CCNA 200-301

CCNP Enterprise

CCNP Security

CCIE Enterprise Lab

CCIE Security Lab

CCNP Service Provider

CCNP Data Center

CCNP Collaboration

CCIE DC Lab

Simply ensure that you have a firm grasp of the IT dumps created by the industry’s greatest IT pros to achieve a 100 percent assured success in the Cisco 300-420 exam. A Cisco credential, as the most valued professional qualification, can open the door to a plethora of job options.

To pass the Cisco 300-420 test on the first try, you must have accurate syllabus information and an excellent study guide. SPOTO 100 percent genuine CCNP 300-420 dumps give you in-depth knowledge of the Cisco 300-420 exam syllabus. This information should be obtained at the outset of your preparation because it will assist you in developing an effective study plan.

To put your skills to the test, try 300-420 free practice questions! Click to join the SPOTO Black Friday Lucky Draw to save more!

CategoriesExam Code100% Pass Dumps
CCNP Enterprise350-401 ENCOR350-401 ENCOR
300-410 ENARSI300-410 ENARSI
300-415 ENSDWI300-415 ENSDWI
300-420 ENSLD300-420 ENSLD
300-425 ENWLSD300-425 ENWLSD
300-430 ENWLSI300-430 ENWLSI
300-435 ENAUTO300-435 ENAUTO

get-lowestprice

NO.1 Which two border nodes are available in the Cisco SD-Access architecture? (Choose two.)

A. extended border
B. edge border
C. internal border
D. anywhere border
E. intermediate border
Answer: CD

NO.2 An engineer must design a multicast network for a financial application. Most of the multicast sources also receive multicast traffic (many-to-many deployment model). To better scale routing tables, the design must not use source trees. Which multicast protocol satisfies these requirements?
A.PIM-SSM
B.PIM-SM
C.MSDP
D.BIDIR-PIM

Answer: D

NO.3 An engineer is tasked with designing a dual BGP peering solution with a service provider. The design must meet these conditions:
• The routers will not learn any prefix with a subnet mask greater than /24.
• The routers will determine the routes to include in the routing table based on the length of the mask alone.
• The routers will make this selection regardless of the service provider configuration.
Which solution should the engineer include in the design?

A.Use a route map and access list to block the desired networks, and apply the route map to BGP neighbors inbound.
B.Use a route map and prefix list to block the desired networks, and apply the route map to BGP neighbors outbound.
C.Use an IP prefix list to block the desired networks and apply the IP prefix list to BGP neighbors outbound.
D.Use an IP prefix list to block the desired networks and apply the IP prefix list to BGP neighbors inbound

Answer: D

NO.4 Which design consideration must be made when dual WAN Edge routers are deployed at a branch site?

A. Use BGP AS-path prepending to influence egress traffic and use MED to influence ingress traffic from the branch.
B.HSRP priorities must match the OMP routing policy to prefer one WAN Edge over the other.
C.Traffic must be symmetrical as it egresses the WAN Edges and returns from remote sites for DPI to function properly.
D.Configure BFD between WAN Edge routers to detect sub-second link failures.

Answer: A

NO.5 Which common issue causes intermittent DMVPN tunnel flaps?

A. a routing neighbor reachability issue
B.a suboptimal routing table
C. interface bandwidth congestion
D.that the GRE tunnel to hub router is not encrypted

Answer: A

black friday offer

Click to join the SPOTO Black Friday Lucky Draw!

NO.6 What is one function of the vSmart controller in an SD-WAN deployment?

A.orchestrates vEdge and cEdge connectivity
B.responsible for the centralized control plane of the SD-WAN network
C.provides centralized network management and a GUI to monitor and operate the SD-WAN overlay
D.provides a data-plane at branch offices to pass traffic through the SD-WAN network

Answer: B

NO.7 Which feature is required for graceful restart to recover from a processor failure?
A. Cisco Express Forwarding
B. Virtual Switch System
C. Stateful Switchover
D. Bidirectional Forwarding Detection

Answer: C

NO.8 Which type of rendezvous point deployment is standards-based and support dynamic RP discovery?
A. Auto-RP
B. Anycast-RP
C. bootstrap router
D. static RP

Answer: C

NO.9 At which layer does Cisco Express Forwarding use adjacency tables to populate addressing information?
A. Layer4
B. Layer 2
C. Layer 1
D. Layer 3

Answer: B

NO.10 Which two routing protocols allow for unequal cost load balancing? (Choose two.)
A.EIGRP
B.IS-IS
C.BGP
D.OSPF
E.RIPng

Answer: AC

Conclusion

SPOTO provides practice tests to help you prepare for the Cisco 300-420 certification exam. After receiving input from successful candidates, our experts and Cisco Certified Network Professional specialists created practice questions. All Cisco 300-420 test questions are syllabus-based, and they will help you pass the 300-420 exam quickly.

get-lowestprice

Latest Passing Report-100% Pass Guarantee

Recommend Exam Study Materials:

Free CCNP 300-410 Practice Test Questions and Answers
Free Access to CCNA CBROPS 200-201 Practice Test
Free CCNA 200-901 Practice Test Questions and Answers
Download Free CCNP 350-901 Practice Test Questions
Success Tips for CCNP Security 350 701 SCOR Exam Using Practice Tests
How to Pass CCNA 200-301 with Dumps-Free Practice Test Q&A
Black Friday Sale: Don’t Miss Lowest Price 2021 on All SPOTO Products
Free CCNP 300-410 Practice Test Questions and Answers
Free Access to CCNA CBROPS 200-201 Practice Test
Please follow and like us:
Last modified: November 16, 2021

Author

Comments

Write a Reply or Comment

Your email address will not be published.