{"id":24585,"date":"2026-11-17T15:40:16","date_gmt":"2026-11-17T07:40:16","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html"},"modified":"2026-11-17T15:40:16","modified_gmt":"2026-11-17T07:40:16","slug":"how-to-check-latency-in-cisco-router","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html","title":{"rendered":"How to Check Latency in Cisco Router"},"content":{"rendered":"<p>Measuring network latency directly from a Cisco router allows network engineers to isolate WAN slowdowns, verify service provider SLAs, and distinguish between transit link congestion and local device bottlenecks. Whether you need an immediate round-trip time (RTT) measurement between two endpoints or continuous telemetry tracking microsecond jitter across voice and video paths, Cisco IOS and IOS-XE provide built-in diagnostic tools for every stage of analysis.<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Checking_Real-Time_Latency_via_Cisco_CLI_Commands\" title=\"Checking Real-Time Latency via Cisco CLI Commands\">Checking Real-Time Latency via Cisco CLI Commands<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_1_Run_a_Standard_ICMP_Ping_for_Quick_RTT_Baseline\" title=\"Step 1: Run a Standard ICMP Ping for Quick RTT Baseline\">Step 1: Run a Standard ICMP Ping for Quick RTT Baseline<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_2_Use_Extended_Ping_to_Test_Specific_Paths_and_Payloads\" title=\"Step 2: Use Extended Ping to Test Specific Paths and Payloads\">Step 2: Use Extended Ping to Test Specific Paths and Payloads<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_3_Isolate_Hop-by-Hop_Latency_with_Traceroute\" title=\"Step 3: Isolate Hop-by-Hop Latency with Traceroute\">Step 3: Isolate Hop-by-Hop Latency with Traceroute<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Understanding_show_interfaces_Delay_DLY_vs_Actual_Network_Latency\" title=\"Understanding show interfaces Delay (DLY) vs. Actual Network Latency\">Understanding show interfaces Delay (DLY) vs. Actual Network Latency<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Does_show_interfaces_display_real-time_network_latency_in_Cisco_IOS\" title=\"Does show interfaces display real-time network latency in Cisco IOS?\">Does show interfaces display real-time network latency in Cisco IOS?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#What_does_the_DLY_metric_in_show_interfaces_actually_represent\" title=\"What does the DLY metric in show interfaces actually represent?\">What does the DLY metric in show interfaces actually represent?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Does_changing_the_delay_command_on_an_interface_affect_actual_packet_latency\" title=\"Does changing the delay command on an interface affect actual packet latency?\">Does changing the delay command on an interface affect actual packet latency?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Configuring_Cisco_IP_SLA_for_Continuous_Latency_and_Jitter_Monitoring\" title=\"Configuring Cisco IP SLA for Continuous Latency and Jitter Monitoring\">Configuring Cisco IP SLA for Continuous Latency and Jitter Monitoring<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Template_1_ICMP_Echo_Operation_Continuous_RTT_Latency_Tracking\" title=\"Template 1: ICMP Echo Operation (Continuous RTT Latency Tracking)\">Template 1: ICMP Echo Operation (Continuous RTT Latency Tracking)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Template_2_UDP_Jitter_Operation_RTT_One-Way_Latency_Jitter_and_Packet_Loss\" title=\"Template 2: UDP Jitter Operation (RTT, One-Way Latency, Jitter, and Packet Loss)\">Template 2: UDP Jitter Operation (RTT, One-Way Latency, Jitter, and Packet Loss)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#CLI_Commands_to_View_IP_SLA_Latency_Statistics\" title=\"CLI Commands to View IP SLA Latency Statistics\">CLI Commands to View IP SLA Latency Statistics<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#How_to_Troubleshoot_High_Latency_and_Packet_Loss_on_a_Cisco_Router\" title=\"How to Troubleshoot High Latency and Packet Loss on a Cisco Router\">How to Troubleshoot High Latency and Packet Loss on a Cisco Router<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_1_Differentiate_Control-Plane_Latency_from_Transit_Data-Plane_Latency\" title=\"Step 1: Differentiate Control-Plane Latency from Transit Data-Plane Latency\">Step 1: Differentiate Control-Plane Latency from Transit Data-Plane Latency<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_2_Check_for_Physical_Layer_Errors_and_Duplex_Mismatches\" title=\"Step 2: Check for Physical Layer Errors and Duplex Mismatches\">Step 2: Check for Physical Layer Errors and Duplex Mismatches<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_3_Diagnose_Interface_Output_Queue_Drops_and_Buffer_Congestion\" title=\"Step 3: Diagnose Interface Output Queue Drops and Buffer Congestion\">Step 3: Diagnose Interface Output Queue Drops and Buffer Congestion<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Step_4_Audit_Active_QoS_Shaping_and_Policing_Policies\" title=\"Step 4: Audit Active QoS Shaping and Policing Policies\">Step 4: Audit Active QoS Shaping and Policing Policies<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Best_Network_Monitoring_Tools_for_Cisco_Router_Latency_and_IP_SLA\" title=\"Best Network Monitoring Tools for Cisco Router Latency and IP SLA\">Best Network Monitoring Tools for Cisco Router Latency and IP SLA<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Official_Cisco_IOS_Command_References_and_Documentation\" title=\"Official Cisco IOS Command References and Documentation\">Official Cisco IOS Command References and Documentation<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Checking_Real-Time_Latency_via_Cisco_CLI_Commands\"><\/span>Checking Real-Time Latency via Cisco CLI Commands<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When you need an immediate, ad-hoc measurement of round-trip time (RTT) from a Cisco router to a remote host or next-hop gateway, the command-line interface (CLI) offers three sequential diagnostic steps.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Run_a_Standard_ICMP_Ping_for_Quick_RTT_Baseline\"><\/span>Step 1: Run a Standard ICMP Ping for Quick RTT Baseline<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>From user EXEC (<code>&gt;<\/code>) or privileged EXEC (<code>#<\/code>) mode, run the standard <code>ping<\/code> command to send five 100-byte ICMP Echo Request packets to the target IP address:<\/p>\n<pre><code class=\"language-ios\">Router# ping 8.8.8.8\nType escape sequence to abort.\nSending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:\n!!!!!\nSuccess rate is 100 percent (5\/5), round-trip min\/avg\/max = 12\/14\/18 ms\n<\/code><\/pre>\n<p>Evaluate the output using two indicators:<br \/>\n* <strong>Response Characters:<\/strong> Each <code>!<\/code> indicates a successful reply received within the 2-second timeout. A <code>.<\/code> indicates a timeout (packet loss), while <code>U<\/code> denotes that an ICMP Destination Unreachable message was returned.<br \/>\n* <strong>RTT Summary (<code>min\/avg\/max<\/code>):<\/strong> Displayed at the bottom in milliseconds (<code>ms<\/code>), showing the fastest, average, and slowest round-trip times across the sample.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Use_Extended_Ping_to_Test_Specific_Paths_and_Payloads\"><\/span>Step 2: Use Extended Ping to Test Specific Paths and Payloads<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>A standard ping uses the outbound interface IP chosen by the routing table and sends only five small packets, which often misses intermittent latency spikes or MTU-related delays. Run an extended ping in privileged EXEC mode either interactively (by typing <code>ping<\/code> and pressing <strong>Enter<\/strong>) or via a single inline command:<\/p>\n<pre><code class=\"language-ios\">Router# ping 10.20.30.1 source GigabitEthernet0\/0\/1 repeat 100 size 1400 df-bit\n<\/code><\/pre>\n<ul>\n<li><strong><code>source &lt;interface | ip&gt;<\/code>:<\/strong> Forces the router to originate probes from a specific LAN or tunnel interface, verifying latency across policy-routed paths or IPsec VPNs.<\/li>\n<li><strong><code>repeat &lt;count&gt;<\/code>:<\/strong> Increases the sample size (for example, <code>100<\/code> or <code>500<\/code> packets) to expose periodic latency jitter that a 5-packet test misses.<\/li>\n<li><strong><code>size &lt;bytes&gt;<\/code> and <code>df-bit<\/code>:<\/strong> Tests whether larger packets trigger serialization delays or fragmentation issues along the path. If the destination resides inside a specific VRF, insert <code>vrf &lt;vrf-name&gt;<\/code> immediately after <code>ping<\/code>.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Isolate_Hop-by-Hop_Latency_with_Traceroute\"><\/span>Step 3: Isolate Hop-by-Hop Latency with Traceroute<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If <code>ping<\/code> reveals elevated end-to-end RTT, use <code>traceroute<\/code> to identify exactly which intermediate router or carrier link introduces the delay:<\/p>\n<pre><code class=\"language-ios\">Router# traceroute 10.20.30.1 source GigabitEthernet0\/0\/1 numeric\nType escape sequence to abort.\nTracing the route to 10.20.30.1\nVRF info: (vrf in name\/id, vrf out name\/id)\n  1 192.168.1.2 1 msec 1 msec 1 msec\n  2 172.16.10.1 4 msec 3 msec 4 msec\n  3 10.20.30.1 48 msec 47 msec 49 msec\n<\/code><\/pre>\n<p>Cisco IOS <code>traceroute<\/code> transmits three UDP probes per hop with incrementing Time-to-Live (TTL) values and prints the RTT in <code>msec<\/code> for each probe. Including the <code>numeric<\/code> keyword skips reverse DNS lookups on each hop, ensuring the CLI outputs probe results immediately without DNS timeout delays. Looking for a sudden, sustained jump in RTT from one hop to the next pinpoints the exact segment responsible for the latency increase.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Understanding_show_interfaces_Delay_DLY_vs_Actual_Network_Latency\"><\/span>Understanding <code>show interfaces<\/code> Delay (DLY) vs. Actual Network Latency<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>After running CLI ping tests, administrators frequently inspect interface counters using <code>show interfaces<\/code> and notice a <code>DLY<\/code> metric in the output. Because this value is often confused with live link latency, it is important to clarify how Cisco IOS treats interface delay parameters.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Does_show_interfaces_display_real-time_network_latency_in_Cisco_IOS\"><\/span>Does <code>show interfaces<\/code> display real-time network latency in Cisco IOS?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>No. When you execute <code>show interfaces &lt;interface&gt;<\/code>, the <code>DLY<\/code> value shown on the third line (for example, <code>MTU 1500 bytes, BW 1000000 Kbit\/sec, DLY 10 usec<\/code>) is a static, hardcoded constant measured in microseconds (<code>usec<\/code>). It never fluctuates based on live traffic load, physical propagation time, or queuing delay.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"What_does_the_DLY_metric_in_show_interfaces_actually_represent\"><\/span>What does the <code>DLY<\/code> metric in <code>show interfaces<\/code> actually represent?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The <code>DLY<\/code> field represents a default theoretical media delay assigned according to the interface type and bandwidth\u2014such as <code>10 usec<\/code> for GigabitEthernet, <code>100 usec<\/code> for FastEthernet, and <code>20000 usec<\/code> for a Serial T1 link. Its purpose in Cisco IOS is to serve as a routing metric component for EIGRP (Enhanced Interior Gateway Routing Protocol), which calculates composite path costs using the cumulative interface delay along a route alongside minimum bandwidth.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Does_changing_the_delay_command_on_an_interface_affect_actual_packet_latency\"><\/span>Does changing the <code>delay<\/code> command on an interface affect actual packet latency?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Not directly on that physical link. Modifying the parameter with the interface subcommand <code>delay &lt;tens-of-microseconds&gt;<\/code> does not alter hardware serialization speed or physical link latency. However, changing the delay value alters EIGRP metric calculations, which can shift traffic onto an alternate network path that has different real-world latency characteristics.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Configuring_Cisco_IP_SLA_for_Continuous_Latency_and_Jitter_Monitoring\"><\/span>Configuring Cisco IP SLA for Continuous Latency and Jitter Monitoring<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While ad-hoc <code>ping<\/code> and <code>traceroute<\/code> commands measure latency at a single moment, tracking trends over time requires automated probing. You can configure Cisco IP SLA directly on the router using the templates below to continuously measure round-trip latency, one-way delay, and jitter.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Template_1_ICMP_Echo_Operation_Continuous_RTT_Latency_Tracking\"><\/span>Template 1: ICMP Echo Operation (Continuous RTT Latency Tracking)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Use this template to monitor round-trip latency to any IP target (even non-Cisco devices or public DNS resolvers) without requiring special software on the destination host:<\/p>\n<pre><code class=\"language-ios\">configure terminal\n! Define IP SLA operation 10\nip sla 10\n icmp-echo &lt;DESTINATION_IP&gt; source-ip &lt;SOURCE_IP_OR_INTERFACE&gt;\n frequency &lt;INTERVAL_IN_SECONDS_E.G._60&gt;\n timeout 5000\n threshold &lt;RTT_ALERT_THRESHOLD_MS_E.G._100&gt;\n history hours-of-statistics-kept 24\n history distributions-of-statistics-kept 5\nexit\n! Schedule operation 10 to run continuously starting immediately\nip sla schedule 10 life forever start-time now\nend\nwrite memory\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Template_2_UDP_Jitter_Operation_RTT_One-Way_Latency_Jitter_and_Packet_Loss\"><\/span>Template 2: UDP Jitter Operation (RTT, One-Way Latency, Jitter, and Packet Loss)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Use this template when monitoring VoIP or real-time video links. It requires enabling <code>ip sla responder<\/code> on the remote Cisco router so both endpoints can timestamp packets for one-way latency and positive\/negative jitter calculations:<\/p>\n<pre><code class=\"language-ios\">! --- Run on Destination (Responder) Cisco Router ---\nconfigure terminal\nip sla responder\nend\n\n! --- Run on Source Cisco Router ---\nconfigure terminal\nip sla 20\n udp-jitter &lt;RESPONDER_IP&gt; &lt;UDP_PORT_E.G._16384&gt; source-ip &lt;SOURCE_IP&gt; num-packets 20 interval 20\n tos 184\n frequency 30\n threshold 150\nexit\nip sla schedule 20 life forever start-time now\nend\nwrite memory\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"CLI_Commands_to_View_IP_SLA_Latency_Statistics\"><\/span>CLI Commands to View IP SLA Latency Statistics<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run the following privileged EXEC commands to inspect the latest RTT completion time, min\/avg\/max jitter, and historical buckets:<\/p>\n<pre><code class=\"language-ios\">! View latest RTT result and return code for ICMP Echo probe\nshow ip sla statistics 10\n\n! View detailed jitter, one-way latency, and packet loss metrics\nshow ip sla statistics 20 details\n\n! View historical latency tables collected over time\nshow ip sla history 10\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Troubleshoot_High_Latency_and_Packet_Loss_on_a_Cisco_Router\"><\/span>How to Troubleshoot High Latency and Packet Loss on a Cisco Router<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When your CLI tests or IP SLA probes confirm high latency or packet drops across a Cisco router, follow this four-step diagnostic sequence to isolate whether the bottleneck is caused by the control plane, physical layer errors, interface congestion, or QoS policies.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Differentiate_Control-Plane_Latency_from_Transit_Data-Plane_Latency\"><\/span>Step 1: Differentiate Control-Plane Latency from Transit Data-Plane Latency<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Pings sent <em>to<\/em> one of the router&#8217;s own IP addresses are punted to the control-plane CPU and may be rate-limited by Control Plane Policing (CoPP), whereas traffic passing <em>through<\/em> the router is forwarded in hardware via Cisco Express Forwarding (CEF). Check whether high CPU utilization is delaying control-plane responses or software-switched packets:<\/p>\n<pre><code class=\"language-ios\">Router# show processes cpu sorted 5sec\nCPU utilization for five seconds: 84%\/12%; one minute: 79%; five minutes: 75%\n PID Runtime(ms)     Invoked      uSecs   5Sec   1Min   5Min TTY Process\n  89     4829100    12049102        400 42.15% 38.40% 36.12%   0 IP Input\n<\/code><\/pre>\n<p>On Cisco IOS-XE platforms (such as ASR 1000, ISR 4000, and Catalyst 8000 Series), also check data-plane Quantum Flow Processor (QFP) load using <code>show platform hardware qfp active datapath utilization<\/code> to verify that hardware forwarding engines are not saturated.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_for_Physical_Layer_Errors_and_Duplex_Mismatches\"><\/span>Step 2: Check for Physical Layer Errors and Duplex Mismatches<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Damaged cables, failing optics, or speed\/duplex mismatches force layer-2 frames to be dropped and retransmitted by upper-layer protocols, manifesting as erratic latency spikes. Inspect the error counters on the ingress and egress interfaces:<\/p>\n<pre><code class=\"language-ios\">Router# show interfaces GigabitEthernet0\/0\/0 | include duplex|errors|CRC|drops\n  Full-duplex, 1000Mb\/s, link type is auto, media type is RJ45\n  0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored\n  Input queue: 0\/375\/0\/0 (size\/max\/drops\/flushes); Total output drops: 14820\n<\/code><\/pre>\n<p>If <code>input errors<\/code>, <code>CRC<\/code>, <code>frame<\/code>, or <code>runts<\/code> are incrementing, resolve the physical cabling, SFP transceiver, or duplex mismatch before investigating higher-layer configurations.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Diagnose_Interface_Output_Queue_Drops_and_Buffer_Congestion\"><\/span>Step 3: Diagnose Interface Output Queue Drops and Buffer Congestion<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Notice the <code>Total output drops<\/code> counter in the <code>show interfaces<\/code> output above. When bursty traffic exceeds the egress bandwidth of a WAN link, packets wait in the interface output buffer\u2014directly increasing queuing latency (bufferbloat)\u2014until the queue fills and tail drops occur. On Cisco IOS-XE routers, inspect the exact hardware drop causes across the forwarding plane:<\/p>\n<pre><code class=\"language-ios\">Router# show platform hardware qfp active statistics drop\n-------------------------------------------------------------------------\nGlobal Drop Stats                         Packets                  Octets\n-------------------------------------------------------------------------\nTailDrop                                    14820                19414200\nipPolicerDrop                                3410                 4126100\n<\/code><\/pre>\n<p>High <code>TailDrop<\/code> counts confirm that egress bandwidth saturation is delaying and dropping packets during traffic bursts.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Audit_Active_QoS_Shaping_and_Policing_Policies\"><\/span>Step 4: Audit Active QoS Shaping and Policing Policies<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Traffic shapers hold excess packets in memory queues to smooth out bursts to a committed information rate (CIR), intentionally trading higher latency for fewer carrier drops. Conversely, policers immediately drop or remark excess traffic. Inspect active Quality of Service (QoS) policies on the egress interface:<\/p>\n<pre><code class=\"language-ios\">Router# show policy-map interface GigabitEthernet0\/0\/0\n<\/code><\/pre>\n<p>Check each traffic class for <code>queue limit<\/code>, <code>(pkts output\/bytes output)<\/code>, <code>(depth\/total drops\/no-buffer drops)<\/code>, and policer <code>exceeded<\/code> or <code>violated<\/code> counters. If latency spikes correlate with rising queue depth inside a shaped class, increase the shaped bandwidth rate (if the WAN circuit allows it) or prioritize latency-sensitive traffic using a Low Latency Queuing (<code>priority<\/code>) class.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Best_Network_Monitoring_Tools_for_Cisco_Router_Latency_and_IP_SLA\"><\/span>Best Network Monitoring Tools for Cisco Router Latency and IP SLA<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While CLI commands are essential for live troubleshooting, enterprise networks rely on external Network Performance Monitoring (NPM) software to poll Cisco routers via SNMP, NetFlow, and IP SLA MIBs for long-term visualization and alerting:<\/p>\n<ol>\n<li><strong>SolarWinds Network Performance Monitor (NPM) &amp; VoIP and Network Quality Manager (VNQM):<\/strong> Polls Cisco routers via SNMP to graph baseline ICMP response time, visualizes hop-by-hop internet latency using NetPath, and integrates directly with Cisco IP SLA (<code>CISCO-RTTMON-MIB<\/code>) to automate WAN jitter, latency, and MOS score alerting.<\/li>\n<li><strong>Paessler PRTG Network Monitor:<\/strong> Includes dedicated <code>Cisco IP SLA<\/code> SNMP sensors alongside high-frequency Ping and System Health sensors, allowing administrators to plot one-way latency, jitter, and packet loss per SLA operation ID on real-time dashboards.<\/li>\n<li><strong>Cisco Catalyst Center &amp; Cisco ThousandEyes:<\/strong> Combines native IOS-XE streaming telemetry with active synthetic monitoring. Supported Cisco ISR 4000, ASR 1000, and Catalyst 8000 Series routers can host embedded ThousandEyes Enterprise Agents directly in a container on the router to visualize end-to-end BGP, WAN, and SaaS application latency.<\/li>\n<li><strong>ManageEngine OpManager:<\/strong> Automatically discovers pre-configured IP SLA probes on Cisco routers via SNMP and generates historical WAN RTT trend reports, threshold violation alerts, and voice quality monitors without manual OID mapping.<\/li>\n<li><strong>Zabbix and LibreNMS (Open-Source Platforms):<\/strong> Free, self-hosted monitoring platforms that ship with built-in Cisco IOS\/IOS-XE discovery templates. Both automatically index <code>CISCO-RTTMON-MIB<\/code> operations and correlate RTT latency spikes with router CPU utilization and interface queue drops on unified graphs.<\/li>\n<\/ol>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Official_Cisco_IOS_Command_References_and_Documentation\"><\/span>Official Cisco IOS Command References and Documentation<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>For syntax specifications, platform-specific release constraints, and SNMP schema definitions across Cisco IOS (15.x) and Cisco IOS-XE (16.x \/ 17.x), consult the following authoritative Cisco documentation resources:<\/p>\n<ul>\n<li><strong>Cisco IOS IP SLAs Configuration Guide:<\/strong> Defines the architecture and step-by-step configuration procedures for <code>icmp-echo<\/code>, <code>udp-jitter<\/code>, <code>icmp-jitter<\/code>, and <code>tcp-connect<\/code> operations, IP SLA responder setup, proactive threshold monitoring (<code>ip sla reaction-configuration<\/code>), and Enhanced Object Tracking integration (<code>track &lt;object-number&gt; ip sla &lt;operation-number&gt;<\/code>).<\/li>\n<li><strong>Cisco IOS IP SLAs Command Reference:<\/strong> Provides the complete alphabetical command syntax, parameter ranges, default values, and command mode hierarchies for all <code>ip sla<\/code> configuration commands and <code>show ip sla<\/code> diagnostic commands.<\/li>\n<li><strong>Cisco IOS Configuration Fundamentals Command Reference (<code>ping<\/code> and <code>traceroute<\/code>):<\/strong> Documents standard and extended EXEC command flags, VRF-aware syntax (<code>ping vrf<\/code>, <code>traceroute vrf<\/code>), protocol-specific options, and complete tables of CLI response status characters (<code>!<\/code>, <code>.<\/code>, <code>U<\/code>, <code>Q<\/code>, <code>M<\/code>, <code>?<\/code>, <code>&amp;<\/code>).<\/li>\n<li><strong>Cisco SNMP Object Navigator (<code>CISCO-RTTMON-MIB<\/code>):<\/strong> Details the official ASN.1 MIB structure (OID <code>1.3.6.1.4.1.9.9.42<\/code>) used to query <code>rttMonLatestRttOperCompletionTime<\/code>, <code>rttMonLatestJitterOperAvgJitter<\/code>, and operation return codes from external SNMP managers.<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Checking latency on a Cisco router starts with quick CLI validation using extended <code>ping<\/code> and <code>traceroute<\/code>\u2014while avoiding the misconception that the static <code>DLY<\/code> metric in <code>show interfaces<\/code> reflects live network delay. By pairing continuous on-box IP SLA probes with structured control-plane and interface queue diagnostics, and feeding those metrics into an SNMP-aware monitoring platform, you can pinpoint network slowdowns and maintain predictable WAN performance.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-latency-in-cisco-router_24585.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+Latency+in+Cisco+Router+https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\",\"How to Check Latency in Cisco Router\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Measuring network latency directly from a Cisco router allows network engineers to isolate WAN slowdowns, verify service provider SLAs, and distinguish between transit link congestion and local device bottlenecks. Whether you need an immediate round-trip time (RTT) measurement between two endpoints or continuous telemetry tracking microsecond jitter across voice and video paths, Cisco IOS and&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check Latency in Cisco Router - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check Latency in Cisco Router - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Measuring network latency directly from a Cisco router allows network engineers to isolate WAN slowdowns, verify service provider SLAs, and distinguish between transit link congestion and local device bottlenecks. Whether you need an immediate round-trip time (RTT) measurement between two endpoints or continuous telemetry tracking microsecond jitter across voice and video paths, Cisco IOS and... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T07:40:16+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"10 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\",\"name\":\"How to Check Latency in Cisco Router - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T07:40:16+00:00\",\"dateModified\":\"2026-11-17T07:40:16+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check Latency in Cisco Router\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check Latency in Cisco Router\",\"datePublished\":\"2026-11-17T07:40:16+00:00\",\"dateModified\":\"2026-11-17T07:40:16+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage\"},\"wordCount\":1590,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check Latency in Cisco Router - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html","og_locale":"en_US","og_type":"article","og_title":"How to Check Latency in Cisco Router - SPOTO Official Blog","og_description":"Measuring network latency directly from a Cisco router allows network engineers to isolate WAN slowdowns, verify service provider SLAs, and distinguish between transit link congestion and local device bottlenecks. Whether you need an immediate round-trip time (RTT) measurement between two endpoints or continuous telemetry tracking microsecond jitter across voice and video paths, Cisco IOS and... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T07:40:16+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"10 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html","name":"How to Check Latency in Cisco Router - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T07:40:16+00:00","dateModified":"2026-11-17T07:40:16+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check Latency in Cisco Router"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check Latency in Cisco Router","datePublished":"2026-11-17T07:40:16+00:00","dateModified":"2026-11-17T07:40:16+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#webpage"},"wordCount":1590,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-latency-in-cisco-router_24585.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24585"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24585"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24585\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24585"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24585"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24585"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}