Whether you are submitting a service request to Cisco Technical Assistance Center (TAC), processing an RMA, auditing inventory, or renewing support contracts, locating your switch’s serial number is an essential task. Cisco switches use an 11-character alphanumeric identifier—typically beginning with a three-letter manufacturing location code such as FOC, FCW, CAT, JMX, or SAL—that uniquely tracks the chassis across manufacturing, deployment, and support lifecycles.
Depending on whether the hardware is unboxed on a bench, operating in a production rack, bonded into a switch stack, or monitored across an enterprise network, you can retrieve the serial number using physical inspection, remote command-line interfaces (CLI), or network management protocols.
Table of Contents
Locating the Physical Serial Number on Switch Hardware
When a switch is unpowered, unconfigured, or offline, you can locate the serial number directly on the physical chassis without booting the operating system.
Step 1: Check for the Pull-Out Luggage Tag
Most modern fixed-configuration enterprise switches—including Cisco Catalyst 3650, 3850, 9200, 9300, and 9500 series—feature a slide-out plastic tab (frequently referred to as a luggage tag or RFID tab) on the front panel:
1. Locate the thin tab situated on the front panel, usually positioned above the primary port block or next to the console and management ports.
2. Gently pull the tab outward.
3. Read the printed label, which lists the switch serial number (SN), Product ID (PID), Version ID (VID), and an integrated RFID chip or 2D data matrix barcode.
Step 2: Inspect the Rear and Bottom Chassis Stickers
On older Catalyst switches (such as the Catalyst 2960, 3560, and 3750 series) and compact switches (Catalyst 1000 and 3560-CX):
1. Navigate to the rear of the unit.
2. Locate the metallic compliance label affixed near the AC power input receptacle or cooling fan modules.
3. Look for the field marked SN, Serial No, or directly below the primary chassis barcode. On compact fanless models, this sticker may be located on the bottom metal casing.
Step 3: Inspect Modular Supervisor and Line Card Faceplates
On modular chassis platforms (such as the Catalyst 4500, 6500, 9400, and 9600 series):
1. Note that the physical chassis and individual modules have separate serial numbers.
2. Find the chassis serial label on the top frame or inside the front frame trim near the power supply bays.
3. Locate module-specific serial numbers on the metal faceplate of each supervisor engine, line card, and power supply unit.
Finding Serial Numbers via Cisco IOS and IOS-XE CLI
When you have remote console, SSH, or Telnet access to an active switch running Cisco IOS or Cisco IOS-XE, the CLI provides complete hardware information without requiring physical inspection of the rack.
Step 1: Run the show inventory Command
The show inventory command is the standard and most reliable method to retrieve serial numbers for the chassis, internal subcomponents, and attached accessories.
Switch# show inventory
NAME: "c9300 24 Port PoE", DESCR: "Cisco Catalyst 9300 Series Switch"
PID: C9300-24P , VID: V01 , SN: FOC2345A1BC
NAME: "Power Supply Module 0", DESCR: "715W AC Power Supply"
PID: PWR-C1-715WAC , VID: V01 , SN: LIT22340XYZ
NAME: "TenGigabitEthernet0/1/1", DESCR: "10Gbase-SR SFP+"
PID: SFP-10G-SR , VID: V01 , SN: ONS18420123
In this output:
– PID: Represents the base hardware model (Product ID).
– VID: Denotes the hardware version revision (Version ID).
– SN: Contains the 11-character chassis or module serial number.
Step 2: Run the show version Command
For a quick chassis-level query, show version prints basic software and hardware parameters:
Switch# show version
...
cisco C9300-24P (X86) processor with 1813478K/3071KB of memory.
Processor board ID FOC2345A1BC
...
System serial number : FOC2345A1BC
Note: On fixed Catalyst switches, the Processor board ID matches the system serial number. However, on modular chassis (such as Catalyst 6500 or 9400), show version outputs the processor board ID of the active supervisor engine rather than the physical chassis itself. For modular hardware, always rely on show inventory.
Step 3: Filter CLI Outputs for Fast Scripting
To isolate the serial number string directly, pipe the CLI output through regular expression filters:
Switch# show inventory | include SN:
PID: C9300-24P , VID: V01 , SN: FOC2345A1BC
Switch# show version | include (Processor board ID|System serial number)
Processor board ID FOC2345A1BC
System serial number : FOC2345A1BC
Identifying Serial Numbers in a Cisco Switch Stack
In Cisco StackWise, StackWise-480, StackWise-160, and FlexStack deployments, multiple physical switches unite into a single logical management entity. Running a standard lookup from the active stack master requires parsing each stack member explicitly.
Step 1: Query All Stack Members Using show inventory
When executed on the active switch, show inventory lists every member chassis sequentially, alongside their respective power supplies and uplink modules:
StackSwitch# show inventory
NAME: "Switch 1", DESCR: "C9300-48U"
PID: C9300-48U , VID: V02 , SN: FOC2412A0AA
NAME: "Switch 2", DESCR: "C9300-48U"
PID: C9300-48U , VID: V02 , SN: FOC2412A0BB
NAME: "Switch 3", DESCR: "C9300-24T"
PID: C9300-24T , VID: V01 , SN: FOC2415A0CC
Step 2: Use show version for Stack-Wide Tabular Summaries
Modern versions of Cisco IOS-XE append a summary table of all stack members directly to the bottom of the show version output:
StackSwitch# show version
...
Switch Ports Model SW Version SW Image Mode Serial Number
------ ----- ----- ---------- ---------- ---- -------------
* 1 52 C9300-48U 17.09.04 CAT9K_IOSXE INSTALL FOC2412A0AA
2 52 C9300-48U 17.09.04 CAT9K_IOSXE INSTALL FOC2412A0BB
3 28 C9300-24T 17.09.04 CAT9K_IOSXE INSTALL FOC2415A0CC
The asterisk (*) designates the switch operating as the current stack master.
Step 3: Correlate Member Numbers with Physical Position
To ensure an RMA replacement or service ticket references the correct unit inside the rack:
1. Run show switch to verify member numbers, priorities, and roles.
2. Run test cable-diagnostics tdr or blink the unit’s beacon LEDs using hw-module beacon switch <member-id> on to confirm the physical chassis corresponding to that member number before unhooking cables.
Checking Serial Numbers on Cisco Nexus Switches (NX-OS)
Cisco Nexus data center switches (such as the Nexus 3000, 7000, and 9000 families) run NX-OS. While standard inventory commands work, NX-OS provides additional commands to read hardware and Serial Programmable Read-Only Memory (SPROM) chips.
Step 1: Run show inventory
As with IOS, show inventory on NX-OS lists the main chassis, supervisor engines, fabric modules, line cards, fan trays, and power supply units:
Nexus-9K# show inventory
NAME: "Chassis", DESCR: "Nexus9000 C93180YC-FX Chassis"
PID: N9K-C93180YC-FX , VID: V02 , SN: FOC22180ABC
NAME: "Slot 1", DESCR: "48x10/25G + 6x40/100G LC"
PID: N9K-C93180YC-FX , VID: V02 , SN: FOC22180ABC
NAME: "Power Supply 1", DESCR: "Nexus9000 C93180YC-FX AC PSU"
PID: NXA-PAC-650W-PI , VID: V01 , SN: LIT21450XYZ
Step 2: Run show hardware
To isolate the physical chassis serial number without scrolling through transceiver and power supply lists, execute:
Nexus-9K# show hardware | include Chassis
cisco Nexus9000 C93180YC-FX Chassis
Chassis Serial Number: FOC22180ABC
Step 3: Extract Raw SPROM Information
For deeper hardware diagnostics or when verifying replaced internal backplanes, NX-OS reads the physical EEPROM SPROM table:
Nexus-9K# show sprom chassis
DISPLAY SPROM Contents of Chassis:
Common code: 0x0064
Major version: 0x01
Minor version: 0x00
...
Product Identifier (PID) : N9K-C93180YC-FX
Version Identifier (VID) : V02
Serial Number (SN) : FOC22180ABC
On modular Nexus switches, append the target module index (e.g., show sprom module 1 or show sprom fabric 1) to audit individual cards.
Extracting Switch Serial Numbers via SNMP
For automated inventory auditing and integration into Network Management Systems (NMS) like Zabbix, PRTG, or LibreNMS, use the standard ENTITY-MIB object entPhysicalSerialNum.
Core OID Reference
entPhysicalSerialNum:.1.3.6.1.2.1.47.1.1.1.1.11entPhysicalName:.1.3.6.1.2.1.47.1.1.1.1.7entPhysicalDescr:.1.3.6.1.2.1.47.1.1.1.1.2
Template: SNMPv2c Chassis Serial Query
# Query all physical entity serial numbers
snmpwalk -v2c -c <COMMUNITY_STRING> <SWITCH_IP> 1.3.6.1.2.1.47.1.1.1.1.11
# Query physical entity names to correlate indexes
snmpwalk -v2c -c <COMMUNITY_STRING> <SWITCH_IP> 1.3.6.1.2.1.47.1.1.1.1.7
Template: SNMPv3 Authenticated Serial Query
snmpwalk -v3 -l authPriv \
-u <SNMP_USER> \
-a SHA -A <AUTH_PASSWORD> \
-x AES -X <PRIV_PASSWORD> \
<SWITCH_IP> 1.3.6.1.2.1.47.1.1.1.1.11
Shell Pipeline: Correlating Entity Description and Serial Number
#!/usr/bin/env bash
TARGET_IP="192.168.1.1"
COMMUNITY="public"
paste \
<(snmpwalk -v2c -c "$COMMUNITY" -Oqv "$TARGET_IP" 1.3.6.1.2.1.47.1.1.1.1.7) \
<(snmpwalk -v2c -c "$COMMUNITY" -Oqv "$TARGET_IP" 1.3.6.1.2.1.47.1.1.1.1.11) \
| awk 'NF > 1 && $2 !~ /^$/ { printf "%-30s : %s\n", $1, $2 }'
Sample Script Output
Chassis : FOC2345A1BC
Power Supply Module 0 : LIT22340XYZ
Switch 1 - Chassis : FOC2345A1BC
TenGigabitEthernet0/1/1 : ONS18420123
Cisco Serial Number Lookup: Warranty and Smart Net Contract Status
Once you have retrieved the switch serial number, use Cisco’s support portals to verify service entitlements, hardware warranty conditions, and lifecycle milestones.
Definition and Verification Purpose
Service coverage verification determines whether a switch is entitled to Cisco Technical Assistance Center (TAC) technical support, hardware Return Material Authorization (RMA) replacements, and licensed Cisco IOS/NX-OS maintenance releases.
Primary Verification Tools
- Cisco Device Coverage Checker:
- Access URL:
cway.cisco.com/sncheck/ - Authentication: Requires a registered Cisco.com (CCO) user account.
- Bulk Capacity: Supports manual entry of up to 20 serial numbers per search.
- Outputs: Current contract status, warranty type, coverage expiration dates, and assigned service contract numbers.
- Cisco Commerce Workspace (CCW) / Service Contract Center (CSCC):
- Access: Enterprise network administrators, procurement teams, and Cisco Certified Partners.
- Outputs: Complete organizational inventory association, contract line items, renewal terms, and Service Level Agreements (SLAs).
- Cisco Support Case Manager (SCM):
- Access URL:
mycase.cloudapps.cisco.com - Purpose: Direct service validation during support ticket generation. Entering an entitled serial number automatically maps existing contracts and valid site delivery addresses for dispatch.
Contract Status Reference
| Status Field | Technical Definition | Operational Entitlement |
|---|---|---|
| Active Covered | Hardware is associated with an active Smart Net Total Care (SNTC) or partner-delivered support contract. | Full TAC access, software bug fixes, and advance hardware replacement (e.g., 8x5xNBD, 24x7x4). |
| Warranty Only | Hardware is covered solely by the base Cisco Enhanced Limited Lifetime Warranty (E-LLW) or standard 90-day warranty. | Basic 90-day TAC assistance; next-business-day hardware shipment where available; no 24×7 phone support. |
| Expired / Uncovered | No active service contract or warranty coverage exists for this serial number. | No TAC case entitlement or hardware replacement; requires contract reinstatement or per-incident billing. |
Lifecycle Milestone Reference
- End of Sale (EoS): The date after which the specific switch model can no longer be ordered through Cisco sales channels.
- End of Software Maintenance (EoSM): The final date that Cisco Engineering releases maintenance patches, security fixes, or OS vulnerability updates for that hardware platform.
- Last Date of Support (LDoS): The final termination date of all support services. Devices that have passed LDoS are not eligible for Smart Net renewals or TAC support.
Finding the serial number on a Cisco switch depends on hardware availability and network access. When handling offline equipment, locate the pull-out luggage tab on the front panel or the rear chassis label. In production networks, execute show inventory to extract accurate chassis, stack, and module serial numbers across Cisco IOS, IOS-XE, and NX-OS devices. Finally, integrate the entPhysicalSerialNum SNMP OID into monitoring pipelines for fleet-wide audits, and use the Cisco Device Coverage Checker to validate ongoing Smart Net support and hardware lifecycle dates.











Comments