{"id":24615,"date":"2026-11-17T17:49:08","date_gmt":"2026-11-17T09:49:08","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html"},"modified":"2026-11-17T17:49:08","modified_gmt":"2026-11-17T09:49:08","slug":"how-to-check-pvdm-on-cisco-router","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html","title":{"rendered":"How to Check PVDM on Cisco Router"},"content":{"rendered":"<p>Packet Voice Digital Signal Processor Modules (PVDMs) provide the hardware digital signal processing (DSP) power required by Cisco routers to terminate analog and digital time-division multiplexing (TDM) voice circuits, perform codec transcoding, host hardware conference bridges, and anchor Media Termination Points (MTPs). Whether you are auditing hardware before a Unified Communications migration, sizing Cisco Unified Border Element (CUBE) transcoding capacity, or diagnosing call setup failures, verifying both the physical PVDM state and real-time DSP channel utilization is a core administrative task.<\/p>\n<p>Checking a PVDM involves verifying physical hardware recognition at the chassis level, inspecting logical DSP core health and credit allocation inside Cisco IOS or IOS-XE, and monitoring active media sessions.<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Verifying_Physical_PVDM_Installation_via_CLI\" title=\"Verifying Physical PVDM Installation via CLI\">Verifying Physical PVDM Installation via CLI<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_1_Check_Hardware_PID_Version_and_Serial_Number_with_show_inventory\" title=\"Step 1: Check Hardware PID, Version, and Serial Number with show inventory\">Step 1: Check Hardware PID, Version, and Serial Number with show inventory<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_2_Verify_Subslot_Operational_State_with_show_platform_IOS-XE\" title=\"Step 2: Verify Subslot Operational State with show platform (IOS-XE)\">Step 2: Verify Subslot Operational State with show platform (IOS-XE)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_3_Inspect_Detailed_Board_Diagnostics_with_show_diag_Classic_IOS\" title=\"Step 3: Inspect Detailed Board Diagnostics with show diag (Classic IOS)\">Step 3: Inspect Detailed Board Diagnostics with show diag (Classic IOS)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_4_Confirm_Voice_Subsystem_Registration_with_show_voice_dsp_summary\" title=\"Step 4: Confirm Voice Subsystem Registration with show voice dsp summary\">Step 4: Confirm Voice Subsystem Registration with show voice dsp summary<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Checking_PVDMs_Across_Platforms_ISR_G2_vs_ISR_4000_and_Catalyst_8300\" title=\"Checking PVDMs Across Platforms: ISR G2 vs. ISR 4000 and Catalyst 8300\">Checking PVDMs Across Platforms: ISR G2 vs. ISR 4000 and Catalyst 8300<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#1_Legacy_ISR_G1_and_ISR_G2_2800_3800_2900_3900_Series\" title=\"1. Legacy ISR G1 and ISR G2 (2800, 3800, 2900, 3900 Series)\">1. Legacy ISR G1 and ISR G2 (2800, 3800, 2900, 3900 Series)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#2_Cisco_ISR_4000_Series_IOS-XE\" title=\"2. Cisco ISR 4000 Series (IOS-XE)\">2. Cisco ISR 4000 Series (IOS-XE)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#3_Cisco_Catalyst_8300_Series_and_ISR_4461_NIM-PVDM_and_SM-X-PVDM\" title=\"3. Cisco Catalyst 8300 Series and ISR 4461 (NIM-PVDM and SM-X-PVDM)\">3. Cisco Catalyst 8300 Series and ISR 4461 (NIM-PVDM and SM-X-PVDM)<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Checking_PVDM_DSP_Utilization_Credits_and_Active_Channels\" title=\"Checking PVDM DSP Utilization, Credits, and Active Channels\">Checking PVDM DSP Utilization, Credits, and Active Channels<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_1_Audit_DSP_Health_and_Credit_Pools_with_show_voice_dsp_group_all\" title=\"Step 1: Audit DSP Health and Credit Pools with show voice dsp group all\">Step 1: Audit DSP Health and Credit Pools with show voice dsp group all<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_2_View_Per-Channel_Call_Activity_with_show_voice_dsp\" title=\"Step 2: View Per-Channel Call Activity with show voice dsp\">Step 2: View Per-Channel Call Activity with show voice dsp<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_3_Check_Transcoding_and_Conferencing_Profiles_with_show_dspfarm_all\" title=\"Step 3: Check Transcoding and Conferencing Profiles with show dspfarm all\">Step 3: Check Transcoding and Conferencing Profiles with show dspfarm all<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Troubleshooting_Undetected_or_Failed_PVDM_Modules\" title=\"Troubleshooting Undetected or Failed PVDM Modules\">Troubleshooting Undetected or Failed PVDM Modules<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_1_Diagnose_Abnormal_DSP_States_FAIL_DOWN_or_APP_DOWNLOADING\" title=\"Step 1: Diagnose Abnormal DSP States (FAIL, DOWN, or APP_DOWNLOADING)\">Step 1: Diagnose Abnormal DSP States (FAIL, DOWN, or APP_DOWNLOADING)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_2_Perform_a_Soft_CLI_Reset_of_the_PVDM_or_DSP_Core\" title=\"Step 2: Perform a Soft CLI Reset of the PVDM or DSP Core\">Step 2: Perform a Soft CLI Reset of the PVDM or DSP Core<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_3_Isolate_a_Failed_DSP_Core_During_Production_Hours\" title=\"Step 3: Isolate a Failed DSP Core During Production Hours\">Step 3: Isolate a Failed DSP Core During Production Hours<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Step_4_Verify_Slot_Compatibility_Licensing_and_Physical_Reseating_Rules\" title=\"Step 4: Verify Slot Compatibility, Licensing, and Physical Reseating Rules\">Step 4: Verify Slot Compatibility, Licensing, and Physical Reseating Rules<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#SNMP_OIDs_and_Templates_for_Automated_PVDM_Monitoring\" title=\"SNMP OIDs and Templates for Automated PVDM Monitoring\">SNMP OIDs and Templates for Automated PVDM Monitoring<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Cisco_IOS_IOS-XE_SNMP_Configuration_Template\" title=\"Cisco IOS \/ IOS-XE SNMP Configuration Template\">Cisco IOS \/ IOS-XE SNMP Configuration Template<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#CISCO-DSP-MGMT-MIB_Key_OID_Reference_Template\" title=\"CISCO-DSP-MGMT-MIB Key OID Reference Template\">CISCO-DSP-MGMT-MIB Key OID Reference Template<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Net-SNMP_CLI_Polling_Script_Template\" title=\"Net-SNMP CLI Polling Script Template\">Net-SNMP CLI Polling Script Template<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Cisco_IOS_Voice_Command_Reference_and_Documentation_Guide\" title=\"Cisco IOS Voice Command Reference and Documentation Guide\">Cisco IOS Voice Command Reference and Documentation Guide<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-24\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#show_voice_dsp\" title=\"show voice dsp\">show voice dsp<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-25\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#show_dspfarm\" title=\"show dspfarm\">show dspfarm<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-26\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Official_Cisco_Documentation_Navigation_Paths\" title=\"Official Cisco Documentation Navigation Paths\">Official Cisco Documentation Navigation Paths<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-27\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Verifying_Physical_PVDM_Installation_via_CLI\"><\/span>Verifying Physical PVDM Installation via CLI<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>To confirm whether a PVDM is physically installed in a Cisco router, recognized by the chassis backplane, and reporting a valid part number (PID) and serial number, follow this sequential CLI verification process.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Check_Hardware_PID_Version_and_Serial_Number_with_show_inventory\"><\/span>Step 1: Check Hardware PID, Version, and Serial Number with <code>show inventory<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The primary command across both classic Cisco IOS and modern Cisco IOS-XE platforms to verify physical PVDM presence is <code>show inventory<\/code>. This command reads the onboard EEPROM of every detected module and outputs its exact slot location, product identifier (PID), hardware revision (VID), and factory serial number (SN).<\/p>\n<pre><code class=\"language-text\">Router# show inventory\nNAME: &quot;Chassis&quot;, DESCR: &quot;Cisco ISR4331 Chassis&quot;\nPID: ISR4331\/K9        , VID: V02, SN: FDO2012XXXX\n\nNAME: &quot;PVDM subslot 0\/4&quot;, DESCR: &quot;PVDM4-64 Voice DSP Module&quot;\nPID: PVDM4-64          , VID: V01, SN: FOC1945XXXX\n\nNAME: &quot;subslot 0\/1 db module 0&quot;, DESCR: &quot;PVDM4-32 Voice DSP Module&quot;\nPID: PVDM4-32          , VID: V02, SN: FOC1833XXXX\n<\/code><\/pre>\n<p>If your router has multiple interface cards, filter the output directly using <code>show inventory | include PVDM<\/code> or <code>show inventory | section PVDM<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Verify_Subslot_Operational_State_with_show_platform_IOS-XE\"><\/span>Step 2: Verify Subslot Operational State with <code>show platform<\/code> (IOS-XE)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On Cisco IOS-XE routers, physical detection in the inventory should be paired with <code>show platform<\/code> to confirm that the router&#8217;s chassis manager has initialized the PVDM subslot into an <code>ok<\/code> operational state:<\/p>\n<pre><code class=\"language-text\">Router# show platform\nChassis type: ISR4331\/K9\n\nSlot      Type                State                 Insert time (ago)\n--------- ------------------- --------------------- -----------------\n0         ISR4331\/K9          ok                    42d05h\n 0\/0      ISR4331-3x1GE       ok                    42d05h\n 0\/1      NIM-2MFT-T1\/E1      ok                    42d05h\n 0\/4      PVDM4-64            ok                    42d05h\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Inspect_Detailed_Board_Diagnostics_with_show_diag_Classic_IOS\"><\/span>Step 3: Inspect Detailed Board Diagnostics with <code>show diag<\/code> (Classic IOS)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On legacy Cisco IOS routers (such as the 2800, 3800, 2900, and 3900 series), <code>show platform<\/code> does not display subslot-level PVDM states. Instead, run <code>show diag<\/code> to view the motherboard PVDM SIMM sockets, EEPROM contents, and hardware assembly numbers:<\/p>\n<pre><code class=\"language-text\">Router# show diag | section PVDM\n        Slot 0:\n        PVDM2-64 SIMM (4 DSP) daughter card\n          Hardware Revision        : 4.0\n          Part Number              : 73-8539-04\n          Board Revision           : B0\n          Serial Number            : FOC1422XXXX\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Confirm_Voice_Subsystem_Registration_with_show_voice_dsp_summary\"><\/span>Step 4: Confirm Voice Subsystem Registration with <code>show voice dsp summary<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Once hardware detection is confirmed, run <code>show voice dsp summary<\/code> (or inspect the active configuration via <code>show running-config | section voice-card<\/code>) to ensure the IOS voice subsystem has bound a logical <code>voice-card<\/code> construct to the physical PVDM slot. Physical detection paired with an active <code>voice-card<\/code> entry proves the module is ready to allocate DSP channels.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Checking_PVDMs_Across_Platforms_ISR_G2_vs_ISR_4000_and_Catalyst_8300\"><\/span>Checking PVDMs Across Platforms: ISR G2 vs. ISR 4000 and Catalyst 8300<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While <code>show inventory<\/code> works across all routers, the physical placement, naming conventions, and architectural rules for PVDMs differ significantly as you move from legacy ISR G2 routers to Cisco ISR 4000 and Catalyst 8300 Series Edge Platforms. Use this platform progression to interpret CLI slot outputs accurately.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"1_Legacy_ISR_G1_and_ISR_G2_2800_3800_2900_3900_Series\"><\/span>1. Legacy ISR G1 and ISR G2 (2800, 3800, 2900, 3900 Series)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On ISR G1 and G2 routers, PVDM2 and PVDM3 modules are installed directly into dedicated PVDM slots on the router motherboard (<code>Slot 0<\/code>).<br \/>\n&#8211; <strong>Architecture Rule:<\/strong> Motherboard PVDMs on ISR G2 serve a unified pool. A single motherboard PVDM3 can simultaneously provide TDM voice termination (for T1\/E1 VWICs) and IP media services (transcoding and conferencing).<br \/>\n&#8211; <strong>CLI Identification:<\/strong> Appears in <code>show inventory<\/code> under <code>Slot 0<\/code> as <code>PVDM2-xx<\/code> or <code>PVDM3-xx<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"2_Cisco_ISR_4000_Series_IOS-XE\"><\/span>2. Cisco ISR 4000 Series (IOS-XE)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The ISR 4000 architecture splits PVDM4 deployment into two distinct physical locations\u2014and understanding which slot you see in the CLI determines what services that PVDM can perform:<br \/>\n&#8211; <strong>Motherboard PVDM4 (<code>PVDM subslot 0\/4<\/code>):<\/strong> All ISR 4000 models except the ISR 4221 and ISR 4461 include a single onboard motherboard PVDM4 slot, which always enumerates as subslot <code>0\/4<\/code>. A motherboard PVDM4 <strong>cannot<\/strong> be used for TDM voice termination; it is restricted exclusively to IP-based media services such as transcoding, conferencing, and media optimization.<br \/>\n&#8211; <strong>T1\/E1 NIM-Mounted PVDM4 (<code>subslot 0\/x db module 0<\/code>):<\/strong> To terminate TDM T1\/E1 PRI or CAS circuits on an ISR 4000, a PVDM4 daughterboard must be physically mounted onto the Fourth-Generation T1\/E1 Voice and WAN Network Interface Module (such as <code>NIM-1MFT-T1\/E1<\/code> or <code>NIM-2MFT-T1\/E1<\/code>). In <code>show inventory<\/code>, this displays as <code>subslot 0\/&lt;nim-slot&gt; db module 0<\/code>. Any unused DSP channels on the NIM-mounted PVDM4 can overflow to assist the motherboard with IP transcoding or conferencing once <code>dsp services dspfarm<\/code> is enabled under that <code>voice-card<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"3_Cisco_Catalyst_8300_Series_and_ISR_4461_NIM-PVDM_and_SM-X-PVDM\"><\/span>3. Cisco Catalyst 8300 Series and ISR 4461 (NIM-PVDM and SM-X-PVDM)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The Catalyst 8300 Series and the high-end ISR 4461 do not have motherboard PVDM slots. Instead, they rely on dedicated slot-based DSP modules for IP media services (requiring Cisco IOS-XE 17.3 or later):<br \/>\n&#8211; <strong>Standalone <code>NIM-PVDM<\/code> (<code>NIM-PVDM-32<\/code>, <code>-64<\/code>, <code>-128<\/code>, <code>-256<\/code>):<\/strong> Installs directly into a standard NIM slot without needing a T1\/E1 carrier card. It supports IP media services only (no TDM voice termination).<br \/>\n&#8211; <strong>High-Density <code>SM-X-PVDM<\/code> (<code>SM-X-PVDM-500<\/code>, <code>-1000<\/code>, <code>-2000<\/code>, <code>-3000<\/code>):<\/strong> Installs into a Service Module (SM-X) slot on Catalyst 8300 or ISR 4331\/4351\/4451\/4461 platforms, scaling up to 3,080 low-complexity channels per module.<br \/>\n&#8211; <strong>CLI Identification:<\/strong> Run <code>show platform<\/code> to confirm the NIM or SM-X slot state, and check <code>show inventory<\/code> where the module enumerates directly under its NIM or SM subslot (for example, <code>Subslot 0\/2: NIM-PVDM-128<\/code>). Note that analog modules (FXS\/FXO) and BRI modules on ISR 4000 and Catalyst 8300 have built-in, non-configurable DSP chips and do not consume channels from installed PVDM4 or NIM-PVDM cards.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Checking_PVDM_DSP_Utilization_Credits_and_Active_Channels\"><\/span>Checking PVDM DSP Utilization, Credits, and Active Channels<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Confirming that a PVDM is installed only tells you theoretical capacity. Because modern PVDMs allocate resources dynamically using a credit-based &#8220;Flex DSP&#8221; architecture, you must inspect the voice DSP groups and DSP farm profiles to see how many channels and credits are actively consumed and how much headroom remains.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Audit_DSP_Health_and_Credit_Pools_with_show_voice_dsp_group_all\"><\/span>Step 1: Audit DSP Health and Credit Pools with <code>show voice dsp group all<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run <code>show voice dsp group all<\/code> to inspect every DSP chip across all installed PVDMs. Each PVDM contains one or more individual DSP cores, and each core provides a fixed pool of credits (for example, 240 credits per DSP core on many PVDM3\/PVDM4 modules).<\/p>\n<pre><code class=\"language-text\">Router# show voice dsp group all\nDSP groups on slot 0\/4:\ndsp 1:\n  State: UP, firmware: 4.4.706\n  Max signal\/voice channel: 16\/16\n  Max credits: 240\n  Group: FLEX_GROUP_VOICE, complexity: FLEX\n    Shared credits: 180, reserved credits: 0\n    Signaling channels allocated: 2\n    Voice channels allocated: 2\n    Credits used: 30\n  Group: FLEX_GROUP_XCODE, complexity: SECURE MEDIUM\n    Shared credits: 0, reserved credits: 60\n    Transcoding channels allocated: 1\n    Credits used: 30\n\n  0 DSP resource allocation failure\n<\/code><\/pre>\n<p>Evaluate the following key metrics in the output:<br \/>\n1. <strong><code>State: UP<\/code>:<\/strong> Confirms the DSP core has booted and loaded its firmware.<br \/>\n2. <strong><code>Max credits<\/code> vs. <code>Shared credits<\/code> \/ <code>reserved credits<\/code>:<\/strong> <code>Max credits<\/code> is the total capacity of that DSP chip. When you configure a <code>dspfarm profile<\/code> for transcoding or conferencing, IOS reserves credits (<code>reserved credits<\/code>) exclusively for that profile. Remaining credits stay in <code>Shared credits<\/code> for TDM voice termination.<br \/>\n3. <strong><code>Channels allocated<\/code> and <code>Credits used<\/code>:<\/strong> Shows real-time utilization. Low-complexity calls (such as G.711) consume fewer credits per channel than medium- or high-complexity calls (such as G.729 or iLBC). To calculate free capacity on a DSP core, subtract <code>Credits used<\/code> (and any dedicated <code>reserved credits<\/code> locked by other groups) from <code>Max credits<\/code>.<br \/>\n4. <strong><code>DSP resource allocation failure<\/code>:<\/strong> Located at the bottom of the output. Any number greater than <code>0<\/code> indicates that the router rejected a call or transcoding request because the PVDM ran out of DSP credits.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_View_Per-Channel_Call_Activity_with_show_voice_dsp\"><\/span>Step 2: View Per-Channel Call Activity with <code>show voice dsp<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To see exactly which voice ports or RTP streams are occupying individual DSP channels\u2014along with the negotiated codec, packet counts, and signaling channel ID\u2014run <code>show voice dsp<\/code> (or <code>show voice dsp active<\/code> to filter out idle channels):<\/p>\n<pre><code class=\"language-text\">Router# show voice dsp active\nTYPE  DSP CH CODEC     VERS TS ABORT PACK-TX\/RX      VOICE-PORT CHNL\n===== === == ========= ==== == ===== =============== ========== ====\nFLEX  001 01 g711ulaw  4.4  01     0    4510\/4508    0\/1\/0:23   001\nFLEX  001 02 g729r8    4.4  02     0    1204\/1204    0\/1\/0:23   002\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Check_Transcoding_and_Conferencing_Profiles_with_show_dspfarm_all\"><\/span>Step 3: Check Transcoding and Conferencing Profiles with <code>show dspfarm all<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When PVDMs are registered to Cisco Unified Communications Manager (CUCM via SCCP) or local CUBE (via LTI or SCCP) for transcoding, conferencing, or hardware MTP, inspect profile status and session usage with <code>show dspfarm all<\/code> and <code>show dspfarm dsp all<\/code>:<\/p>\n<pre><code class=\"language-text\">Router# show dspfarm all\nDspfarm Profile Configuration\n\n Profile ID = 1, Service = TRANSCODING, Resource ID = 1\n Profile Description :\n Profile Service Mode : Non Secure\n Profile Admin State : UP\n Profile Operation State : ACTIVE\n Application : CUBE   Status : ASSOCIATED\n Resource Provider : FLEX_DSPFARM   Status : UP\n Number of Resource Configured : 12\n Number of Resource Available : 10\n Codec Configuration: num_of_codecs:4\n Codec : g711ulaw, Maximum Packetization Period : 30\n Codec : g711alaw, Maximum Packetization Period : 30\n Codec : g729ar8, Maximum Packetization Period : 60\n Codec : g729abr8, Maximum Packetization Period : 60\n<\/code><\/pre>\n<p>Look closely at <code>Number of Resource Configured<\/code> versus <code>Number of Resource Available<\/code> to determine how many concurrent transcoding or conferencing sessions remain free in your allocated pool. Selecting the key operational metric here reveals whether your DSP bottleneck is physical hardware exhaustion (<code>Max credits<\/code> reached) or administrative profile sizing (<code>maximum sessions<\/code> set too low in the <code>dspfarm profile<\/code>).<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Troubleshooting_Undetected_or_Failed_PVDM_Modules\"><\/span>Troubleshooting Undetected or Failed PVDM Modules<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>If a PVDM fails to appear in <code>show inventory<\/code> as covered above, or if <code>show voice dsp group all<\/code> reports unresponsive DSP cores, follow this diagnostic workflow to recover the module without causing unnecessary network downtime.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Diagnose_Abnormal_DSP_States_FAIL_DOWN_or_APP_DOWNLOADING\"><\/span>Step 1: Diagnose Abnormal DSP States (<code>FAIL<\/code>, <code>DOWN<\/code>, or <code>APP_DOWNLOADING<\/code>)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When checking <code>show voice dsp group all<\/code>, any state other than <code>UP<\/code> indicates a fault:<br \/>\n&#8211; <strong><code>FAIL<\/code> or <code>DOWN<\/code>:<\/strong> A DSP core has crashed, experienced repeated <code>DSP_TIMEOUT<\/code> IPC errors, or suffered a hardware fault. Any voice call routed to a failed DSP core will immediately drop or fail to cut through audio.<br \/>\n&#8211; <strong><code>APP_DOWNLOADING<\/code> or <code>booting<\/code>:<\/strong> The router is attempting to push DSP firmware to the module, or the module is stuck in a boot loop. If it remains in <code>APP_DOWNLOADING<\/code> for more than a few minutes, firmware transfer over the internal bus has hung.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Perform_a_Soft_CLI_Reset_of_the_PVDM_or_DSP_Core\"><\/span>Step 2: Perform a Soft CLI Reset of the PVDM or DSP Core<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Before scheduling a physical power outage, attempt a software reload of the affected DSP or subslot:<br \/>\n&#8211; <strong>On Cisco ISR 4000 and Catalyst 8300 (IOS-XE):<\/strong> Reload the specific PVDM subslot using its slot\/subslot coordinates:<br \/>\n  <code>text<br \/>\n  Router# hw-module subslot 0\/4 reload<\/code><br \/>\n&#8211; <strong>On Legacy ISR G1 and ISR G2 (Classic IOS):<\/strong> Reset the individual hung DSP chip without resetting the entire router:<br \/>\n  <code>text<br \/>\n  Router# test dsp device 0 1 reset<\/code><br \/>\n  <em>(Where <code>0<\/code> is the slot number and <code>1<\/code> is the DSP ID shown in <code>show voice dsp group all<\/code>.)<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Isolate_a_Failed_DSP_Core_During_Production_Hours\"><\/span>Step 3: Isolate a Failed DSP Core During Production Hours<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If a single DSP core on a multi-DSP PVDM fails during business hours and a soft reset does not bring it back to <code>UP<\/code>, the router may still attempt to allocate calls to that broken DSP, causing intermittent call failures. Take the defective subslot or DSP core out of service immediately so active calls only use healthy DSPs:<br \/>\n&#8211; <strong>On Cisco ISR 4000 and Catalyst 8300 (IOS-XE):<\/strong><br \/>\n  <code>text<br \/>\n  Router# hw-module subslot 0\/4 stop<\/code><br \/>\n&#8211; <strong>On Legacy ISR G1 and ISR G2 (Classic IOS):<\/strong><br \/>\n  <code>text<br \/>\n  Router# test dsp device 0 1 remove<\/code><br \/>\n  <em>(Once replaced or recovered, <code>test dsp device &lt;slot&gt; &lt;dsp-id&gt; restore<\/code> returns it to the pool on classic IOS.)<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Verify_Slot_Compatibility_Licensing_and_Physical_Reseating_Rules\"><\/span>Step 4: Verify Slot Compatibility, Licensing, and Physical Reseating Rules<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If a newly installed PVDM does not appear in <code>show inventory<\/code> or <code>show platform<\/code> at all, check these four physical and software prerequisites:<br \/>\n1. <strong>Incompatible Slot Placement:<\/strong> Ensure a PVDM3 was not forced into an ISR 4000 (which requires PVDM4), and confirm you are not expecting a motherboard PVDM4 (<code>subslot 0\/4<\/code>) to terminate TDM T1\/E1 voice calls (TDM cards require the PVDM4 to be mounted directly on the T1\/E1 NIM).<br \/>\n2. <strong>Minimum IOS-XE Version and UC License:<\/strong> Standalone <code>NIM-PVDM<\/code> modules require Cisco IOS-XE 17.3.1 or later. Additionally, voice DSP initialization requires the Unified Communications (<code>uck9<\/code>) technology package license to be active on the router (<code>show license summary<\/code> or <code>show version<\/code>).<br \/>\n3. <strong>Physical Reseating and Hot-Swap (OIR) Rules:<\/strong> Dust or uneven pin contact during shipping frequently causes missing PVDMs. While PVDM4 daughterboards mounted on T1\/E1 NIMs support Online Insertion and Removal (OIR) when the NIM is gracefully stopped, <strong>motherboard PVDM4 modules are not hot-swappable<\/strong>. You must completely power down the router during a maintenance window before removing or reseating a motherboard PVDM.<br \/>\n4. <strong>Hardware RMA Validation:<\/strong> If reseating the card and upgrading firmware fail to clear a <code>FAIL<\/code> state\u2014or if the PVDM works in a known-good chassis but stays stuck in <code>booting<\/code> on the target router\u2014initiate a Cisco Return Material Authorization (RMA) for the defective PVDM or chassis backplane.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"SNMP_OIDs_and_Templates_for_Automated_PVDM_Monitoring\"><\/span>SNMP OIDs and Templates for Automated PVDM Monitoring<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>To continuously track DSP channel utilization and alert on failed DSP cores without manually running CLI commands, configure your Network Monitoring System (NMS) to poll <code>CISCO-DSP-MGMT-MIB<\/code> (Base OID: <code>.1.3.6.1.4.1.9.9.86<\/code>).<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Cisco_IOS_IOS-XE_SNMP_Configuration_Template\"><\/span>Cisco IOS \/ IOS-XE SNMP Configuration Template<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-ios\">! Enable SNMPv3 Read-Only access and DSP traps on the Cisco router\nsnmp-server view DSP-MONITOR iso included\nsnmp-server group NMS-GROUP v3 priv read DSP-MONITOR\nsnmp-server user NMS-POLLER NMS-GROUP v3 auth sha &lt;AUTH_PASSWORD&gt; priv aes 128 &lt;PRIV_PASSWORD&gt;\nsnmp-server enable traps dsp card-status\nsnmp-server enable traps dsp oper-state\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"CISCO-DSP-MGMT-MIB_Key_OID_Reference_Template\"><\/span><code>CISCO-DSP-MGMT-MIB<\/code> Key OID Reference Template<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-ini\"># Card-Level PVDM Metrics (cdspCardStatusTable)\n# Indexed by entPhysicalIndex from ENTITY-MIB (.1.3.6.1.2.1.47.1.1.1.1.7)\ncdspCardState                = .1.3.6.1.4.1.9.9.86.1.1.1.1.2   ; 1=normal, 2=warning, 3=critical, 4=fatal, 5=offLine\ncdspCardResourceUtilization  = .1.3.6.1.4.1.9.9.86.1.1.1.1.3   ; Percentage (0..100%) of total card DSP channels in use\ncdspTotalDsp                 = .1.3.6.1.4.1.9.9.86.1.1.1.1.7   ; Total DSP cores present on the card\ncdspFailedDsp                = .1.3.6.1.4.1.9.9.86.1.1.1.1.8   ; Number of DSP cores currently in a failed state\n\n# Per-DSP Core Channel Utilization Metrics (cdspStatusTable)\ncdspOperState                = .1.3.6.1.4.1.9.9.86.1.2.1.1.1   ; 1=normal, 2=shutdown, 3=congested, 4=failed\ncdspTotalChannels            = .1.3.6.1.4.1.9.9.86.1.2.1.1.6   ; Maximum channels supported by this DSP core\ncdspInUseChannels            = .1.3.6.1.4.1.9.9.86.1.2.1.1.7   ; Channels currently reserved for call setup\ncdspActiveChannels           = .1.3.6.1.4.1.9.9.86.1.2.1.1.8   ; Channels actively processing voice\/media packets\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Net-SNMP_CLI_Polling_Script_Template\"><\/span>Net-SNMP CLI Polling Script Template<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-bash\">#!\/usr\/bin\/env bash\n# Poll Cisco Router PVDM utilization and DSP channel counts via SNMPv3\nROUTER_IP=&quot;&lt;ROUTER_IP&gt;&quot;\nSNMP_USER=&quot;NMS-POLLER&quot;\nAUTH_PASS=&quot;&lt;AUTH_PASSWORD&gt;&quot;\nPRIV_PASS=&quot;&lt;PRIV_PASSWORD&gt;&quot;\n\necho &quot;=== PVDM Card Utilization (%) ===&quot;\nsnmpwalk -v3 -l authPriv -u &quot;$SNMP_USER&quot; -a SHA -A &quot;$AUTH_PASS&quot; -x AES -X &quot;$PRIV_PASS&quot; \\\n  &quot;$ROUTER_IP&quot; .1.3.6.1.4.1.9.9.86.1.1.1.1.3\n\necho &quot;=== Failed DSP Cores Count ===&quot;\nsnmpwalk -v3 -l authPriv -u &quot;$SNMP_USER&quot; -a SHA -A &quot;$AUTH_PASS&quot; -x AES -X &quot;$PRIV_PASS&quot; \\\n  &quot;$ROUTER_IP&quot; .1.3.6.1.4.1.9.9.86.1.1.1.1.8\n\necho &quot;=== Per-DSP Reserved Channels (cdspInUseChannels) ===&quot;\nsnmpwalk -v3 -l authPriv -u &quot;$SNMP_USER&quot; -a SHA -A &quot;$AUTH_PASS&quot; -x AES -X &quot;$PRIV_PASS&quot; \\\n  &quot;$ROUTER_IP&quot; .1.3.6.1.4.1.9.9.86.1.2.1.1.7\n\necho &quot;=== Per-DSP Active Voice Channels (cdspActiveChannels) ===&quot;\nsnmpwalk -v3 -l authPriv -u &quot;$SNMP_USER&quot; -a SHA -A &quot;$AUTH_PASS&quot; -x AES -X &quot;$PRIV_PASS&quot; \\\n  &quot;$ROUTER_IP&quot; .1.3.6.1.4.1.9.9.86.1.2.1.1.8\n<\/code><\/pre>\n<p>Setting an NMS threshold alert whenever <code>cdspFailedDsp<\/code> (<code>.1.3.6.1.4.1.9.9.86.1.1.1.1.8<\/code>) exceeds <code>0<\/code> or <code>cdspCardResourceUtilization<\/code> (<code>.1.3.6.1.4.1.9.9.86.1.1.1.1.3<\/code>) exceeds <code>85%<\/code> ensures proactive notification before call drops occur.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_IOS_Voice_Command_Reference_and_Documentation_Guide\"><\/span>Cisco IOS Voice Command Reference and Documentation Guide<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The following specifications provide the exact command syntax, privilege modes, argument definitions, and authoritative Cisco documentation locations for PVDM and voice DSP verification commands.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"show_voice_dsp\"><\/span><code>show voice dsp<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Description:<\/strong> Displays the operational status, firmware version, credit allocation, or channel-level packet statistics for voice DSP modules.<\/li>\n<li><strong>Syntax:<\/strong> <code>show voice dsp [group {all | slot &lt;slot-number&gt;} | active | summary | detail | crash-dump]<\/code><\/li>\n<li><strong>Command Mode:<\/strong> User EXEC (<code>&gt;<\/code>) or Privileged EXEC (<code>#<\/code>).<\/li>\n<li><strong>Key Keyword Definitions:<\/strong><\/li>\n<li><code>group all<\/code>: Displays credit pools, shared\/reserved credits, and allocated channels for all DSP groups across all slots.<\/li>\n<li><code>active<\/code>: Filters output to show only DSP channels currently processing an active voice or media call.<\/li>\n<li><code>summary<\/code>: Displays a condensed table of DSP count and channel totals per <code>voice-card<\/code>.<\/li>\n<li><code>crash-dump<\/code>: Displays diagnostic memory register dumps for DSP cores that have transitioned to a <code>FAIL<\/code> state.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"show_dspfarm\"><\/span><code>show dspfarm<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Description:<\/strong> Displays configured DSP farm profiles, SCCP\/LTI application associations, and DSP resource pool allocations for transcoding, conferencing, and hardware MTP services.<\/li>\n<li><strong>Syntax:<\/strong> <code>show dspfarm [all | profile [&lt;profile-id&gt;] | dsp [all | active | stats]]<\/code><\/li>\n<li><strong>Command Mode:<\/strong> Privileged EXEC (<code>#<\/code>).<\/li>\n<li><strong>Key Keyword Definitions:<\/strong><\/li>\n<li><code>all<\/code>: Outputs all DSP farm configuration parameters and current resource availability counters.<\/li>\n<li><code>profile<\/code>: Displays administrative state (<code>UP<\/code>\/<code>DOWN<\/code>), operational state (<code>ACTIVE<\/code>\/<code>INACTIVE<\/code>), associated application (<code>CUBE<\/code> or <code>SCCP<\/code>), and configured codecs for a specific profile.<\/li>\n<li><code>dsp all<\/code>: Lists individual DSP channels assigned to DSP farm pools and their current session states.<\/li>\n<li><code>dsp stats<\/code>: Displays packet-level transmit\/receive statistics for active DSP farm sessions.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Official_Cisco_Documentation_Navigation_Paths\"><\/span>Official Cisco Documentation Navigation Paths<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To access complete field-by-field descriptions and hardware installation rules on Cisco.com, consult these official manuals:<br \/>\n1. <strong>Command Syntax and Field Reference:<\/strong> <em>Cisco IOS Voice Command Reference<\/em> \u2192 Navigate to <strong>Chapter: S Commands<\/strong> \u2192 Locate <code>show dspfarm<\/code> and <code>show voice dsp<\/code> (<code>show vdev through show voice statistics memory-usage<\/code>).<br \/>\n2. <strong>Voice Card and DSP Farm Configuration:<\/strong> <em>Cisco IOS Voice Command Reference<\/em> \u2192 Navigate to <strong>Chapter: D through I Commands<\/strong> \u2192 Locate <code>dsp services dspfarm<\/code> and <code>dspfarm (voice-card)<\/code>.<br \/>\n3. <strong>CUBE Transcoding and DSP Verification:<\/strong> <em>Cisco Unified Border Element Configuration Guide (Cisco IOS XE)<\/em> \u2192 Navigate to <strong>Media Manipulation and Profiles<\/strong> \u2192 <strong>DSP-Based Functionality Including Transcoding and Transrating<\/strong>.<br \/>\n4. <strong>Hardware Architecture and Channel Density Tables:<\/strong> <em>Cisco Packet Voice Digital Signal Processor Modules (PVDM4, NIM-PVDM, and SM-X-PVDM) Data Sheet<\/em> and <em>Configure and Troubleshoot PVDM4 on Cisco ISR 4000 Series Routers<\/em> (Cisco Support Document ID: <code>213250<\/code> \/ <code>118749<\/code>).<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Verifying a PVDM on a Cisco router requires checking both physical hardware state and logical DSP resource pools. Start by confirming physical detection and slot placement using <code>show inventory<\/code> and <code>show platform<\/code>, keeping in mind the architectural separation between motherboard PVDM4 slots, T1\/E1 NIM daughterboards, and standalone <code>NIM-PVDM<\/code> or <code>SM-X-PVDM<\/code> modules on modern IOS-XE routers. From there, use <code>show voice dsp group all<\/code> and <code>show dspfarm all<\/code> to audit credit consumption and active media sessions, and integrate <code>CISCO-DSP-MGMT-MIB<\/code> into your monitoring platform so you always have visibility into your voice gateway capacity.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-pvdm-on-cisco-router_24615.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+PVDM+on+Cisco+Router+https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\",\"How to Check PVDM on Cisco Router\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Packet Voice Digital Signal Processor Modules (PVDMs) provide the hardware digital signal processing (DSP) power required by Cisco routers to terminate analog and digital time-division multiplexing (TDM) voice circuits, perform codec transcoding, host hardware conference bridges, and anchor Media Termination Points (MTPs). Whether you are auditing hardware before a Unified Communications migration, sizing Cisco Unified&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check PVDM on Cisco Router - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check PVDM on Cisco Router - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Packet Voice Digital Signal Processor Modules (PVDMs) provide the hardware digital signal processing (DSP) power required by Cisco routers to terminate analog and digital time-division multiplexing (TDM) voice circuits, perform codec transcoding, host hardware conference bridges, and anchor Media Termination Points (MTPs). Whether you are auditing hardware before a Unified Communications migration, sizing Cisco Unified... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T09:49:08+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"15 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\",\"name\":\"How to Check PVDM on Cisco Router - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T09:49:08+00:00\",\"dateModified\":\"2026-11-17T09:49:08+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check PVDM on Cisco Router\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check PVDM on Cisco Router\",\"datePublished\":\"2026-11-17T09:49:08+00:00\",\"dateModified\":\"2026-11-17T09:49:08+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage\"},\"wordCount\":2070,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check PVDM on Cisco Router - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html","og_locale":"en_US","og_type":"article","og_title":"How to Check PVDM on Cisco Router - SPOTO Official Blog","og_description":"Packet Voice Digital Signal Processor Modules (PVDMs) provide the hardware digital signal processing (DSP) power required by Cisco routers to terminate analog and digital time-division multiplexing (TDM) voice circuits, perform codec transcoding, host hardware conference bridges, and anchor Media Termination Points (MTPs). Whether you are auditing hardware before a Unified Communications migration, sizing Cisco Unified... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T09:49:08+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"15 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html","name":"How to Check PVDM on Cisco Router - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T09:49:08+00:00","dateModified":"2026-11-17T09:49:08+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check PVDM on Cisco Router"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check PVDM on Cisco Router","datePublished":"2026-11-17T09:49:08+00:00","dateModified":"2026-11-17T09:49:08+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#webpage"},"wordCount":2070,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-pvdm-on-cisco-router_24615.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24615"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24615"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24615\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24615"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24615"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24615"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}