{"id":24593,"date":"2026-11-17T17:06:38","date_gmt":"2026-11-17T09:06:38","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html"},"modified":"2026-11-17T17:06:38","modified_gmt":"2026-11-17T09:06:38","slug":"how-to-check-ospf-cost-on-cisco-router","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html","title":{"rendered":"How to Check OSPF Cost on Cisco Router"},"content":{"rendered":"<p>Open Shortest Path First (OSPF) determines the best path through a network by evaluating a single metric: <strong>cost<\/strong>. On a Cisco router, every OSPF-enabled interface is assigned an individual link cost based on its bandwidth, and the router sums these outgoing link costs along a path to compute the cumulative metric installed in the IP routing table. <\/p>\n<p>When validating network designs, preparing for CCNA or CCNP certification exams, or diagnosing why traffic is taking a slower backup circuit, knowing where to inspect both individual interface costs and end-to-end route metrics is essential. Below, you will find how Cisco calculates default OSPF metrics, the exact CLI commands to check them, platform syntax differences across IOS and NX-OS, step-by-step configuration methods to adjust path selection, and solutions to common metric anomalies.<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#How_Cisco_Calculates_Default_OSPF_Cost_and_Reference_Bandwidth\" title=\"How Cisco Calculates Default OSPF Cost and Reference Bandwidth\">How Cisco Calculates Default OSPF Cost and Reference Bandwidth<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Cisco_CLI_Commands_to_Check_OSPF_Interface_and_Route_Cost\" title=\"Cisco CLI Commands to Check OSPF Interface and Route Cost\">Cisco CLI Commands to Check OSPF Interface and Route Cost<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Cisco_OSPF_Command_Reference_IOS_IOS-XE_and_NX-OS_Syntax\" title=\"Cisco OSPF Command Reference: IOS, IOS-XE, and NX-OS Syntax\">Cisco OSPF Command Reference: IOS, IOS-XE, and NX-OS Syntax<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Command_Syntax_Specification\" title=\"Command Syntax Specification\">Command Syntax Specification<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Output_Field_Definitions\" title=\"Output Field Definitions\">Output Field Definitions<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Platform_Default_Differences_IOSIOS-XE_vs_NX-OS\" title=\"Platform Default Differences (IOS\/IOS-XE vs. NX-OS)\">Platform Default Differences (IOS\/IOS-XE vs. NX-OS)<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#How_to_Change_OSPF_Cost_on_a_Cisco_Router\" title=\"How to Change OSPF Cost on a Cisco Router\">How to Change OSPF Cost on a Cisco Router<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Step_1_Scale_Costs_Globally_Using_auto-cost_reference-bandwidth_Recommended_Baseline\" title=\"Step 1: Scale Costs Globally Using auto-cost reference-bandwidth (Recommended Baseline)\">Step 1: Scale Costs Globally Using auto-cost reference-bandwidth (Recommended Baseline)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Step_2_Override_Cost_on_a_Specific_Interface_Using_ip_ospf_cost_For_Traffic_Engineering\" title=\"Step 2: Override Cost on a Specific Interface Using ip ospf cost (For Traffic Engineering)\">Step 2: Override Cost on a Specific Interface Using ip ospf cost (For Traffic Engineering)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Step_3_Adjust_Nominal_Interface_Bandwidth_Using_bandwidth_Use_with_Caution\" title=\"Step 3: Adjust Nominal Interface Bandwidth Using bandwidth (Use with Caution)\">Step 3: Adjust Nominal Interface Bandwidth Using bandwidth (Use with Caution)<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Cisco_OSPF_Cost_and_Verification_CLI_Cheat_Sheet\" title=\"Cisco OSPF Cost and Verification CLI Cheat Sheet\">Cisco OSPF Cost and Verification CLI Cheat Sheet<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Troubleshooting_Unexpected_OSPF_Path_Costs_and_Suboptimal_Routing\" title=\"Troubleshooting Unexpected OSPF Path Costs and Suboptimal Routing\">Troubleshooting Unexpected OSPF Path Costs and Suboptimal Routing<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Why_is_OSPF_routing_traffic_over_a_100_Mbps_link_instead_of_a_10_Gbps_link\" title=\"Why is OSPF routing traffic over a 100 Mbps link instead of a 10 Gbps link?\">Why is OSPF routing traffic over a 100 Mbps link instead of a 10 Gbps link?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Do_mismatched_reference_bandwidths_break_OSPF_neighbor_adjacencies\" title=\"Do mismatched reference bandwidths break OSPF neighbor adjacencies?\">Do mismatched reference bandwidths break OSPF neighbor adjacencies?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#How_is_OSPF_cost_calculated_on_an_EtherChannel_Port-Channel_or_subinterface\" title=\"How is OSPF cost calculated on an EtherChannel (Port-Channel) or subinterface?\">How is OSPF cost calculated on an EtherChannel (Port-Channel) or subinterface?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Why_didnt_changing_ip_ospf_cost_on_my_interface_change_incoming_traffic_from_my_neighbor\" title=\"Why didn&#8217;t changing ip ospf cost on my interface change incoming traffic from my neighbor?\">Why didn&#8217;t changing ip ospf cost on my interface change incoming traffic from my neighbor?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\/#Why_does_an_OSPF_route_metric_stay_stuck_at_20_even_after_I_change_interface_costs\" title=\"Why does an OSPF route metric stay stuck at 20 even after I change interface costs?\">Why does an OSPF route metric stay stuck at 20 even after I change interface costs?<\/a><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"How_Cisco_Calculates_Default_OSPF_Cost_and_Reference_Bandwidth\"><\/span>How Cisco Calculates Default OSPF Cost and Reference Bandwidth<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Before running verification commands on the CLI, it helps to understand why certain interfaces display identical costs despite having vastly different physical speeds. By default, Cisco IOS and IOS-XE calculate an interface&#8217;s OSPF cost as being inversely proportional to its nominal bandwidth:<\/p>\n<p>$$\\text{OSPF Cost} = \\frac{\\text{Reference Bandwidth}}{\\text{Interface Bandwidth}}$$<\/p>\n<p>In Cisco IOS and IOS-XE, the default <strong>reference bandwidth<\/strong> is <strong>100 Mbps<\/strong> ($10^8\\text{ bps}$ or $100,000\\text{ kbps}$). Because the OSPF metric field in RFC 2328 is an unsigned 16-bit integer ranging from <code>1<\/code> to <code>65535<\/code>, Cisco routers use integer division (truncating decimals rather than rounding up) and enforce a minimum cost floor of <code>1<\/code>. Consequently, any interface operating at 100 Mbps or faster calculates to a value of <code>1<\/code> or less and is assigned a default cost of <code>1<\/code>.<\/p>\n<p>The following comparison table breaks down how Cisco IOS calculates the default OSPF cost across standard physical and logical interface types:<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Interface Type<\/th>\n<th style=\"text-align: left;\">Default Cisco Bandwidth<\/th>\n<th style=\"text-align: left;\">Calculation ($100,000\\text{ kbps} \/ \\text{BW}$)<\/th>\n<th style=\"text-align: left;\">Default OSPF Cost<\/th>\n<th style=\"text-align: left;\">Path Selection Impact<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Loopback<\/strong> (<code>Lo0<\/code>)<\/td>\n<td style=\"text-align: left;\">8,000,000 kbps (8 Gbps)<\/td>\n<td style=\"text-align: left;\">Hardcoded per RFC 2328 stub host rule<\/td>\n<td style=\"text-align: left;\"><strong>1<\/strong><\/td>\n<td style=\"text-align: left;\">Always advertised with a fixed cost of 1 unless manually overridden.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>GRE Tunnel<\/strong> (<code>Tu0<\/code>)<\/td>\n<td style=\"text-align: left;\">100 kbps<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 100$<\/td>\n<td style=\"text-align: left;\"><strong>1000<\/strong><\/td>\n<td style=\"text-align: left;\">Treated as a very slow backup path by default.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Serial (56k)<\/strong><\/td>\n<td style=\"text-align: left;\">56 kbps<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 56 = 1785.71$<\/td>\n<td style=\"text-align: left;\"><strong>1785<\/strong><\/td>\n<td style=\"text-align: left;\">Fractional remainder is truncated via integer division.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Serial (T1)<\/strong> (<code>Se0\/0\/0<\/code>)<\/td>\n<td style=\"text-align: left;\">1,544 kbps (1.544 Mbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 1,544 = 64.76$<\/td>\n<td style=\"text-align: left;\"><strong>64<\/strong><\/td>\n<td style=\"text-align: left;\">Standard legacy WAN cost; fractional value <code>.76<\/code> is dropped.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Serial (E1)<\/strong> (<code>Se0\/0\/1<\/code>)<\/td>\n<td style=\"text-align: left;\">2,048 kbps (2.048 Mbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 2,048 = 48.82$<\/td>\n<td style=\"text-align: left;\"><strong>48<\/strong><\/td>\n<td style=\"text-align: left;\">Slightly preferred over T1 links due to higher nominal bandwidth.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Ethernet<\/strong> (<code>Et0\/0<\/code>)<\/td>\n<td style=\"text-align: left;\">10,000 kbps (10 Mbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 10,000$<\/td>\n<td style=\"text-align: left;\"><strong>10<\/strong><\/td>\n<td style=\"text-align: left;\">Properly penalized compared to 100 Mbps FastEthernet.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>FastEthernet<\/strong> (<code>Fa0\/0<\/code>)<\/td>\n<td style=\"text-align: left;\">100,000 kbps (100 Mbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 100,000$<\/td>\n<td style=\"text-align: left;\"><strong>1<\/strong><\/td>\n<td style=\"text-align: left;\">Matches the default 100 Mbps reference bandwidth ceiling.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>GigabitEthernet<\/strong> (<code>Gi0\/0<\/code>)<\/td>\n<td style=\"text-align: left;\">1,000,000 kbps (1 Gbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 1,000,000 = 0.1$<\/td>\n<td style=\"text-align: left;\"><strong>1<\/strong><\/td>\n<td style=\"text-align: left;\">Sub-1 result rounds up to minimum allowed integer of 1; tied with FastEthernet.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>TenGigabitEthernet<\/strong> (<code>Te0\/0<\/code>)<\/td>\n<td style=\"text-align: left;\">10,000,000 kbps (10 Gbps)<\/td>\n<td style=\"text-align: left;\">$100,000 \/ 10,000,000 = 0.01$<\/td>\n<td style=\"text-align: left;\"><strong>1<\/strong><\/td>\n<td style=\"text-align: left;\">Indistinguishable from 100M and 1G links without reference bandwidth tuning.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>40G \/ 100G Ethernet<\/strong><\/td>\n<td style=\"text-align: left;\">40,000,000+ kbps<\/td>\n<td style=\"text-align: left;\">$&lt; 0.0025$<\/td>\n<td style=\"text-align: left;\"><strong>1<\/strong><\/td>\n<td style=\"text-align: left;\">Requires global reference bandwidth scaling to prevent suboptimal ECMP routing.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Key Takeaway:<\/strong> Without modifying the default 100 Mbps reference bandwidth, a Cisco router cannot differentiate between FastEthernet (100 Mbps), GigabitEthernet (1 Gbps), and 10-GigabitEthernet (10 Gbps) interfaces\u2014assigning all of them a default cost of <code>1<\/code>.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_CLI_Commands_to_Check_OSPF_Interface_and_Route_Cost\"><\/span>Cisco CLI Commands to Check OSPF Interface and Route Cost<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>With the default calculation behavior in mind, you can inspect both <strong>individual interface link costs<\/strong> and <strong>cumulative route metrics<\/strong> directly from privileged EXEC mode. Use the following Cisco IOS CLI templates and sample outputs to locate the exact cost values.<\/p>\n<pre><code class=\"language-ios\">! =====================================================================\n! 1. CHECK ALL OSPF INTERFACE COSTS AT A GLANCE\n! Locate the &quot;Cost&quot; column for the per-link egress OSPF metric.\n! =====================================================================\nRouter# show ip ospf interface brief\nInterface    PID   Area            IP Address\/Mask    Cost  State Nbrs F\/C\nGi0\/0        1     0               10.1.12.1\/30       1     DR    1\/1\nGi0\/1        1     0               10.1.13.1\/30       10    BDR   1\/1\nSe0\/0\/0      1     0               172.16.1.1\/30      64    P2P   1\/1\nLo0          1     0               192.168.1.1\/32     1     LOOP  0\/0\n\n! =====================================================================\n! 2. CHECK DETAILED OSPF COST ON A SPECIFIC INTERFACE\n! Locate &quot;Cost:&quot; at the end of line 2 in the output.\n! =====================================================================\nRouter# show ip ospf interface GigabitEthernet0\/1\nGigabitEthernet0\/1 is up, line protocol is up \n  Internet Address 10.1.13.1\/30, Area 0, Attached via Network Statement\n  Process ID 1, Router ID 192.168.1.1, Network Type BROADCAST, Cost: 10\n  Topology-MTID    Cost    Disabled    Shutdown      Topology Name\n        0           10        no          no            Base\n  Transmit Delay is 1 sec, State BDR, Priority 1\n\n! =====================================================================\n! 3. CHECK CUMULATIVE OSPF ROUTE COST IN THE IP ROUTING TABLE\n! Inside [110\/20]: 110 = Administrative Distance, 20 = Total OSPF Cost.\n! =====================================================================\nRouter# show ip route ospf\n      10.0.0.0\/8 is variably subnetted, 5 subnets, 2 masks\nO        10.2.2.0\/24 [110\/2] via 10.1.12.2, 01:14:22, GigabitEthernet0\/0\nO IA     10.3.3.0\/24 [110\/20] via 10.1.13.2, 00:45:10, GigabitEthernet0\/1\nO E2     172.30.0.0\/16 [110\/20] via 10.1.12.2, 00:12:04, GigabitEthernet0\/0\n\n! =====================================================================\n! 4. CHECK DETAILED PATH METRIC FOR A SINGLE DESTINATION PREFIX\n! Locate &quot;metric &lt;value&gt;&quot; on line 2 and &quot;Route metric is &lt;value&gt;&quot;.\n! =====================================================================\nRouter# show ip route 10.3.3.0\nRouting entry for 10.3.3.0\/24\n  Known via &quot;ospf 1&quot;, distance 110, metric 20, type inter area\n  Last update from 10.1.13.2 on GigabitEthernet0\/1, 00:45:15 ago\n  Routing Descriptor Blocks:\n  * 10.1.13.2, from 192.168.3.3, 00:45:15 ago, via GigabitEthernet0\/1\n      Route metric is 20, traffic share count is 1\n<\/code><\/pre>\n<p><strong>Key Takeaway:<\/strong> Use <code>show ip ospf interface brief<\/code> to verify the local outgoing cost of each individual interface, and use <code>show ip route ospf<\/code> (reading the second number inside the <code>[AD\/Metric]<\/code> brackets) to verify the cumulative end-to-end cost to reach a remote subnet.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_OSPF_Command_Reference_IOS_IOS-XE_and_NX-OS_Syntax\"><\/span>Cisco OSPF Command Reference: IOS, IOS-XE, and NX-OS Syntax<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While the core verification workflow remains consistent across Cisco routing platforms, syntax options, VRF arguments, and default reference bandwidth parameters differ between <strong>Cisco IOS \/ IOS-XE<\/strong> (Catalyst, ISR, ASR) and <strong>Cisco NX-OS<\/strong> (Nexus switches). The following specification details the official command syntax, output field definitions, and platform defaults.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Command_Syntax_Specification\"><\/span>Command Syntax Specification<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Cisco IOS \/ IOS-XE Verification Syntax:<\/strong><br \/>\n  <code>show ip ospf [process-id] interface [brief] [interface-type interface-number]<\/code><br \/>\n  <code>show ip route [vrf vrf-name] ospf [process-id]<\/code><\/li>\n<li><strong>Cisco NX-OS Verification Syntax:<\/strong><br \/>\n  <code>show ip ospf [instance-tag] interface [brief] [interface-type slot\/port] [vrf vrf-name]<\/code><br \/>\n  <code>show ip route [route-prefix] ospf [instance-tag] [vrf vrf-name]<\/code><\/li>\n<li><strong>Cisco IOS \/ IOS-XE Cost Configuration Syntax:<\/strong><br \/>\n  Interface Mode: <code>ip ospf cost &lt;1-65535&gt;<\/code><br \/>\n  Router Mode: <code>auto-cost reference-bandwidth &lt;1-4294967&gt;<\/code> <em>(value specified solely as an integer in Mbps)<\/em><\/li>\n<li><strong>Cisco NX-OS Cost Configuration Syntax:<\/strong><br \/>\n  Interface Mode: <code>ip ospf cost &lt;1-65535&gt;<\/code><br \/>\n  Router Mode: <code>auto-cost reference-bandwidth &lt;number&gt; [Mbps | Gbps]<\/code> <em>(defaults to Mbps if unit keyword is omitted)<\/em><\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Output_Field_Definitions\"><\/span>Output Field Definitions<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong><code>PID<\/code> \/ <code>Process ID<\/code>:<\/strong> The locally significant OSPF process identifier (IOS\/IOS-XE) or instance tag (NX-OS) to which the interface belongs.<\/li>\n<li><strong><code>Cost<\/code>:<\/strong> The unsigned 16-bit integer (<code>1<\/code> to <code>65535<\/code>) representing the link-state metric advertised in Router LSAs (Type 1) for this interface.<\/li>\n<li><strong><code>Topology-MTID Cost<\/code>:<\/strong> Displays Multi-Topology Routing (MTR) specific costs in IOS-XE; <code>MTID 0<\/code> (<code>Base<\/code>) represents the standard IPv4 unicast OSPF topology cost.<\/li>\n<li><strong><code>Distance<\/code>:<\/strong> The Administrative Distance of the routing protocol (<code>110<\/code> by default for OSPF in both IOS-XE and NX-OS).<\/li>\n<li><strong><code>Metric<\/code>:<\/strong> The cumulative sum of outgoing interface costs from the local router to the target network (plus external redistribution costs for <code>E1<\/code>\/<code>E2<\/code> or <code>N1<\/code>\/<code>N2<\/code> routes).<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Platform_Default_Differences_IOSIOS-XE_vs_NX-OS\"><\/span>Platform Default Differences (IOS\/IOS-XE vs. NX-OS)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Parameter<\/th>\n<th style=\"text-align: left;\">Cisco IOS \/ IOS-XE Default<\/th>\n<th style=\"text-align: left;\">Cisco Nexus NX-OS Default<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Default Reference Bandwidth<\/strong><\/td>\n<td style=\"text-align: left;\"><code>100 Mbps<\/code><\/td>\n<td style=\"text-align: left;\"><code>40 Gbps<\/code> (<code>40,000 Mbps<\/code>)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Default 1G Interface Cost<\/strong><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<td style=\"text-align: left;\"><code>40<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Default 10G Interface Cost<\/strong><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<td style=\"text-align: left;\"><code>4<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Default 40G Interface Cost<\/strong><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Loopback Interface Cost<\/strong><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<td style=\"text-align: left;\"><code>1<\/code><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>Reference Documentation: Cisco IOS IP Routing: OSPF Command Reference and Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide.<\/em><\/p>\n<p><strong>Key Takeaway:<\/strong> In mixed data center environments where Cisco IOS-XE routers peer with Cisco Nexus NX-OS switches, you must explicitly align the <code>auto-cost reference-bandwidth<\/code> on both platforms because NX-OS defaults to 40 Gbps while IOS-XE defaults to 100 Mbps.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Change_OSPF_Cost_on_a_Cisco_Router\"><\/span>How to Change OSPF Cost on a Cisco Router<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Once you have checked your current OSPF metrics and identified links that need adjustment, Cisco IOS provides three methods to modify OSPF cost. You can scale costs globally across all interfaces, override the cost on a single interface, or adjust the nominal interface bandwidth.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Scale_Costs_Globally_Using_auto-cost_reference-bandwidth_Recommended_Baseline\"><\/span>Step 1: Scale Costs Globally Using <code>auto-cost reference-bandwidth<\/code> (Recommended Baseline)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To allow OSPF to automatically distinguish between FastEthernet, 1G, 10G, 40G, and 100G interfaces using the calculation formula covered earlier, increase the global reference bandwidth under the OSPF routing process. Set this value at least as high as the fastest link in your network (in Mbps), and configure the exact same value on <strong>every router<\/strong> in the OSPF domain.<\/p>\n<pre><code class=\"language-ios\">Router# configure terminal\nRouter(config)# router ospf 1\n! Set reference bandwidth to 100,000 Mbps (100 Gbps)\nRouter(config-router)# auto-cost reference-bandwidth 100000\n% OSPF: Reference bandwidth is changed. \n        Please ensure reference bandwidth is consistent across all routers.\nRouter(config-router)# end\n<\/code><\/pre>\n<p>With a <code>100000<\/code> Mbps (100 Gbps) reference bandwidth applied, Cisco IOS automatically recalculates default interface costs as follows:<br \/>\n* <strong>100 Gbps interface:<\/strong> Cost = <code>1<\/code><br \/>\n* <strong>40 Gbps interface:<\/strong> Cost = <code>2<\/code><br \/>\n* <strong>10 Gbps interface:<\/strong> Cost = <code>10<\/code><br \/>\n* <strong>1 Gbps interface:<\/strong> Cost = <code>100<\/code><br \/>\n* <strong>100 Mbps interface:<\/strong> Cost = <code>1000<\/code><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Override_Cost_on_a_Specific_Interface_Using_ip_ospf_cost_For_Traffic_Engineering\"><\/span>Step 2: Override Cost on a Specific Interface Using <code>ip ospf cost<\/code> (For Traffic Engineering)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When you need to steer traffic away from a specific link (such as a high-latency satellite circuit or a backup WAN connection) without changing the global formula, manually assign a cost between <code>1<\/code> and <code>65535<\/code> directly on the interface. An explicit <code>ip ospf cost<\/code> command always takes precedence over both <code>auto-cost reference-bandwidth<\/code> and the interface <code>bandwidth<\/code> setting.<\/p>\n<pre><code class=\"language-ios\">Router# configure terminal\nRouter(config)# interface GigabitEthernet0\/1\n! Manually set the OSPF link cost to 500\nRouter(config-if)# ip ospf cost 500\nRouter(config-if)# end\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Adjust_Nominal_Interface_Bandwidth_Using_bandwidth_Use_with_Caution\"><\/span>Step 3: Adjust Nominal Interface Bandwidth Using <code>bandwidth<\/code> (Use with Caution)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If a physical GigabitEthernet port is connected to an ISP circuit throttled to a lower sub-rate speed (for example, a 50 Mbps Metro Ethernet handoff), you can configure the informational <code>bandwidth<\/code> command in kilobits per second (kbps). OSPF will dynamically recalculate the link cost based on this new bandwidth value\u2014provided <code>ip ospf cost<\/code> is not configured on the interface.<\/p>\n<pre><code class=\"language-ios\">Router# configure terminal\nRouter(config)# interface GigabitEthernet0\/2\n! Specify 50 Mbps in kilobits per second (50,000 kbps)\nRouter(config-if)# bandwidth 50000\nRouter(config-if)# end\n<\/code><\/pre>\n<p><em>Note:<\/em> Avoid using the <code>bandwidth<\/code> command solely to manipulate OSPF routing if other features rely on the interface speed. Changing the interface <code>bandwidth<\/code> parameter also alters EIGRP composite metric calculations, QoS policy bandwidth percentages, and SNMP <code>ifSpeed<\/code> reporting. Prefer <code>ip ospf cost<\/code> whenever your goal is strictly OSPF path manipulation.<\/p>\n<p><strong>Key Takeaway:<\/strong> Use <code>auto-cost reference-bandwidth<\/code> across all routers to establish an accurate baseline for high-speed interfaces, and use per-interface <code>ip ospf cost<\/code> whenever you need surgical traffic engineering overrides.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_OSPF_Cost_and_Verification_CLI_Cheat_Sheet\"><\/span>Cisco OSPF Cost and Verification CLI Cheat Sheet<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Bookmark or copy this consolidated list of Cisco CLI commands for daily network administration, change validation, and CCNA\/CCNP lab troubleshooting:<\/p>\n<ol>\n<li><strong><code>show ip ospf interface brief<\/code><\/strong> \u2014 Displays a compact table of every OSPF-enabled interface, its area assignment, IP address, and current link <code>Cost<\/code>.<\/li>\n<li><strong><code>show ip ospf interface &lt;interface&gt; | include Cost<\/code><\/strong> \u2014 Filters detailed interface output to immediately return the process ID, network type, and exact link cost on a single line.<\/li>\n<li><strong><code>show ip route ospf<\/code><\/strong> \u2014 Lists all OSPF-learned prefixes in the global routing table along with their <code>[Administrative Distance \/ Cumulative Cost]<\/code> values.<\/li>\n<li><strong><code>show ip ospf border-routers<\/code><\/strong> \u2014 Displays the internal OSPF path cost required to reach Area Border Routers (ABRs) and Autonomous System Boundary Routers (ASBRs)\u2014critical for diagnosing tie-breakers on External Type 2 (<code>O E2<\/code>) routes.<\/li>\n<li><strong><code>show ip ospf database router self-originate<\/code><\/strong> \u2014 Inspects the local router&#8217;s Type 1 Router LSA to verify the exact <code>TOS 0 Metrics<\/code> (link costs) being advertised to OSPF neighbors.<\/li>\n<li><strong><code>show running-config | section router ospf<\/code><\/strong> \u2014 Checks the active OSPF process configuration to verify whether a custom <code>auto-cost reference-bandwidth<\/code> has been applied.<\/li>\n<li><strong><code>show interfaces &lt;interface&gt; | include BW<\/code><\/strong> \u2014 Displays the nominal hardware or configured bandwidth (<code>BW<\/code> in Kbit\/sec) that OSPF uses as the denominator in its cost formula.<\/li>\n<li><strong><code>ip ospf cost &lt;1-65535&gt;<\/code><\/strong> \u2014 Interface configuration command that hardcodes the outgoing OSPF link metric, bypassing bandwidth-based calculations.<\/li>\n<li><strong><code>auto-cost reference-bandwidth &lt;mbps&gt;<\/code><\/strong> \u2014 Router OSPF configuration command that changes the numerator in the default cost formula from 100 Mbps to a user-defined value.<\/li>\n<\/ol>\n<p><strong>Key Takeaway:<\/strong> Combining <code>show ip ospf interface brief<\/code> with <code>show ip ospf database router self-originate<\/code> and <code>show ip route ospf<\/code> lets you trace OSPF metrics across all three stages: local interface calculation, LSA advertisement, and final RIB installation.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Troubleshooting_Unexpected_OSPF_Path_Costs_and_Suboptimal_Routing\"><\/span>Troubleshooting Unexpected OSPF Path Costs and Suboptimal Routing<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Even when interfaces are up and neighbors reach the <code>FULL<\/code> state, OSPF can occasionally select a slower path or display an unexpected metric in the routing table. The following FAQ addresses the most common real-world edge cases.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_is_OSPF_routing_traffic_over_a_100_Mbps_link_instead_of_a_10_Gbps_link\"><\/span>Why is OSPF routing traffic over a 100 Mbps link instead of a 10 Gbps link?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If the router is still using the default 100 Mbps reference bandwidth, both the 100 Mbps link and the 10 Gbps link calculate to a cost of <code>1<\/code>. Because OSPF sees identical link costs, it treats a single-hop 100 Mbps path as equal to a single-hop 10 Gbps path (performing equal-cost multi-path load balancing across both) or even prefers a single-hop 100 Mbps link (total cost <code>1<\/code>) over a two-hop 10 Gbps path (total cost <code>2<\/code>). Configure <code>auto-cost reference-bandwidth<\/code> across all routers to resolve this.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Do_mismatched_reference_bandwidths_break_OSPF_neighbor_adjacencies\"><\/span>Do mismatched reference bandwidths break OSPF neighbor adjacencies?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. Reference bandwidth is a locally significant calculation parameter and is not exchanged inside OSPF Hello packets, so neighbors will still form <code>FULL<\/code> adjacencies. However, mismatched reference bandwidths cause routers in the same area to advertise vastly different cost scales in their LSAs, leading to asymmetric routing, suboptimal path selection, and unexpected ECMP behavior.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"How_is_OSPF_cost_calculated_on_an_EtherChannel_Port-Channel_or_subinterface\"><\/span>How is OSPF cost calculated on an EtherChannel (Port-Channel) or subinterface?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On a logical <code>Port-channel<\/code> interface, Cisco IOS dynamically calculates the interface bandwidth as the <strong>sum of all active physical member links<\/strong>. For example, four bundled 1 Gbps interfaces yield an aggregate Port-Channel bandwidth of <code>4,000,000 kbps<\/code> (4 Gbps). If the reference bandwidth is set high enough (such as <code>10000<\/code> Mbps or <code>40000<\/code> Mbps) and no manual <code>ip ospf cost<\/code> is configured on the Port-Channel, OSPF automatically assigns a lower cost to the bundle and dynamically increases the cost if a member link fails. On 802.1Q subinterfaces (such as <code>GigabitEthernet0\/0.10<\/code>), each subinterface inherits the full nominal bandwidth of the parent physical interface unless manually modified.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_didnt_changing_ip_ospf_cost_on_my_interface_change_incoming_traffic_from_my_neighbor\"><\/span>Why didn&#8217;t changing <code>ip ospf cost<\/code> on my interface change incoming traffic from my neighbor?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>OSPF calculates the shortest path tree by summing <strong>outgoing (egress)<\/strong> interface costs along the route from the calculating router to the destination. Increasing <code>ip ospf cost<\/code> on Router A&#8217;s interface only increases the metric for traffic <em>leaving<\/em> Router A via that link. Router B computes its path toward Router A using Router B&#8217;s own outgoing interface cost. To influence how upstream neighbors route traffic back to your router, you must adjust <code>ip ospf cost<\/code> on the neighbor&#8217;s egress interface.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_does_an_OSPF_route_metric_stay_stuck_at_20_even_after_I_change_interface_costs\"><\/span>Why does an OSPF route metric stay stuck at 20 even after I change interface costs?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Examine the route code in <code>show ip route ospf<\/code>. If the route is marked <code>O E2<\/code> (OSPF External Type 2) or <code>O N2<\/code> (NSSA External Type 2), it only displays the external redistribution seed metric (which defaults to <code>20<\/code>) in the routing table and ignores internal OSPF link costs in that displayed number. Internally, the router still checks the cumulative internal cost to reach the ASBR (visible via <code>show ip ospf border-routers<\/code>) to break ties between multiple paths. If you want the routing table metric to reflect the sum of the external cost plus all internal link costs, change the redistribution command on the ASBR to use <code>metric-type 1<\/code> (<code>O E1<\/code>).<\/p>\n<p><strong>Key Takeaway:<\/strong> When troubleshooting unexpected OSPF metrics, always verify whether the route is an External Type 2 (<code>O E2<\/code>) prefix, confirm that <code>auto-cost reference-bandwidth<\/code> matches across every router, and remember that OSPF only evaluates outgoing interface costs along a path.<\/p>\n<hr \/>\n<p>Accurately checking and managing OSPF cost on a Cisco router comes down to distinguishing between per-link egress costs (<code>show ip ospf interface brief<\/code>) and cumulative path metrics (<code>show ip route ospf<\/code>). By auditing your interface metrics, aligning your reference bandwidth across IOS-XE and NX-OS platforms, and applying targeted <code>ip ospf cost<\/code> overrides where needed, you ensure OSPF consistently forwards traffic over your highest-capacity network paths.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-ospf-cost-on-cisco-router_24593.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+OSPF+Cost+on+Cisco+Router+https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\",\"How to Check OSPF Cost on Cisco Router\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Open Shortest Path First (OSPF) determines the best path through a network by evaluating a single metric: cost. On a Cisco router, every OSPF-enabled interface is assigned an individual link cost based on its bandwidth, and the router sums these outgoing link costs along a path to compute the cumulative metric installed in the IP&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check OSPF Cost on Cisco Router - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check OSPF Cost on Cisco Router - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Open Shortest Path First (OSPF) determines the best path through a network by evaluating a single metric: cost. On a Cisco router, every OSPF-enabled interface is assigned an individual link cost based on its bandwidth, and the router sums these outgoing link costs along a path to compute the cumulative metric installed in the IP... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T09:06:38+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"12 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\",\"name\":\"How to Check OSPF Cost on Cisco Router - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T09:06:38+00:00\",\"dateModified\":\"2026-11-17T09:06:38+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check OSPF Cost on Cisco Router\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check OSPF Cost on Cisco Router\",\"datePublished\":\"2026-11-17T09:06:38+00:00\",\"dateModified\":\"2026-11-17T09:06:38+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage\"},\"wordCount\":1960,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check OSPF Cost on Cisco Router - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html","og_locale":"en_US","og_type":"article","og_title":"How to Check OSPF Cost on Cisco Router - SPOTO Official Blog","og_description":"Open Shortest Path First (OSPF) determines the best path through a network by evaluating a single metric: cost. On a Cisco router, every OSPF-enabled interface is assigned an individual link cost based on its bandwidth, and the router sums these outgoing link costs along a path to compute the cumulative metric installed in the IP... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T09:06:38+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"12 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html","name":"How to Check OSPF Cost on Cisco Router - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T09:06:38+00:00","dateModified":"2026-11-17T09:06:38+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check OSPF Cost on Cisco Router"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check OSPF Cost on Cisco Router","datePublished":"2026-11-17T09:06:38+00:00","dateModified":"2026-11-17T09:06:38+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#webpage"},"wordCount":1960,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-ospf-cost-on-cisco-router_24593.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24593"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24593"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24593\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24593"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24593"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24593"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}