Users in AS 65010 are connected with the application server in AS 65050 with these requirements: AS 65010 users are experiencing latency and congestion to connect with application server 172.16.50.10. AS 65030 must be restricted to become Transient Autonomous System for traffic flow. Links connected to AS 65020 and AS 65040 are underutilized and must be used efficiently for traffic. Which two configurations must be implemented to meet these requirements? (Choose two.)

Which two IS-IS parameters must match before two Level 2 peers can form an adjacency? (Choose two)

Which show command shows statistics for the control plane policy and is used to troubleshoot?

Refer to the exhibit: A network operator working for service provider with an employee id 3715 15:021 applied this configuration to a router. Which additional step should the engineer use to enable LDP?

A network engineer is configuring a router to send multicast traffic for the 239.10.10.10 group. Which configuration must an .... forward the traffic?

A network engineer is implementing BFD configuration changes on a customer's equipment. How is the bfd interval configuration on the interface disconnected?

An engineer is configuring multitopology IS-IS for IPv6 on router R1. Which additional configuration must be applied to the router to complete the task?

While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command. After you issue this command, which BGP packets does the PE accept?

A customer has requested that the service provider use a Cisco MPLS TE tunnel to force the E-line service to take a specific route What is used to send the traffic over the tunnel?

An engineer started to configure a router for OSPF. Which configuration must the engineer perform on the router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?

Which configuration enables BGP FlowSpec client function and installation of policies on all local interfaces?

What is the function of Cisco NFV infrastructure platform?

Refer to the exhibit: A network engineer is implementing an OSPF configuration Based on the output, which statement is true?

A network team has failed to implement IS-IS multitopology. What is the reason for it?

Drag and drop the BGP Best Path Algorithm rules from the left into the corresponding order of importance on the right.

An engineer working for a private telecommunication company with an employee id: 3414:81:713 is implementing this network, in which: Routers R1A and R1B are eBGP neighbors. iBGP is configured within AS 65515 and AS 65516. Network 192.168.2.0/24 is shared with AS 65516. Router R3A has an iBGP relationship with router R2A only. Router R2A has an iBGP relationship with routers R1A and R3A. Which additional task must the engineer perform to complete the configuration?

FRR is configured on a network. What occurs when the headend router on the path is alerted to a link failure over IGP?

Refer to the exhibit: After implementing a new design for the network, a technician reviews the pictured CLI output as part of the MOP. Which two statements describe what the technician can ascertain from the ImpNull output? (Choose two.)

Which task completes the configuration?

An engineer is implementing IGMP with SSM on a multicampus network that supports video streaming. Which task must the engineer perform as part of the process?

A network engineer with an employee id: 3812:12:993 has started to configure router R1 for IS-IS as shown. Which additional configuration must be applied to configure the IS-IS instance to advertise only network prefixes associated to passive interfaces?

How does Cisco MPLS TE use OSPF extensions to allow for optimized transit between a headend router and a destination router?

A network engineer is configuring RIP as the routing protocol between multiple PEs and CEs. The engineer must avoid advertising the same routes back to their sources. Which action should be performed on the routers to accomplish this task?

The service provider is serving hosts with two different multicast streams from source X and source Y. Source X is multicast group 224.0.0.0/8, and source Y is multicast group 226.0.0.0/8. Multicast source X should send its stream through bidirectional RP address 10.20.1.1, and multicast source Y should send its stream through RP address 10.20.2.1. Which configuration meets these requirements?