A non-802.11 device is suspected of causing interference on the WLAN. You are not certain of the location or type of device. What is the best solution for locating this non-802.11 device?

You administer a WLAN that offers a guest SSID of GUESTNWORK. User connect to the GUESTNWORK SSID, but report that they cannot browse the internet. The devices simply report no internet connection. What common problem causes this scenario?

You were previously onsite at XYZ’s facility to conduct a pre-deployment RF site survey. The WLAN has been deployed according to your recommendations and you are onsite again to perform a post-deployment validation survey. When performing this type of post-deployment RF site survey voice over Wi-Fi, what is an action that must be performed?

You are troubleshooting a client issue on a Windows laptop. The laptop can see and connect to 2.4 GHz APs, but is does not even see 5 GHz APs. While evaluating the issue, you determine that this problem is happening for all of the laptops of this model in the organization. Several other tablets connect on channel 48 and channel 52 in the same work areas. What is the likely problem?

You are troubleshooting a client problem with a 2.4 GHz WLAN connection. The client is experiencing surprisingly low data rates during the work day. You analyze the workspace outside of business hours and detect a strong signal with a typical noise floor at the client location. During working hours, the user works with a laptop in the area and uses an external USB hard drive for continuous data access. The user also states that the laptop works as expected on her home network. The user working approximately

In addition to coverage analysis results, what should be included in a post-deployment site survey report to ensure WLAN users experience acceptable performance?

What can an impedance mismatch in the RF cables and connectors cause?

You have received a report of poor wireless connections on the third floor of a building under your administration. Three individuals have reported the problem. Apparently, the connections are reporting a strong signal, but the users cannot access the Internet. With the problem identified, what is the next logical step in the troubleshooting process?

You are troubleshooting a problem with interference from a non-802.11 device. Given that the device is not a WLAN device, you cannot use a protocol analyzer and have chosen to use a spectrum analyzer. You want to view the signal from the interfering device over time to see the activity that is generating. What common spectrum analyzer view should you use for this analysis?

What fact is true regarding controllers and Aps in a split-MAC architecture?

A client complains of low data rates on his computer. When you evaluate the situation, you see that the signal strength is -84 dBm and the noise floor is -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. What is the likely cause of the low data rate issue?

What security method is commonly used for VoIP handsets when the infrastructure does not support OKC or FT roaming?

You are using a site survey tool for post-implementation validation. You have installed the appropriate adapter driver and imported a floor plan. Now, you want to take the next step in proper tool use. What must you do before gathering survey data after the floor plan is imported?

You are performing a post-implementation validation survey. What basic tool can be used to easily locate areas of high co-channel interference?

Option 43 must be configured to allow access points to locate controllers. In what network service should this option be configured?

The IEEE 802.11-2016 standard requires VHT capable devices to be backward compatible with devices using which other 802.11 physical layer specification (PHY)?

You are installing an AP to be used by 23 laptops. All laptops will connect on the 5 GHz frequency band. A neighbor network uses channels 1 and 6. What channel should be used for this AP and why?

You are using a site survey tool for post-implementation validation. You have installed the appropriate adapter driver and imported a floor plan. Now, you want to take the next step in proper tool use. What must you do before gathering survey data after the floor plan is imported?

A standard PoE injector is use to power an access point requiring 802.3at. CAT6 cabling is in use. What is the maximum distance supported between the access point and the Ethernet switch with the use of a midspan power injector?

You are planning for PoE in a standard office deployment. Which one of these devices is least likely to be a PoE PD?