

B. Little is known

C. We don't care

D. Data exists

عرض الإجابة

اجابة صحيحة: B

السؤال #34

After a Belt has put data through the smoothing process which chart would be used to look for trendsin the data?

A. oving Average Chart

B. ulti-Vari Chart

C. bar Chart

D. areto Chart

عرض الإجابة

اجابة صحيحة: A

السؤال #35

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #36

A Six Sigma tool that helps to screen factors by using graphical techniques to logically subgroup multiple discrete X's plotted against a continuous Y is known as a _____________Chart.

A. SIPOC

B. Multi-Vari

C. Box Plot

D. Whisker

عرض الإجابة

اجابة صحيحة: B

السؤال #37

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #38

A Lean Principle that addresses efficiency by the process worker is called ____________________?

A. Visual Factory

B. Supervising

C. Training

D. Standardizing

عرض الإجابة

اجابة صحيحة: D

السؤال #39

The data on SPC charts are typically constructed such that they have the most recent data point on the right hand side.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #40

For the data shown here a Belt suspects the three grades are supplying the same results. Which statement(s) are true for proper Hypothesis Testing?

A. n appropriate test to test Central Tendency is the Mood's Median test

B. he most appropriate Central Tendency to test is the Means

C. n appropriate test to test Central Tendency is the ANOVA test

D. n appropriate test to test Central Tendency is the Levene's test

عرض الإجابة

اجابة صحيحة: A

السؤال #41

Select all the statements that are true after reviewing the Capability Analysis shown here. (Note:There are 4 correct answers).

A. The process is out of Control

B. The process is properly assumed to be a Normal process

C. The Mean of the process moving range is 1

D. This Capability Analysis used subgroups

E. Majority of the dimensional values are outside of the tolerance than within

عرض الإجابة

اجابة صحيحة: BCDE

السؤال #42

Bias in Sampling is an error due to lack of independence among random samples or due to systematic sampling procedures.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #43

A primary benefit of using a Multi-Vari Chart is it provides a visual presentation of two-way interactions.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #44

When a Belt applies the practice of Poka-Yoke to a project challenge she is attempting to make certain the activity is _______________ .

A. Well documented

B. Removed from the line

C. Mistake proofed

D. Highly visible

عرض الإجابة

اجابة صحيحة: C

السؤال #45

A primary benefit of using a Multi-Vari Chart is it provides a visual presentation of two-way interactions.

A. True

B. False

عرض الإجابة

اجابة صحيحة: A

السؤال #46

__________ Distributions occur when data comes from several sources that are supposed to be the same yet are not.

A. Skewed

B. Bimodal

C. Gaussian

D. Tri-peaked

عرض الإجابة

اجابة صحيحة: A

السؤال #47

__________ Distributions occur when data comes from several sources that are supposed to be the same yet are not.

A. Skewed

B. Bimodal

C. Gaussian

D. Tri-peaked

عرض الإجابة

اجابة صحيحة: A

السؤال #48

When it comes to Control one of the most effective means of eliminating defects is to _________________ .

A. Train personnel often and thoroughly

B. Keep a Six Sigma project going on the process at all times

C. Design defect prevention into the product

D. Have each process consist of no more than five steps

عرض الإجابة

اجابة صحيحة: C

السؤال #49

One of the metrics commonly used in Lean Six Sigma is DPU. This acronym stands for ___________________.

A. Deferred planned usage

B. Defects per unit

C. Decreased production utilization

D. Downtime per unit

عرض الإجابة

اجابة صحيحة: B

السؤال #50

Which statement(s) are correct for the Regression Analysis shown here? (Note: There are 2 correct answers).

A. This Regression is an example of a Multiple Linear Regression

B. This Regression is an example of Cubic Regression

C. %Cu explains the majority of the process variance in heat flux

D. Thickness explains over 80% of the process variance in heat flux

E. The number of Residuals in this Regression Analysis is 26

عرض الإجابة

اجابة صحيحة: AD

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان

عرض الإجابات بعد التقديم

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع! احصل الان

عرض الإجابات بعد التقديم

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان