السؤال #1

Refer to the exhibit.An engineer is configuring a VMM domain integration, but the operation fails to complete. Which two actions resolve the issue? (Choose two.)

A. Configure the route from virtual machine manager OOB management network to vCenter

B. Use a different device package

C. Change VMware vCenter IP address

D. Change the VMware vCenter access credentials

E. Update the VMware vCenter version to be compatible with the Cisco ACI release

عرض الإجابة

اجابة صحيحة: CD

السؤال #2

Refer to the exhibit. The vPC between switch1 and switch2 does not work. Which two actions resolve the problem? (Choose two.)

A. Match the vPC domain ID between the two devices

B. Configure the IP address on the interface

C. Activate VLANs on the vP

D. Correct the configuration of the vPC peer link and the vPC peer keepalive

E. Configure one of the switches as primary for the vPC

عرض الإجابة

اجابة صحيحة: AC

السؤال #3

An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN. The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot. Which action resolves the issue?

A. Remove all of the local storage that is installed

B. Delete and reconfigure the pWWN of the SAN boot target

C. Remove all of the ISO images that are mounted as a virtual CD-ROM

D. Delete and reconfigure the boot LUN

E. Reveal Answer

عرض الإجابة

اجابة صحيحة: A

السؤال #4

Refer to the exhibit.The VXLAN fabric is deployed with this configuration:•The VLAN 50 interface has no IP address on VTEP1 and VTEP4•The VLAN 100 interface has no IP address on VTEP2 and VTEP3•The nve1 interface is configured on all VTEPsHost A experiences timeouts when attempting to ping host B. Which set of actions allows host A to reach host B?

A. On VTEP1, associate VNI 50000 to Test_Telco VRFOn VTEP4, associate VNI 50000 to Test_Telco VRF

B. On VTEP2, associate VNI 30000 to Test_Telco VRFOn VTEP4, associate VNI 20000 to Test_Telco VRF

C. On VTEP1, associate VNI 30000 to Test_Telco VRFOn VTEP4, associate VNI 20000 to Test Telco VRF

D. On VTEP2, associate VNI 55000 to Test_Telco VRFOn VTEP4, associate VNI 50000 to Test_Telco VRF

عرض الإجابة

اجابة صحيحة: A

السؤال #5

Refer to the exhibit.A Cisco VXLAN must use bidirectional PIM so that:•Spine2 is the active RP for multicast group 225.0.0.0/24.•Loopback 254 is used as a logical interface for PIM configuration.After configuration was applied, Spine1 became the active RP for multicast group 225.0.0.0/24 instead of Spine2. Which action resolves the issue?

A. Delete the bidir keyword from ip pim rp address command on Spine1

B. Configure the IP pim ssm range 232

C. Modify the subnet mask of Loopback 254 to /30 on Spine2

D. Change the IP address of Loopback 254 to 10

عرض الإجابة

اجابة صحيحة: D

السؤال #6

Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?

A. Configure a distributed anycast gateway on both peers

B. Configure iparp synchronize under the VPC domain on both peers

C. Configure peer-gateway under the VPC domain on both peers

D. Configure a different secondary IP address for one of the vPC peers

عرض الإجابة

اجابة صحيحة: B

السؤال #7

Refer to the exhibit. A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2.The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?

A. nable IPv6 routing on R1

B. onfigure an IPv6 BGP neighbor on R1

C. dvertise L2VPN EVPN under IPv4 unicast address family

D. reate a route map that sets the IPv6 next hop

عرض الإجابة

اجابة صحيحة: D

السؤال #8

Refer to the exhibit.An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails tomount. Which action resolves the issue?

A. tatically configure the target information in the Boot Policy

B. onfigure an MTU size of 9000 on the appliance port

C. onfigure a QoS policy on the vNIC

D. et a connection timeout value of 250 in the iSCSI Adapter Policy

عرض الإجابة

اجابة صحيحة: A

السؤال #9

Refer to the exhibit.An engineer must restore the connectivity issue between NEXUS-SW-3 and NEXUS-SW-4. The engineer can ping the physical and loopback interfaces used in the underlay from VTEP-1. However, communication between the SVIs in NEXUS-SW-3 and NEXUS-SW-4 fails. Which action resolves the issue?

A. Change the VNI to VLAN mapping on the NEXUS-SW-2

B. Reload the NEXUS-SW-2 to enable the hardware Ethernet store-and-fwd-switching feature

C. Manually set the interface MTU to support jumbo frames on the NEXUS-SW-2

D. Reconfigure the VXLAN features in the VTEP switches on the NEXUS-SW-2

عرض الإجابة

اجابة صحيحة: A

السؤال #10

An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?

A. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2

B. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2

C. shell=Security_Domain_1/Read_Role_1|Read_Role_2

D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

E. Reveal Answer

عرض الإجابة

اجابة صحيحة: D

السؤال #11

Refer to the exhibit.A Cisco VXLAN must use bidirectional PIM so that:•Spine2 is the active RP for multicast group 225.0.0.0/24.•Loopback 254 is used as a logical interface for PIM configuration.After configuration was applied, Spine1 became the active RP for multicast group 225.0.0.0/24 instead of Spine2. Which action resolves the issue?

A. Delete the bidir keyword from ip pim rp address command on Spine1

B. Configure the IP pim ssm range 232

C. Modify the subnet mask of Loopback 254 to /30 on Spine2

D. Change the IP address of Loopback 254 to 10

عرض الإجابة

اجابة صحيحة: D

السؤال #12

Refer to the exhibit.An engineer configures EVPN on Switch-1. but the neighbors fail to exchange EVPN routes. Which action resolves the issue?

A. Configure neighbor 192

B. Activate the IPv4 unicast address family for neighbor 192

C. Enable the send extended community option for the L2VPN EVPN address family

D. Advertise L2VPN EVPN under the IPv4 unicast address family

عرض الإجابة

اجابة صحيحة: C

السؤال #13

Refer to the exhibit. After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A?(Choose two.)

A. onfigure the local vPC role priority to have a lower value than Switch-A

B. onfigure the local vPC role priority to have a higher value than Switch-A

C. isable and then re-enable the vPC peer-keepalive link

D. onfigure the local vPC role priority to have the same value as Switch-A

E. isable and then re-enable the vPC peer link

عرض الإجابة

اجابة صحيحة: BE

السؤال #14

Refer to the exhibit.To avoid service disruption, an engineer must move the server from LEAF_1 to LEAF_2. After running the test, the engineer noticed that LEAF_2 failed to forward network traffic into the VXLAN fabric. The BGP, interface NVE, and VNI were confirmed to be configured as expected. Which two actions must be taken on LEAF_2 to resolve the issue? (Choose two.)

A. Add fabric forwarding mode anycast-gateway on interface Vlan100

B. Configure correspondent IP addressing on every interface

C. Change the fabric forwarding anycast-gateway-mac MAC address

D. Remove ip forward from interface Vlan30 and add it on interface Vlan100

E. Enable HMM tracking to advertise host routes into the VXLAN fabric

عرض الإجابة

اجابة صحيحة: CE

السؤال #15

Refer to the exhibit A Cisco VXLAN must use bidirectional PIM so that*Spine2 is the active RP for multicast group 225 0 0 0V24*Loopback 254 is used as a logical interface for PIM configurationAfter configuration was applied, Spine1 became the active RP for multicast group 225.0.0.0/24 instead of Spine2. Which action resolves the issue?

A. odify the subnet mask of Loopback 254 to ' 30 on Spine2

B. elete the bidir keyword from ip pim rp address command on Spine1

C. hange the IP address of Loopback 254 to 10 254 254 254 on Spine2

D. onfigure the IP pim ssm range 232

عرض الإجابة

اجابة صحيحة: A

السؤال #16

Refer to the exhibit. After a failover occurs, which two actions must be performed on Switch-B to manuallypreempt the operational primary role back to Switch-A? (Choose two.)

A. Configure the local vPC role priority to have a lower value than Switch-

B. Configure the local vPC role priority to have a higher value than Switch-A

C. Disable and then re-enable the vPC peer-keepalive link

D. Configure the local vPC role priority to have the same value as Switch-A

E. Disable and then re-enable the vPC peer link

عرض الإجابة

اجابة صحيحة: BE

السؤال #17

Refer to the exhibit. A network engineer connects the Cisco Nexus switch management port to the Internet using DHCP to allow the Guest shell that runs on the switch to download Python packages. The engineer can ping google.com from the Cisco Nexus switch, but the Guest shell fails to download Python packages. Which action resolves the problem?

A. Update the Python packages directly on the Cisco Nexus switch

B. Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP

C. Manually configure NTP in the Guest shell

D. Connect the Guest shell to data plane interfaces to be able to connect to the networks outside of the Cisco Nexus switch

عرض الإجابة

اجابة صحيحة: B

السؤال #18

A customer configures HSRP between two data centers that are interconnected with OTV. Theconfiguration succeeds, but traffic between two ESXi virtual hosts on the same site is routedsuboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

A. isable first-hop redundancy

B. ilter HSRP traffic by using a Layer 3 VACL on the OTV edge devices

C. ilter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch

D. ilter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch

E. ilter HSRP by using a Layer 2 MAC-list on the OTV edge devices

عرض الإجابة

اجابة صحيحة: AB

السؤال #19

A mission-critical server is connected to site

A. AConnectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging

B. AUse route-map to advertise this MAC statically and redistribute with ISIS

C. BUnknown unicast flooding is not allowed

D. CUse the otv flood mac <> command to selectively flood traffic for a given MAC

E. DUse the otv isis bfd <> command to configure BFD protocol

عرض الإجابة

اجابة صحيحة: C

السؤال #20

Refer to the exhibit. A PC belongs to VLAN 68. The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?

A. Replace HSRP with GLBP

B. Remove the HSRP configuration

C. Enable the peer-gateway feature

D. Configure iparp synchronization on both switches

عرض الإجابة

اجابة صحيحة: C

السؤال #21

Refer to the exhibit.A port channel on a Cisco Nexus 9000 Series Switch uplink experiences connectivity issues. Which configuration resolves the issue?

A. channel-group 100 mode passive

B. channel-group 100 force mode on

C. channel-group 100 mode on

D. channel-group 100 mode active

عرض الإجابة

اجابة صحيحة: D

السؤال #22

Refer to the exhibit.An engineer must restore the connectivity issue between NEXUS-SW-3 and NEXUS-SW-4. The engineer can ping the physical and loopback interfaces used in the underlay from VTEP-1. However, communication between the SVIs in NEXUS-SW-3 and NEXUS-SW-4 fails. Which action resolves the issue?

A. Change the VNI to VLAN mapping on the NEXUS-SW-2

B. Reload the NEXUS-SW-2 to enable the hardware Ethernet store-and-fwd-switching feature

C. Manually set the interface MTU to support jumbo frames on the NEXUS-SW-2

D. Reconfigure the VXLAN features in the VTEP switches on the NEXUS-SW-2

عرض الإجابة

اجابة صحيحة: A

السؤال #23

An engineer connected two Cisco UCS I/O modules to fabric interconnect with four links. When link 4 between the IOM-1 and primary fabric interconnect went down, the connectivity through IOM-1 from blade slots 3, 4, 7, and 8 failed over to IOM-2 and to the standby fabric interconnect.

A. Re-acknowledge the chassis

B. Reseat the chassis

C. Reseat IMO-1

D. Re-acknowledge IMO-1

عرض الإجابة

اجابة صحيحة: D

السؤال #24

Refer to the exhibit.An engineer monitors a Cisco UCS server logs and discovers a blade discovery issue. Which procedure resolves the issue?

A.

B.

C.

D.

عرض الإجابة

اجابة صحيحة: D

السؤال #25

Refer to the exhibit.An engineer must restore the connectivity issue between NEXUS-SW-3 and NEXUS-SW-4. The engineer can ping the physical and loopback interfaces used in the underlay from VTEP-1. However, communication between the SVIs in NEXUS-SW-3 and NEXUS-SW-4 fails. Which action resolves the issue?

A. Change the VNI to VLAN mapping on the NEXUS-SW-2

B. Reload the NEXUS-SW-2 to enable the hardware Ethernet store-and-fwd-switching feature

C. Manually set the interface MTU to support jumbo frames on the NEXUS-SW-2

D. Reconfigure the VXLAN features in the VTEP switches on the NEXUS-SW-2

عرض الإجابة

اجابة صحيحة: A

السؤال #26

Refer to the exhibit.A port channel on a Cisco Nexus 9000 Series Switch uplink experiences connectivity issues. Which configuration resolves the issue?

A. channel-group 100 mode passive

B. channel-group 100 force mode on

C. channel-group 100 mode on

D. channel-group 100 mode active

عرض الإجابة

اجابة صحيحة: D

السؤال #27

Refer to the exhibit.Two Cisco Nexus Series Switches have been configured to form OSPF neighborship. Which action resolves the issue?

A. Configure the same MTU values on adjacent interfaces

B. Configure the switch ID of the neighbor as 10

C. Configure the same authentication password on both switches

D. Configure ACL to allow multicast IP on the OSPF interface

عرض الإجابة

اجابة صحيحة: A

السؤال #28

A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

A. Disable first-hop redundancy

B. Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices

C. Filter HSRP by using a Layer 2 MAC list on the ESXivSwitch

D. Filter HSRP traffic by using a Layer 3 VACL on the ESXivSwitch

E. Filter HSRP by using a Layer 2 MAC list on the OTV edge devices

عرض الإجابة

اجابة صحيحة: AB

السؤال #29

An engineer removes a VMM domain from an endpoint group called EPG-1, but the distributed portgroup fails to be deleted. Which action must be taken to resolve the issue?

A. emove the port group manually

B. igrate all virtual machines in the EPG-1 to different hypervisors

C. emove the remaining EPGs from the VMM domain

D. igrate all virtual machines in the EPG-1 to different port groups

عرض الإجابة

اجابة صحيحة: D

السؤال #30

Refer to the exhibit.An engineer applied a VXLAN tunnel between Cisco Nexus 5000 Series Switches to extend the Layer 2 segment between N7K-1 and N7K-2. However, there is still no reachability between N7K-1 and N7K-2 over VLAN 200. Which configuration on N5K-2 resolves the issue?

A. bridge-domain 200member vni 9000

B. interface vlan 200vrf member vxlan-9000

C. interface nve 1member vni 9000 mcast-group 224

D. vlan 200vn-segment 9000

عرض الإجابة

اجابة صحيحة: D

السؤال #31

A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)

A. Configure the NVE interfaces to be Up on both switches

B. Set a different distributed gateway virtual MAC address

C. Set a different secondary IP addresses on NVE source-interface

D. Configure the same VNI to multicast group maping

E. Set a different primary IP addresses on NVE source-interface

عرض الإجابة

اجابة صحيحة: AD

السؤال #32

Refer to the exhibit.A port channel on a Cisco Nexus 9000 Series Switch uplink experiences connectivity issues. Which configuration resolves the issue?

A. channel-group 100 mode passive

B. channel-group 100 force mode on

C. channel-group 100 mode on

D. channel-group 100 mode active

عرض الإجابة

اجابة صحيحة: D

السؤال #33

Refer to the exhibit.During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

A. Reconfigure the Drive Type from 'Removable' to 'Non-Removable'

B. Insert an SD card into SLOT-2

C. Configure the RAID that is associated with the card

D. Set SLOT-1 Sync Mode to 'Auto'

عرض الإجابة

اجابة صحيحة: B

السؤال #34

An engineer is troubleshooting an unexpected blade-server reboot. One of the DIMMs is displayed inside Cisco UCS Manager as "degraded with correctable errors" but is still available for the OS to use. Which action resolves the issue?

A. Reset the Cisco UCS chassis

B. Replace the DIMM

C. Reset the BMC

D. Replace the CPU

عرض الإجابة

اجابة صحيحة: B

السؤال #35

Refer to the exhibit. An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used. Which action resolves the problem?

A. Configure each uplink to be a member of a separate LACP port channel

B. Configure the pinning max-link as 2

C. Configure destination-mac load balancing on N5K-Core-1

D. Configure source-destination load balancing on N5K-Core-1

عرض الإجابة

اجابة صحيحة: B

السؤال #36

Refer to the exhibit.An engineer must restore the connectivity issue between NEXUS-SW-3 and NEXUS-SW-4. The engineer can ping the physical and loopback interfaces used in the underlay from VTEP-1. However, communication between the SVIs in NEXUS-SW-3 and NEXUS-SW-4 fails. Which action resolves the issue?

A. Change the VNI to VLAN mapping on the NEXUS-SW-2

B. Reload the NEXUS-SW-2 to enable the hardware Ethernet store-and-fwd-switching feature

C. Manually set the interface MTU to support jumbo frames on the NEXUS-SW-2

D. Reconfigure the VXLAN features in the VTEP switches on the NEXUS-SW-2

عرض الإجابة

اجابة صحيحة: A

السؤال #37

Refer to the exhibit.A network engineer notices a sudden interruption to the HSRP adjacency between the switches. The packet loss is reported on the servers for which the default gateway is set as the virtual IP of the HSRP. All servers on the VLAN can exchange ping messages. Which configuration set must be applied on the HSRP peers to resolve the adjacency issue?

A. key 0accept-lifetime 00:00:00 Oct 01 2018 23:59:59 Sep 01 2020

B. key 0send-lifetime 00:00:00 Oct 01 2018 23:59:59 Sep 01 2020

C. key 1send-lifetime 00:00:00 Jun 01 2018 23:59:59 Sep 01 2022

D. key 1accept-lifetime 00:00:00 Jun 01 2018 23:59:59 Sep 01 2020

عرض الإجابة

اجابة صحيحة: D

السؤال #38

Refer to the exhibit.Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?

A. Configure a distributed anycast gateway on both peers

B. Configure ip arp synchronize under the VPC domain on both peers

C. Configure peer-gateway under the VPC domain on both peers

D. Configure a different secondary IP address for one of the vPC peers

عرض الإجابة

اجابة صحيحة: C

السؤال #39

Refer to the exhibit.A port channel on a Cisco Nexus 9000 Series Switch uplink experiences connectivity issues. Which configuration resolves the issue?

A. channel-group 100 mode passive

B. channel-group 100 force mode on

C. channel-group 100 mode on

D. channel-group 100 mode active

عرض الإجابة

اجابة صحيحة: D

السؤال #40

Refer to the exhibit. An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

A. Change the local group number to 255 or less and request that the remote data center matches the group number in its configuration

B. Set the local group number as 300 in the remote data center configuration

C. Run version 1 and version 2 HSRP on VLAN300 in the local data center

D. Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1

عرض الإجابة

اجابة صحيحة: A

السؤال #41

Refer to the exhibit.An OSPF adjacency between Router - A and Router - B cannot reach the FULL state. Which action resolves the issue?

A. Adjust the MTU on Router - A to 1600

B. Disable the check of the MTU value

C. Set the OSPF media type to point - to - point

D. Adjust the MTU on Router - B to 1604

عرض الإجابة

اجابة صحيحة: B

السؤال #42

Refer to the exhibit.The VXLAN fabric with BGP EVPN control plane experiences connectivity issues. The hosts in the initial deployed VLAN fail to communicate. The environment is configured as follows:Private BGP ASN 65122 is used across the whole fabric.Each leaf node has iBGP peers with each spine node with default values.Address family L2VPN EVPN is enabled on all leaf and spine BGP speakers.Which BGP feature is required on the spines for all EVPN routes to be advertised throughout the VXLAN fabric?

A. ebgp-multihop

B. allowas-in

C. route-reflector-client

D. remove-private-as

عرض الإجابة

اجابة صحيحة: C

السؤال #43

Refer to the exhibit.After a failover occurs, which two actions must be performed on Switch - B to manually preempt the operational primary role back to Switch - A? (Choose two.)

A. Configure the local vPC role priority to have a lower value than Switch - A

B. Configure the local vPC role priority to have a higher value than Switch - A

C. Disable and then re - enable the vPC peer - keepalive link

D. Configure the local vPC role priority to have the same value as Switch - A

E. Disable and then re - enable the vPC peer link

عرض الإجابة

اجابة صحيحة: BE

السؤال #44

Refer to the exhibit. An OSPF adjacency between Router-A and Router-B fails to reach the FULL state. Which action resolves the issue?

A. djust the MTU on Router-A to 1600

B. isable the check of the MTU value

C. et the OSPF media type to point-to-point

D. djust the MTU on Router-B to 1604

عرض الإجابة

اجابة صحيحة: B

السؤال #45

Refer to the exhibit. After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A?(Choose two.)

A. Configure the local vPC role priority to have a lower value than Switch-A

B. Configure the local vPC role priority to have a higher value than Switch-A

C. Disable and then re-enable the vPC peer-keepalive link

D. Configure the local vPC role priority to have the same value as Switch-A

E. Disable and then re-enable the vPC peer link

عرض الإجابة

اجابة صحيحة: BE

السؤال #46

An engineer troubleshoots a fabric discovery failure. Which two requirements about switch connectivity must be verified to solve the problem? (Choose two.)

A. A Cisco APIC must be attached to a spine node only

B. A Cisco APIC must be attached to leaf nodes

C. Spine nodes must connect to other spine nodes

D. A Cisco APIC must be dual-attached to two separate spine nodes

E. Leaf nodes must connect to spine nodes only

عرض الإجابة

اجابة صحيحة: BE

السؤال #47

An upgrade of protected RPMs from the Bash shell did not take effect. Which action is required for the changes to take effect?

A. Restart the Bash shell

B. Reload the switch

C. Upgrade the RPMs from the Guest shell

D. Disable and reenable the Bash feature

عرض الإجابة

اجابة صحيحة: B

السؤال #48

Refer to the exhibit.A web browser displays a “not secure” warning message when accessing the web interface of CiscoUCS Manager. Which action resolves the issue?

A. oad third-party certificate to UCS Manager

B. se the correct TCP port for HTTPS

C. se a supported web browser

D. se a supported version of UCS Manager

عرض الإجابة

اجابة صحيحة: A

السؤال #49

An engineer removes a VMM domain from an endpoint group called ‘EPG-1â€ , but the distributed port group fails to be deleted. Which action resolves the issue?

A. Manually remove the port group

B. Migrate all virtual machines in the EPG-1 to different hypervisors

C. Remove the remaining EPGs from the VMM domain

D. Migrate all virtual machines in the EPG-1 to different port groups

عرض الإجابة

اجابة صحيحة: C

السؤال #50

Refer to the exhibit. The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

A. Enable IP redirects

B. Set the MTU to 1500 bytes

C. Configure HSRP version 2

D. Configure the same HSRP group on both devices

عرض الإجابة

اجابة صحيحة: A

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان

View The Updated 300-615 Exam Questions

عرض الإجابات بعد التقديم

لا تريد أن تفوت شيئا؟

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع! احصل الان

View The Updated 300-615 Exam Questions

عرض الإجابات بعد التقديم

اجتياز اختبار الممارسة Cisco وPMP وCISA وCISM وAWS بنسبة 100% للبيع!
احصل الان