لا تريد أن تفوت شيئا؟

نصائح اجتياز امتحان الشهادة

آخر أخبار الامتحانات ومعلومات الخصم

برعاية وحديثة من قبل خبرائنا

نعم، أرسل لي النشرة الإخبارية

خذ اختبارات أخرى عبر الإنترنت

السؤال #1
Campus users report a poor wireless experience. An engineer investigating the issue notices that in high-density areas, the wireless clients fail to switch the AP to which are automatically connected. This sticky client behavior is causing roaming issues. Which feature must the engineer configure?
A. Load balancing and band select
B. optimized roaming
C. Layer 3 roaming
D. Layer 2 roaming
عرض الإجابة
اجابة صحيحة: B

View The Updated 300-425 Exam Questions

SPOTO Provides 100% Real 300-425 Exam Questions for You to Pass Your 300-425 Exam!

السؤال #2
Refer to the exhibit. An enterprise has offices spread around the globe. The APs are connected to different controllers installed in separate datacenters. The IT team wants to allow clients to roam from controllers in group ABC to controllers in group XYZ. Which feature must be incorporated in the design to accomplish this task?
A. Aswitch peer group
B. Bworkgroup bridge
C. CmDNS gateway
D. Dmobility lists
عرض الإجابة
اجابة صحيحة: D
السؤال #3
An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used toensure a consistent experience for all of the wireless clients?
A. the client that has the highest RF properties
B. the client that is used most by the company
C. the client that is used least by the company
D. the client with the worst RF characteristics
عرض الإجابة
اجابة صحيحة: D
السؤال #4
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)
A. The coverage area must have a noise floor that does not exceed −87 dBm
B. The client device must have at least an −67 dBm RSSI
C. The rate of retransmitted packets must be 15 percent or below
D. The rate of retransmitted packets must be 20 percent or below
E. The client device must have at least an −65 dBm RSSI
عرض الإجابة
اجابة صحيحة: BC
السؤال #5
A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectrum?
A. and Select
B. RM
C. isco Centralized Key Management
D. oad balancing
عرض الإجابة
اجابة صحيحة: A
السؤال #6
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
A. se a battery pack to power APs
B. se a drawing of the office space to draw AP and client placements
C. se DoS attack on APs while measuring the throughput
D. se APs with directional antennas
E. se APs with external antennas
F. se APs with built-in antennas
عرض الإجابة
اجابة صحيحة: ABF
السؤال #7
An engineer is implementing a wireless design for a service provider. The design includes a Catalyst 9800, a stack of two Catalyst 9300X-48HX switches, and 9166 APs. Each AP must be named using the Floor-439412509-01X sting where X is the area number. The engineer wants to connect the APs to the switch stack using POE. How many APs must the engineer connect to the stack so the APs run using full functionalities?
A. ll ports on switch 1 of the stack
B. alf ports per switch
C. ll ports of the switches
D. ll ports on switch 2 of the stack
عرض الإجابة
اجابة صحيحة: C
السؤال #8
A wireless engineer is utilizing the voice readiness tool in Cisco Prime for a customer that wants to deploy Cisco IP phones. Which dBm range is the network inspected against?
A. −78 to −65 dBm
B. −72 to −67 dBm
C. −85 to −65 dBm
D. −85 to −67 dBm
عرض الإجابة
اجابة صحيحة: D
السؤال #9
A company wants to replace its existing PBX system with a new VoIP System that will include wireless IP phones. The CIO has concerns about whether the company's existing wireless network can support the new system. Which tool in Cisco Prime can help ensure that the current network will support the new phone system?
A. ocation Readiness
B. ite Calibration
C. ap Editor
D. oice Readiness
عرض الإجابة
اجابة صحيحة: D
السؤال #10
Refer to the exhibit. What is the main reason why the Wi-Fi design engineer took a different approach than installing the APs in the offices, even though that installation provides better coverage?
A. esthetics
B. ransmit power considerations
C. ntenna gain
D. ower supply considerations
عرض الإجابة
اجابة صحيحة: A
السؤال #11
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
A. The edge of the cell should be −67 dBm
B. The edge of the cell should be below 35 RSSI
C. The measurement should be done on the 2
D. One AP should be deployed per 3000 square feet
عرض الإجابة
اجابة صحيحة: A
السؤال #12
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choosethree.)
A. Use a battery pack to power APs
B. Use a drawing of the office space to draw AP and client placements
C. Use DoS attack on APs while measuring the throughput
D. Use APs with directional antennas
E. Use APs with external antennas
F. Use APs with built-in antennas
عرض الإجابة
اجابة صحيحة: ABF
السؤال #13
A community bank has three campus locations and one HQ with the data center operations. Each campus location has four Cisco Catalyst 9120 APs. The data center has a Catalyst 9800 WLC with eight Catalyst 9120 APs. Poor WAN uplinks cause impacted branch AP and wireless client connectivity back to HQ, and each campus location is now planned to have its own EWC controller based on C9120 AP to keep traffic local. This new design must accommodate these requirements:- Guest WLAN will be routed locally.- Employee WLAN must be authenticated 802.1x PEAP via HQ data centerISE but can pass traffic locally once authenticated.- HQ WLC will be the primary backup WLC for each WLC.Which design approach should the consulting engineer take?
A. wo C9120 campus APs must be converted to EWC mode, one for the active controller and the other for standby with HQ WLC set as N+1 backup
B. wo C9120 campus APs must be converted to EWC mode, one for the active controller and the other for standby set as N+1 backup
C. ne C9120 AP in each campus must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC set as N+1 backup
D. ne C9120 campus AP must be converted to EWC mode, and the preferred controller is set to that AP with HQ WLC should be paired as mobility peer and configured as N+1 backup
عرض الإجابة
اجابة صحيحة: C
السؤال #14
What causes the most signal attenuation, based on the wireless design tools?
A. cinder block wall
B. metal door
C. glass wall
D. office window
عرض الإجابة
اجابة صحيحة: B
السؤال #15
What causes the most signal attenuation, based on the wireless design tools?
A. cinder block wall
B. metal door
C. glass wall
D. office window
عرض الإجابة
اجابة صحيحة: B
السؤال #16
A wireless engineer is utilizing the voice readiness tool in Cisco Prime for a customer that wants to deploy Cisco IP phones. Which dBm range is the network inspected against?
A. −78 to −65 dBm
B. −72 to −67 dBm
C. −85 to −65 dBm
D. −85 to −67 dBm
عرض الإجابة
اجابة صحيحة: D
السؤال #17
What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?
A. 0%
B. 0%
C. 0%
D. 0%
عرض الإجابة
اجابة صحيحة: C
السؤال #18
A customer is concerned about mesh backhaul link security. Which level of encryption does the backhaul link use?
A. ash
B. ES
C. EP
D. DES
عرض الإجابة
اجابة صحيحة: B
السؤال #19
An engineer must speed up the reauthentication delays that are being experienced on the wireless infrastructure by deploying a key-caching mechanism. Which mechanism must be configured?
A. EAP
B. T
C. MF
D. TK-randomization
عرض الإجابة
اجابة صحيحة: B
السؤال #20
As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which two areas is the engineer most likely to findsources of 2.4 GHz and 5 GHz RF noise? (Choose two.)
A. magnetic resonance imaging
B. kitchen
C. Gamma Knife radiation treatment
D. X-ray radiography
E. patient room
عرض الإجابة
اجابة صحيحة: BE
السؤال #21
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)
A. PoE battery
B. spirit level
C. access point
D. tall tripod
E. goggles
F. ladder
G. Reveal Answer
عرض الإجابة
اجابة صحيحة: ACD
السؤال #22
A wireless engineer is calibrating a floor using Cisco Prime Infrastructure. Which setting in the WLC must be disabled before the floor calibration is started?
A. overage Hole Detection
B. x Power Control
C. leanAir
D. ynamic Channel Assignment
عرض الإجابة
اجابة صحيحة: B
السؤال #23
An engineer has performed a predictive site survey for high-speed data and voice in an indoor office. What is the recommended data rate with -67 dBm signal level for optimal VoWLAN design?
A. Mbps on 802
B. 2 Mbps on 802
C. 4 Mbps on 802
D. 4 Mbps on 802
عرض الإجابة
اجابة صحيحة: C
السؤال #24
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
A. The edge of the cell should be −67 dBm
B. The edge of the cell should be below 35 RSSI
C. The measurement should be done on the 2
D. One AP should be deployed per 3000 square feet
عرض الإجابة
اجابة صحيحة: A
السؤال #25
An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used to ensure a consistent experience for all of the wireless clients?
A. he client that has the highest RF properties
B. he client that is used most by the company
C. he client that is used least by the company
D. he client with the worst RF characteristics
عرض الإجابة
اجابة صحيحة: D
السؤال #26
Why is 802.11a connectivity reduced in an X-ray room?
A. X-rays create significant non-Wi-Fi interference on the 802
B. X-rays impact the 802,11a UNll-2 channels that cause access points to dynamically change channels
C. X-rays within these rooms cause multipath issues
D. X-ray rooms exhibit increased signal attenuation
عرض الإجابة
اجابة صحيحة: D
السؤال #27
An engineer has performed a predictive site survey for high-speed data and voice in an indoor office. What is the recommended data rate with גˆ’67 dBm signallevel for optimal VoWLAN design?
A. 6 Mbps on 802
B. 24 Mbps on 802
C. 12 Mbps on 802
D. 24 Mbps on 802
عرض الإجابة
اجابة صحيحة: C
السؤال #28
A rapidly expanding company has tasked their network engineer with wirelessly connecting a newcubicle area with Cisco workgroup bridges until the wired network is complete. Each of 42 new usershas a computer and VoIP phone. How many APs for workgroup bridging must be ordered to keepcost at a minimum while connecting all devices?
A.
B.
C.
D.
عرض الإجابة
اجابة صحيحة: C
السؤال #29
A wireless engineer is using Ekahau Site Survey to validate that an existing wireless network is operating as expected. Which type of survey should be used to identify the end-to-end network performance?
A. GPS assisted
B. spectrum analysis
C. passive
D. active ping
عرض الإجابة
اجابة صحيحة: B
السؤال #30
A technician connects a Cisco Aironet 3700 Series AP to a switch and realizes that the AP is coming up with 3x3 MIMO. What explains this behavior?
A. redundant power supply is unavailable on the switch
B. he switch is 802
C. he AP is getting power from a power injector
D. he switch is PoE+ capable
عرض الإجابة
اجابة صحيحة: B
السؤال #31
Where must the APs be mounted when used in a high-density wireless network to provide 6 dB to 20 dB of attenuation to a cell?
A. n the aisle
B. nder the seat
C. bove the stage
D. nder the stage
عرض الإجابة
اجابة صحيحة: B
السؤال #32
An enterprise is using a Cisco AireOS controller and Wi-Fi 6 APs. The controller is installed in the head office, and the employees primarily use Apple OS devices. The APs broadcast WLAN ENT-WLAN406558520-1 for the employees and a guest WLAN with similar naming. What needs to be enabled on the controller to optimize roaming?
A. Aggregated Probe Response Optimization
B. Fast SSID Changing
C. Load Balancing Window
D. Client Timers
E. Reveal Answer
عرض الإجابة
اجابة صحيحة: B
السؤال #33
Refer to the exhibit A wireless consultant is performing an onsite survey using AirMagnet Survey PRO. What must be configured on the floor map so that the results appear properly?
A. alibrate the dimensions
B. how details of the user density
C. dd inter-floor bleed
D. isplay details of the desk numbers
عرض الإجابة
اجابة صحيحة: A
السؤال #34
What causes the most signal attenuation, based on the wireless design tools?
A. cinder block wall
B. metal door
C. glass wall
D. office window
عرض الإجابة
اجابة صحيحة: B
السؤال #35
A wireless engineer is using Ekahau Site Survey to validate that an existing wireless network is operating as expected. Which type of survey should be used to identify the end-to-end network performance?
A. GPS assisted
B. spectrum analysis
C. passive
D. active ping
عرض الإجابة
اجابة صحيحة: B
السؤال #36
An engineer must create a multicampus architecture wireless design to accommodate 4500 access points for wireless data Which model controller the requirements to support all access points on one high availability controller setup?
A. 3504
B. 5508
C. 5520
D. 8540
E. Reveal Answer
عرض الإجابة
اجابة صحيحة: D
السؤال #37
An engineer has deployed a group of APs in an auditorium and notices that the APs are showing high co-channel interference. Which profile is used to adjust the parameters for these high-density APs?
A. oS profile
B. VC profile
C. F profile
D. SE profile
عرض الإجابة
اجابة صحيحة: C
السؤال #38
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. What is the minimumrequirement for the design?
A. overlapping גˆ’72 dBm coverage from two access points
B. continuous גˆ’67 dBm coverage from one access point
C. continuous גˆ’72 dBm coverage from one access point
D. overlapping גˆ’67 dBm coverage from two access points
عرض الإجابة
اجابة صحيحة: D
السؤال #39
A customer has determined that aesthetics is a primary concern for their upcoming guest deployment. Which design consideration can be leveraged to address this concern?
A. aint the access point to cover the LED from being noticeable
B. se enclosures to hide the wireless infrastructure in the surrounding environment
C. se AIR-AP-BRACKET-1 to allow for greater mounting locations
D. eploy environmentally friendly cabling components to blend into the environment
عرض الإجابة
اجابة صحيحة: B
السؤال #40
An engineer Is trying to determine the most cost-effective way to deploy high availability for a campus enterprise wireless network that currently leverages three wireless LAN controllers. Which architecture should the engineer deploy?
A. N+1 solution without SS0
B. N+1 with SSO
C. N+N solution without SSO
D. N+N with SSO
عرض الإجابة
اجابة صحيحة: B
السؤال #41
What causes the most signal attenuation, based on the wireless design tools?
A. cinder block wall
B. metal door
C. glass wall
D. office window
عرض الإجابة
اجابة صحيحة: B
السؤال #42
An engineer is designing a wireless network that will support many different types of wireless clients.When conducting the survey, which client must be used to ensure a consistent experience for all ofthe wireless clients?
A. he client that has the highest RF properties
B. he client that is used most by the company
C. he client that is used least by the company
D. he client with the worst RF characteristics
عرض الإجابة
اجابة صحيحة: D
السؤال #43
An engineer must perform a predictive design for a wireless network for location readiness and to mitigate interference. Which power level does the engineer use?
A. 10 mw
B. 18 mw
C. 20 mw
D. 50 mw
E. Reveal Answer
عرض الإجابة
اجابة صحيحة: B
السؤال #44
Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?
A. UDP 16666 for control plane, EoIP (IP protocol 97) for data plane
B. UDP 16668 for control plane, UDP 16667 for data plane
C. UDP 16667 for control plane, UDP 16666 for data plane
D. UDP 16666 for control plane, UDP 16667 for data plane
عرض الإجابة
اجابة صحيحة: A
السؤال #45
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
A. The edge of the cell should be −67 dBm
B. The edge of the cell should be below 35 RSSI
C. The measurement should be done on the 2
D. One AP should be deployed per 3000 square feet
عرض الإجابة
اجابة صحيحة: A
السؤال #46
A warehouse has metal shelving that reflects RF signals. Which antenna strategy is best?
A. ACeiling-mounted omni-directional antennas only
B. BLow-gain directional antennas mounted on the aisles
C. CAPs installed randomly throughout the warehouse
D. DHigh-gain Yagi antennas pointing across shelves
عرض الإجابة
اجابة صحيحة: B
السؤال #47
Refer to the exhibit.A client roams between two APs that are registered to two different controllers, whereeach controller has an interface in the client subnet. Both controllers are running AireOS. Whichscenario explains the client roaming behavior?
A. ontrollers exchange mobility control messages (over UDP port 16666) and the client database entry is moved from the original controller to the new controller
B. ontrollers do not exchange mobility control messages (over UDP port 16666) andthe client database, entry is not moved from the original controller to the newcontroller
C. ontrollers exchange mobility control messages (over UDP port 16666) and a new client session is started with the new controller
D. ontrollers exchange mobility control messages (over UDP port 16666) and the client database entry is tunneled from the original controller to the new controller
عرض الإجابة
اجابة صحيحة: A
السؤال #48
Which two criteria must be considered when conducting an outdoor bridge site survey? (Choose two.)
A. near-far effect
B. weather
C. traffic lights
D. power lines
E. Fresnel zone
عرض الإجابة
اجابة صحيحة: BE
السؤال #49
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)
A. The coverage area must have a noise floor that does not exceed −87 dBm
B. The client device must have at least an −67 dBm RSSI
C. The rate of retransmitted packets must be 15 percent or below
D. The rate of retransmitted packets must be 20 percent or below
E. The client device must have at least an −65 dBm RSSI
عرض الإجابة
اجابة صحيحة: BC
السؤال #50
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)
A. PoE battery
B. spirit level
C. access point
D. tall tripod
E. goggles
F. ladder
عرض الإجابة
اجابة صحيحة: ACD
السؤال #51
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
A. The edge of the cell should be −67 dBm
B. The edge of the cell should be below 35 RSSI
C. The measurement should be done on the 2
D. One AP should be deployed per 3000 square feet
عرض الإجابة
اجابة صحيحة: A
السؤال #52
An engineer is designing a wireless network that will support many different types of wireless clients. When conducting the survey, which client must be used to ensure a consistent experience for all of the wireless clients?
A. the client that has the highest RF properties
B. the client that is used most by the company
C. the client that is used least by the company
D. the client with the worst RF characteristics
عرض الإجابة
اجابة صحيحة: B
السؤال #53
A wireless engineer is using Ekahau Site Survey to validate that an existing wireless network is operating as expected. Which type of survey should be used to identify the end-to-end network performance?
A. GPS assisted
B. spectrum analysis
C. passive
D. active ping
عرض الإجابة
اجابة صحيحة: B
السؤال #54
Which non-Wi-Fi interferer can be identified by Metageek Chanalyzer?
A. PDAs
B. jammers
C. smartphones
D. printers
عرض الإجابة
اجابة صحيحة: B

عرض الإجابات بعد التقديم

يرجى إرسال البريد الإلكتروني الخاص بك والواتس اب للحصول على إجابات الأسئلة.

ملحوظة: يرجى التأكد من صلاحية معرف البريد الإلكتروني وWhatsApp حتى تتمكن من الحصول على نتائج الاختبار الصحيحة.

بريد إلكتروني:
رقم الواتس اب/الهاتف:
Contact Us