{"id":24621,"date":"2026-11-17T17:57:23","date_gmt":"2026-11-17T09:57:23","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html"},"modified":"2026-11-17T17:57:23","modified_gmt":"2026-11-17T09:57:23","slug":"how-to-check-root-bridge-in-cisco-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html","title":{"rendered":"How to Check Root Bridge in Cisco Switch"},"content":{"rendered":"<p>Every Layer 2 Ethernet network running Spanning Tree Protocol (STP) relies on a single logical focal point: the root bridge. Because all loop-free forwarding paths are calculated relative to this switch, knowing which device holds the root role is essential for troubleshooting suboptimal traffic flows, unexpected link blocking, and topology flaps. On a Cisco switch, you can quickly verify whether your local chassis is the root bridge, inspect per-VLAN elections, trace an upstream root device across the network, and correct misconfigured priorities directly from the CLI.<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#How_to_Verify_If_Your_Local_Cisco_Switch_Is_the_Root_Bridge\" title=\"How to Verify If Your Local Cisco Switch Is the Root Bridge\">How to Verify If Your Local Cisco Switch Is the Root Bridge<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_1_Inspect_the_Detailed_Spanning-Tree_State\" title=\"Step 1: Inspect the Detailed Spanning-Tree State\">Step 1: Inspect the Detailed Spanning-Tree State<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_2_Check_the_Multi-VLAN_Root_Summary_Table\" title=\"Step 2: Check the Multi-VLAN Root Summary Table\">Step 2: Check the Multi-VLAN Root Summary Table<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Understanding_Root_Bridge_Election_Fields_Priority_System_ID_and_MAC_Address\" title=\"Understanding Root Bridge Election Fields: Priority, System ID, and MAC Address\">Understanding Root Bridge Election Fields: Priority, System ID, and MAC Address<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#What_determines_which_Cisco_switch_becomes_the_root_bridge\" title=\"What determines which Cisco switch becomes the root bridge?\">What determines which Cisco switch becomes the root bridge?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#What_is_the_difference_between_Root_ID_and_Bridge_ID_in_the_CLI_output\" title=\"What is the difference between Root ID and Bridge ID in the CLI output?\">What is the difference between Root ID and Bridge ID in the CLI output?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Why_does_a_Cisco_switch_display_a_priority_like_32769_instead_of_32768\" title=\"Why does a Cisco switch display a priority like 32769 instead of 32768?\">Why does a Cisco switch display a priority like 32769 instead of 32768?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#When_does_the_MAC_address_decide_the_root_bridge_election\" title=\"When does the MAC address decide the root bridge election?\">When does the MAC address decide the root bridge election?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#CLI_Templates_to_Check_the_Root_Bridge_for_Specific_VLANs\" title=\"CLI Templates to Check the Root Bridge for Specific VLANs\">CLI Templates to Check the Root Bridge for Specific VLANs<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#How_to_Trace_a_Remote_Root_Bridge_Using_the_Root_Port_and_CDP\" title=\"How to Trace a Remote Root Bridge Using the Root Port and CDP\">How to Trace a Remote Root Bridge Using the Root Port and CDP<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_1_Identify_the_Target_Root_MAC_Address_and_Local_Root_Port\" title=\"Step 1: Identify the Target Root MAC Address and Local Root Port\">Step 1: Identify the Target Root MAC Address and Local Root Port<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_2_Resolve_Port-Channels_to_Physical_Interfaces\" title=\"Step 2: Resolve Port-Channels to Physical Interfaces\">Step 2: Resolve Port-Channels to Physical Interfaces<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_3_Query_CDP_or_LLDP_on_the_Physical_Root_Port\" title=\"Step 3: Query CDP or LLDP on the Physical Root Port\">Step 3: Query CDP or LLDP on the Physical Root Port<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_4_Fallback_to_the_MAC_Address_Table_If_CDP_Is_Disabled\" title=\"Step 4: Fallback to the MAC Address Table If CDP Is Disabled\">Step 4: Fallback to the MAC Address Table If CDP Is Disabled<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_5_Hop_to_the_Upstream_Neighbor_and_Repeat\" title=\"Step 5: Hop to the Upstream Neighbor and Repeat\">Step 5: Hop to the Upstream Neighbor and Repeat<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#How_to_Configure_and_Change_the_Root_Bridge_on_a_Cisco_Switch\" title=\"How to Configure and Change the Root Bridge on a Cisco Switch\">How to Configure and Change the Root Bridge on a Cisco Switch<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_1_Connect_to_the_Intended_Primary_Core_or_Distribution_Switch\" title=\"Step 1: Connect to the Intended Primary Core or Distribution Switch\">Step 1: Connect to the Intended Primary Core or Distribution Switch<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_2_Set_the_Root_Bridge_Using_Either_a_Macro_or_Static_Priority\" title=\"Step 2: Set the Root Bridge Using Either a Macro or Static Priority\">Step 2: Set the Root Bridge Using Either a Macro or Static Priority<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Step_3_Verify_the_Election_and_Save_the_Configuration\" title=\"Step 3: Verify the Election and Save the Configuration\">Step 3: Verify the Election and Save the Configuration<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Cisco_CLI_Command_Reference_and_Platform_Variations\" title=\"Cisco CLI Command Reference and Platform Variations\">Cisco CLI Command Reference and Platform Variations<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Command_Syntax_Specification_Cisco_IOS_IOS_XE\" title=\"Command Syntax Specification (Cisco IOS \/ IOS XE)\">Command Syntax Specification (Cisco IOS \/ IOS XE)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Verification_Modifier_Definitions\" title=\"Verification Modifier Definitions\">Verification Modifier Definitions<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\/#Platform_Comparison_Cisco_IOS_XE_vs_Cisco_NX-OS\" title=\"Platform Comparison: Cisco IOS XE vs. Cisco NX-OS\">Platform Comparison: Cisco IOS XE vs. Cisco NX-OS<\/a><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Verify_If_Your_Local_Cisco_Switch_Is_the_Root_Bridge\"><\/span>How to Verify If Your Local Cisco Switch Is the Root Bridge<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>To check whether the Cisco switch you are currently logged into is acting as the root bridge, inspect its spanning-tree state from privileged EXEC mode using two primary verification commands.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Inspect_the_Detailed_Spanning-Tree_State\"><\/span>Step 1: Inspect the Detailed Spanning-Tree State<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run the base <code>show spanning-tree<\/code> command to view the election data and port states:<\/p>\n<pre><code class=\"language-text\">Switch# show spanning-tree\n\nVLAN0001\n  Spanning tree enabled protocol rstp\n  Root ID    Priority    32769\n             Address     001c.58a1.b200\n             This bridge is the root\n             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec\n\n  Bridge ID  Priority    32769  (priority 32768 sys-id-ext 1)\n             Address     001c.58a1.b200\n             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec\n             Aging Time  300 sec\n\nInterface           Role Sts Cost      Prio.Nbr Type\n------------------- ---- --- --------- -------- --------------------------------\nGi1\/0\/1             Desg FWD 4         128.1    P2p\nGi1\/0\/2             Desg FWD 4         128.2    P2p\n<\/code><\/pre>\n<p>Look for three indicators in this output to confirm that the local switch is the root bridge:<\/p>\n<ol>\n<li><strong>Explicit Root Declaration:<\/strong> Under the <code>Root ID<\/code> header, the third line explicitly states <code>This bridge is the root<\/code>. If another switch is the root bridge, this line is replaced by <code>Cost<\/code> and <code>Port<\/code> entries pointing toward the upstream root.<\/li>\n<li><strong>Matching MAC Addresses:<\/strong> The hardware <code>Address<\/code> listed under <code>Root ID<\/code> (<code>001c.58a1.b200<\/code>) is identical to the <code>Address<\/code> listed under the local <code>Bridge ID<\/code> section.<\/li>\n<li><strong>All Designated Port Roles:<\/strong> In the interface table at the bottom, every active spanning-tree port displays a <code>Role<\/code> of <code>Desg<\/code> (Designated) in the <code>FWD<\/code> (Forwarding) state. A root bridge never has a port with the <code>Root<\/code> or <code>Altn<\/code> (Alternate\/Blocking) role for that VLAN.<\/li>\n<\/ol>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_the_Multi-VLAN_Root_Summary_Table\"><\/span>Step 2: Check the Multi-VLAN Root Summary Table<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When a switch carries dozens of VLANs, scrolling through the full output is inefficient. Run <code>show spanning-tree root<\/code> to generate a condensed table showing the root status across all active VLANs at once:<\/p>\n<pre><code class=\"language-text\">Switch# show spanning-tree root\n\n                                        Root    Hello Max Fwd\nVlan                   Root ID          Cost    Time  Age Dly  Root Port\n---------------- -------------------- --------- ----- --- ---  ------------\nVLAN0001         32769 001c.58a1.b200         0    2   20  15  This bridge is the root\nVLAN0010         24586 0024.97c4.1100         4    2   20  15  Gi1\/0\/24\nVLAN0020         32788 001c.58a1.b200         0    2   20  15  This bridge is the root\n<\/code><\/pre>\n<p>Evaluate two columns in this summary view:<br \/>\n* <strong>Root Cost:<\/strong> A value of <code>0<\/code> confirms you are logged directly into the root bridge for that VLAN. Any non-zero number (such as <code>4<\/code> on <code>VLAN0010<\/code>) represents the cumulative path cost required to reach a remote root bridge.<br \/>\n* <strong>Root Port:<\/strong> If the local switch is the root, this column states <code>This bridge is the root<\/code>. Otherwise, it displays the local egress interface (such as <code>Gi1\/0\/24<\/code>) used to reach the upstream root switch.<\/p>\n<p><strong>Key Takeaway:<\/strong> Always check <code>show spanning-tree root<\/code> first for an immediate, multi-VLAN overview of whether <code>Root Cost<\/code> is <code>0<\/code> and <code>Root Port<\/code> reports <code>This bridge is the root<\/code>.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Understanding_Root_Bridge_Election_Fields_Priority_System_ID_and_MAC_Address\"><\/span>Understanding Root Bridge Election Fields: Priority, System ID, and MAC Address<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While reading the <code>show spanning-tree<\/code> output above, several numerical fields\u2014such as <code>Priority 32769<\/code> and separate <code>Root ID<\/code> versus <code>Bridge ID<\/code> blocks\u2014govern how the switch arrived at its current role. The following questions explain how Cisco switches calculate and compare these values.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"What_determines_which_Cisco_switch_becomes_the_root_bridge\"><\/span>What determines which Cisco switch becomes the root bridge?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Spanning Tree Protocol elects the root bridge by comparing the 8-byte <strong>Bridge ID (BID)<\/strong> advertised inside Configuration BPDUs by every switch in a broadcast domain. The switch with the <strong>lowest numerical Bridge ID<\/strong> wins the election. The Bridge ID is evaluated from left to right: first by comparing the 2-byte Priority field, and if priorities are equal, by comparing the 6-byte supervisor MAC address.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"What_is_the_difference_between_Root_ID_and_Bridge_ID_in_the_CLI_output\"><\/span>What is the difference between Root ID and Bridge ID in the CLI output?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Root ID<\/strong> displays the priority, MAC address, and active STP timers of the switch that has currently won the election for that VLAN across the entire Layer 2 topology.<\/li>\n<li><strong>Bridge ID<\/strong> displays the local switch&#8217;s own priority, MAC address, and configured timers for that VLAN. When the local switch is not the root, comparing <code>Bridge ID<\/code> against <code>Root ID<\/code> reveals whether your local switch lost the election due to a higher priority number or a higher hexadecimal MAC address.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Why_does_a_Cisco_switch_display_a_priority_like_32769_instead_of_32768\"><\/span>Why does a Cisco switch display a priority like 32769 instead of 32768?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Modern Cisco switches run Per-VLAN Spanning Tree and enable the <strong>Extended System ID<\/strong> (<code>spanning-tree extend system-id<\/code>) by default so the chassis does not need to burn a separate hardware MAC address for every VLAN. This feature splits the 16-bit Priority field into a 4-bit <strong>Base Priority<\/strong> (configurable only in increments of <code>4096<\/code>, with an IEEE 802.1D default of <code>32768<\/code>) and a 12-bit <strong>Extended System ID<\/strong> carrying the VLAN number:<\/p>\n<p>$$\\text{Displayed Priority} = \\text{Base Priority} + \\text{VLAN ID}$$<\/p>\n<p>For VLAN 1 at default settings, the displayed priority is $32768 + 1 = 32769$ (shown in the CLI as <code>priority 32768 sys-id-ext 1<\/code>). For VLAN 10, the default priority becomes $32768 + 10 = 32778$.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"When_does_the_MAC_address_decide_the_root_bridge_election\"><\/span>When does the MAC address decide the root bridge election?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If every switch on the network is left at the default base priority of <code>32768<\/code>, every switch calculates the exact same total priority for a given VLAN. STP breaks this tie by electing the switch with the <strong>lowest hexadecimal MAC address<\/strong>. Because IEEE OUI blocks are assigned chronologically, the oldest switch on the network typically possesses the lowest MAC address\u2014meaning an unconfigured network will almost always elect an aging, low-bandwidth access switch as its root bridge.<\/p>\n<p><strong>Key Takeaway:<\/strong> A switch wins the root bridge election by advertising the lowest total Bridge ID, which combines the base priority (in multiples of 4096), the VLAN ID, and the chassis MAC address as a tie-breaker.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"CLI_Templates_to_Check_the_Root_Bridge_for_Specific_VLANs\"><\/span>CLI Templates to Check the Root Bridge for Specific VLANs<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Because Cisco switches run Per-VLAN Spanning Tree (PVST+ or Rapid-PVST+) by default, different switches often act as the root bridge for different VLANs to load-balance uplinks. Use the following CLI templates to query individual VLANs and filter root status without scrolling through irrelevant data.<\/p>\n<pre><code class=\"language-text\">! 1. Check full root ID, local bridge ID, and port roles for a single VLAN\nshow spanning-tree vlan &lt;vlan-id&gt;\n\n! 2. Check ONLY the winning Root ID, path cost, and root port for a specific VLAN or range\nshow spanning-tree vlan &lt;vlan-id-or-range&gt; root\n\n! 3. Check ONLY the local switch's Bridge ID and priority for a specific VLAN\nshow spanning-tree vlan &lt;vlan-id&gt; bridge\n\n! 4. Filter output across all VLANs to list only VLAN headers and root declarations\nshow spanning-tree | include ^VLAN|This bridge is the root|Root ID|Address\n\n! 5. Filter the root summary table to show only VLANs where this switch is NOT the root\nshow spanning-tree root | exclude This bridge is the root\n<\/code><\/pre>\n<p>Replace <code>&lt;vlan-id&gt;<\/code> with a single number (such as <code>10<\/code>) or <code>&lt;vlan-id-or-range&gt;<\/code> with a comma-separated list or hyphenated range (such as <code>10,20,30-40<\/code>) to audit primary and secondary distribution switches side by side.<\/p>\n<p><strong>Key Takeaway:<\/strong> Scoping verification commands with the <code>vlan &lt;id&gt;<\/code> keyword and regex output filters (<code>include<\/code>\/<code>exclude<\/code>) isolates per-VLAN root roles immediately in large Rapid-PVST+ topologies.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Trace_a_Remote_Root_Bridge_Using_the_Root_Port_and_CDP\"><\/span>How to Trace a Remote Root Bridge Using the Root Port and CDP<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When the local switch does not display <code>This bridge is the root<\/code>, you must trace the Layer 2 path upstream to find which physical chassis holds the root role. Follow these sequential steps to locate the remote root switch.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Identify_the_Target_Root_MAC_Address_and_Local_Root_Port\"><\/span>Step 1: Identify the Target Root MAC Address and Local Root Port<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run <code>show spanning-tree vlan &lt;vlan-id&gt;<\/code> on the local switch and note two pieces of data from the <code>Root ID<\/code> section: the root bridge&#8217;s MAC <code>Address<\/code> and the local <code>Port<\/code> pointing toward it.<\/p>\n<pre><code class=\"language-text\">Switch# show spanning-tree vlan 10\n\nVLAN0010\n  Spanning tree enabled protocol rstp\n  Root ID    Priority    24586\n             Address     0024.97c4.1100\n             Cost        4\n             Port        28 (Port-channel1)\n             Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec\n<\/code><\/pre>\n<p>Here, the remote root bridge has the MAC address <code>0024.97c4.1100<\/code>, and the local switch reaches it out <strong>Port-channel1<\/strong> (<code>Po1<\/code>).<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Resolve_Port-Channels_to_Physical_Interfaces\"><\/span>Step 2: Resolve Port-Channels to Physical Interfaces<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If the Root Port is a logical EtherChannel (<code>Po1<\/code>) rather than a standalone physical interface, identify its underlying physical member ports:<\/p>\n<pre><code class=\"language-text\">Switch# show etherchannel summary | include Po1\n1      Po1(SU)         LACP      Gi1\/0\/23(P)    Gi1\/0\/24(P)\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Query_CDP_or_LLDP_on_the_Physical_Root_Port\"><\/span>Step 3: Query CDP or LLDP on the Physical Root Port<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Use Cisco Discovery Protocol (CDP) or Link Layer Discovery Protocol (LLDP) on one of the physical root interfaces to identify the directly connected upstream switch and its management IP address:<\/p>\n<pre><code class=\"language-text\">Switch# show cdp neighbors GigabitEthernet1\/0\/23 detail\n\nDevice ID: DIST-SW01.corp.local\nEntry address(es): \n  IP address: 10.10.1.2\nPlatform: cisco C9300-24T,  Capabilities: Switch IGMP \nInterface: GigabitEthernet1\/0\/23,  Port ID (outgoing port): GigabitEthernet1\/0\/1\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Fallback_to_the_MAC_Address_Table_If_CDP_Is_Disabled\"><\/span>Step 4: Fallback to the MAC Address Table If CDP Is Disabled<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>In environments where CDP and LLDP are disabled for security, query the Layer 2 MAC address table for the Root ID MAC address (or inspect MAC addresses learned on the Root Port) to verify the forwarding path:<\/p>\n<pre><code class=\"language-text\">Switch# show mac address-table address 0024.97c4.1100\n          Mac Address Table\n-------------------------------------------\nVlan    Mac Address       Type        Ports\n----    -----------       ----        -----\n  10    0024.97c4.1100    DYNAMIC     Po1\n<\/code><\/pre>\n<p><em>Note:<\/em> A Cisco switch uses a base chassis MAC pool for spanning-tree BPDUs that may differ by the last hex byte from its SVIs, or may only appear in the CAM table if it actively sources data-plane frames. Even if the exact STP base MAC is not cached in the CAM table, the Root Port identified in Step 1 (<code>Po1<\/code>) always points directly toward the root bridge.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Hop_to_the_Upstream_Neighbor_and_Repeat\"><\/span>Step 5: Hop to the Upstream Neighbor and Repeat<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>SSH into the upstream switch discovered in Step 3 (<code>10.10.1.2<\/code>) and run <code>show spanning-tree vlan 10 root<\/code>. If that switch reports <code>This bridge is the root<\/code>, you have found the physical root switch. If it lists another Root Port, repeat Steps 3 and 5 along each upstream Root Port until <code>Cost<\/code> reaches <code>0<\/code>.<\/p>\n<p><strong>Key Takeaway:<\/strong> Following the <code>Root Port<\/code> upstream via <code>show cdp neighbors &lt;interface&gt; detail<\/code> will lead you directly to the physical root bridge in any loop-free topology.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Configure_and_Change_the_Root_Bridge_on_a_Cisco_Switch\"><\/span>How to Configure and Change the Root Bridge on a Cisco Switch<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>If your trace reveals that an access-layer closet switch has accidentally won the root election, you should immediately migrate the root role to your core or distribution switches. Follow this procedure to enforce a deterministic root bridge placement.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Connect_to_the_Intended_Primary_Core_or_Distribution_Switch\"><\/span>Step 1: Connect to the Intended Primary Core or Distribution Switch<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Log into the switch that should act as the primary focal point for your topology (typically the same chassis acting as the active HSRP, VRRP, or GLBP default gateway for those VLANs) and enter global configuration mode:<\/p>\n<pre><code class=\"language-text\">Core-SW01# configure terminal\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Set_the_Root_Bridge_Using_Either_a_Macro_or_Static_Priority\"><\/span>Step 2: Set the Root Bridge Using Either a Macro or Static Priority<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>You can promote the switch using one of two configuration methods. Avoid mixing both methods across the same VLANs.<\/p>\n<h4>Option A: Set a Static Priority Value (Recommended Best Practice)<\/h4>\n<p>Setting a low, explicit priority value guarantees that the switch remains the root bridge even if other switches with modified priorities are later introduced into the network. Priority values must be entered in increments of <code>4096<\/code> (from <code>0<\/code> to <code>61440<\/code>):<\/p>\n<pre><code class=\"language-text\">! On the Primary Core Switch (sets base priority to 4096)\nCore-SW01(config)# spanning-tree vlan 1-100 priority 4096\n\n! On the Secondary\/Redundant Core Switch (sets base priority to 8192)\nCore-SW02(config)# spanning-tree vlan 1-100 priority 8192\n<\/code><\/pre>\n<h4>Option B: Use the <code>root primary<\/code> and <code>root secondary<\/code> Macros<\/h4>\n<p>Alternatively, Cisco provides a one-time configuration macro that inspects the current <code>Root ID<\/code> on the wire at the moment you press Enter:<\/p>\n<pre><code class=\"language-text\">! On the Primary Core Switch\nCore-SW01(config)# spanning-tree vlan 1-100 root primary\n\n! On the Secondary\/Redundant Core Switch\nCore-SW02(config)# spanning-tree vlan 1-100 root secondary\n<\/code><\/pre>\n<p>When you execute <code>root primary<\/code>, the switch checks the current root bridge&#8217;s base priority:<br \/>\n* If the current root&#8217;s base priority is higher than <code>24576<\/code> (such as the default <code>32768<\/code>), the macro writes <code>spanning-tree vlan &lt;id&gt; priority 24576<\/code> into the running configuration.<br \/>\n* If the current root&#8217;s base priority is already <code>24576<\/code> or lower, the macro sets the local switch&#8217;s priority to <code>4096<\/code> less than the current root (down to a minimum of <code>4096<\/code>).<br \/>\n* The <code>root secondary<\/code> macro statically sets the local base priority to <code>28672<\/code>, assuming the rest of the network remains at the default <code>32768<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Verify_the_Election_and_Save_the_Configuration\"><\/span>Step 3: Verify the Election and Save the Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Exit configuration mode, verify that the local switch has preempted the old root bridge, and write the changes to NVRAM:<\/p>\n<pre><code class=\"language-text\">Core-SW01(config)# end\nCore-SW01# show spanning-tree vlan 10 root\nCore-SW01# copy running-config startup-config\n<\/code><\/pre>\n<p><strong>Key Takeaway:<\/strong> Explicitly configuring <code>priority 4096<\/code> on your primary core switch and <code>priority 8192<\/code> on your secondary core switch provides deterministic root bridge placement that will not be overridden by default switches.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_CLI_Command_Reference_and_Platform_Variations\"><\/span>Cisco CLI Command Reference and Platform Variations<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>This reference defines the complete syntax modifiers for spanning-tree verification across Cisco operating systems and highlights behavior differences between Cisco Catalyst (IOS \/ IOS XE) and Cisco Nexus (NX-OS) platforms.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Command_Syntax_Specification_Cisco_IOS_IOS_XE\"><\/span>Command Syntax Specification (Cisco IOS \/ IOS XE)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">show spanning-tree [active | backbonefast | blockedports | bridge | detail | inconsistentports | interface &lt;type&gt; &lt;number&gt; | mst | pathcost method | root | summary | uplinkfast | vlan &lt;vlan-id&gt;]\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Verification_Modifier_Definitions\"><\/span>Verification Modifier Definitions<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong><code>active<\/code><\/strong>: Displays spanning-tree information exclusively for interfaces that are currently up and participating in STP forwarding or blocking states.<\/li>\n<li><strong><code>blockedports<\/code><\/strong>: Lists only interfaces currently held in a blocking or discarding state by STP.<\/li>\n<li><strong><code>bridge<\/code><\/strong>: Displays only the local switch&#8217;s Bridge ID, priority, MAC address, and STP timer parameters across active instances.<\/li>\n<li><strong><code>detail<\/code><\/strong>: Outputs comprehensive per-port diagnostics, including BPDU transmit\/receive counters, port path cost, port identifier, and designated bridge\/root IDs advertised on each segment.<\/li>\n<li><strong><code>inconsistentports<\/code><\/strong>: Lists interfaces placed into a <code>Root-Inconsistent<\/code> (via Root Guard) or <code>Loop-Inconsistent<\/code> (via Loop Guard) blocking state.<\/li>\n<li><strong><code>mst<\/code><\/strong>: Displays Multiple Spanning Tree Protocol (IEEE 802.1s) instance mappings, regional root IDs, and internal Spanning Tree (IST) status when running <code>spanning-tree mode mst<\/code>.<\/li>\n<li><strong><code>root<\/code><\/strong>: Displays only the elected Root ID, root path cost, root timers, and local Root Port per VLAN.<\/li>\n<li><strong><code>summary<\/code><\/strong>: Displays global STP operational mode (PVST+, Rapid-PVST+, or MSTP), extended system ID state, PortFast defaults, and aggregate port state counts per VLAN.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Platform_Comparison_Cisco_IOS_XE_vs_Cisco_NX-OS\"><\/span>Platform Comparison: Cisco IOS XE vs. Cisco NX-OS<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Attribute<\/th>\n<th style=\"text-align: left;\">Cisco Catalyst (IOS \/ IOS XE)<\/th>\n<th style=\"text-align: left;\">Cisco Nexus (NX-OS)<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Default STP Mode<\/strong><\/td>\n<td style=\"text-align: left;\"><code>rapid-pvst<\/code> (IEEE 802.1w per VLAN)<\/td>\n<td style=\"text-align: left;\"><code>rapid-pvst<\/code> (IEEE 802.1w per VLAN)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Check Root Summary<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree root<\/code><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree root<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Check Specific VLAN<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree vlan &lt;id&gt;<\/code><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree vlan &lt;id&gt;<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Check MSTP Root<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree mst [&lt;instance-id&gt;]<\/code><\/td>\n<td style=\"text-align: left;\"><code>show spanning-tree mst [&lt;instance-id&gt;]<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Root Cost Calculation Default<\/strong><\/td>\n<td style=\"text-align: left;\">Short (32-bit, 10 Gbps = <code>2<\/code>) unless <code>spanning-tree pathcost method long<\/code> is configured<\/td>\n<td style=\"text-align: left;\">Short by default; supports <code>spanning-tree pathcost method long<\/code> (20 Gbps = <code>1000<\/code>, 10 Gbps = <code>2000<\/code>)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Virtual Port-Channel (vPC) Root Behavior<\/strong><\/td>\n<td style=\"text-align: left;\">N\/A (Uses StackWise Virtual \/ VSS, acting as a single control plane)<\/td>\n<td style=\"text-align: left;\">Dual control plane; requires <code>spanning-tree pseudo-information<\/code> when aligning Root ID across vPC peers<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Official Cisco Documentation Reference<\/strong><\/td>\n<td style=\"text-align: left;\"><em>Cisco IOS LAN Switching Command Reference<\/em> (<code>show spanning-tree<\/code> chapter)<\/td>\n<td style=\"text-align: left;\"><em>Cisco Nexus 9000 Series NX-OS Layer 2 Switching Command Reference<\/em><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Key Takeaway:<\/strong> While basic <code>show spanning-tree root<\/code> and <code>vlan &lt;id&gt;<\/code> commands are identical across IOS XE and NX-OS, always account for pathcost calculation methods and vPC <code>pseudo-information<\/code> configurations when auditing hybrid Catalyst and Nexus data centers.<\/p>\n<hr \/>\n<p>Auditing your spanning-tree root bridge should be a routine part of any Cisco network health check. By starting with <code>show spanning-tree root<\/code> to verify local root costs, understanding how Base Priority and Extended System ID form the Bridge ID, tracing unexpected Root Ports upstream via CDP, and locking in explicit priorities on your core switches, you ensure your Layer 2 topology stays predictable, resilient, and loop-free.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-root-bridge-in-cisco-switch_24621.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+Root+Bridge+in+Cisco+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\",\"How to Check Root Bridge in Cisco Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Every Layer 2 Ethernet network running Spanning Tree Protocol (STP) relies on a single logical focal point: the root bridge. Because all loop-free forwarding paths are calculated relative to this switch, knowing which device holds the root role is essential for troubleshooting suboptimal traffic flows, unexpected link blocking, and topology flaps. On a Cisco switch,&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check Root Bridge in Cisco Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check Root Bridge in Cisco Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Every Layer 2 Ethernet network running Spanning Tree Protocol (STP) relies on a single logical focal point: the root bridge. Because all loop-free forwarding paths are calculated relative to this switch, knowing which device holds the root role is essential for troubleshooting suboptimal traffic flows, unexpected link blocking, and topology flaps. On a Cisco switch,... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T09:57:23+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"13 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\",\"name\":\"How to Check Root Bridge in Cisco Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T09:57:23+00:00\",\"dateModified\":\"2026-11-17T09:57:23+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check Root Bridge in Cisco Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check Root Bridge in Cisco Switch\",\"datePublished\":\"2026-11-17T09:57:23+00:00\",\"dateModified\":\"2026-11-17T09:57:23+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage\"},\"wordCount\":1969,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check Root Bridge in Cisco Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html","og_locale":"en_US","og_type":"article","og_title":"How to Check Root Bridge in Cisco Switch - SPOTO Official Blog","og_description":"Every Layer 2 Ethernet network running Spanning Tree Protocol (STP) relies on a single logical focal point: the root bridge. Because all loop-free forwarding paths are calculated relative to this switch, knowing which device holds the root role is essential for troubleshooting suboptimal traffic flows, unexpected link blocking, and topology flaps. On a Cisco switch,... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T09:57:23+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"13 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html","name":"How to Check Root Bridge in Cisco Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T09:57:23+00:00","dateModified":"2026-11-17T09:57:23+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check Root Bridge in Cisco Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check Root Bridge in Cisco Switch","datePublished":"2026-11-17T09:57:23+00:00","dateModified":"2026-11-17T09:57:23+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#webpage"},"wordCount":1969,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-root-bridge-in-cisco-switch_24621.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24621"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24621"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24621\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24621"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24621"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24621"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}