{"id":24581,"date":"2026-11-17T15:25:20","date_gmt":"2026-11-17T07:25:20","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html"},"modified":"2026-11-17T15:25:20","modified_gmt":"2026-11-17T07:25:20","slug":"how-to-check-if-multicast-is-enabled-on-cisco-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html","title":{"rendered":"How to Check if Multicast Is Enabled on Cisco Switch"},"content":{"rendered":"<p>Verifying whether multicast is enabled on a Cisco switch requires checking two distinct layers of the network stack. A switch operating purely at Layer 2 handles multicast traffic very differently from a multilayer switch routing multicast streams between VLANs. Before running verification commands, you need to determine whether your switch is responsible for local Layer 2 traffic optimization (IGMP snooping) or inter-VLAN Layer 3 packet forwarding (IP multicast routing and PIM).<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Layer_2_IGMP_Snooping_vs_Layer_3_IP_Multicast_Routing\" title=\"Layer 2 IGMP Snooping vs. Layer 3 IP Multicast Routing\">Layer 2 IGMP Snooping vs. Layer 3 IP Multicast Routing<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#How_to_Check_if_Layer_2_IGMP_Snooping_Is_Enabled\" title=\"How to Check if Layer 2 IGMP Snooping Is Enabled\">How to Check if Layer 2 IGMP Snooping Is Enabled<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Step_1_Verify_Global_and_Per-VLAN_IGMP_Snooping_Status\" title=\"Step 1: Verify Global and Per-VLAN IGMP Snooping Status\">Step 1: Verify Global and Per-VLAN IGMP Snooping Status<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Step_2_Check_for_an_Active_IGMP_Querier\" title=\"Step 2: Check for an Active IGMP Querier\">Step 2: Check for an Active IGMP Querier<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Step_3_Inspect_Learned_Multicast_Groups_and_Router_Ports\" title=\"Step 3: Inspect Learned Multicast Groups and Router Ports\">Step 3: Inspect Learned Multicast Groups and Router Ports<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#CLI_Commands_to_Verify_Layer_3_IP_Multicast_Routing_and_PIM\" title=\"CLI Commands to Verify Layer 3 IP Multicast Routing and PIM\">CLI Commands to Verify Layer 3 IP Multicast Routing and PIM<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#How_to_Enable_IP_Multicast_Routing_and_PIM_on_a_Cisco_Switch\" title=\"How to Enable IP Multicast Routing and PIM on a Cisco Switch\">How to Enable IP Multicast Routing and PIM on a Cisco Switch<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#How_to_Check_Multicast_and_PIM_Status_on_a_Cisco_Nexus_Switch\" title=\"How to Check Multicast and PIM Status on a Cisco Nexus Switch\">How to Check Multicast and PIM Status on a Cisco Nexus Switch<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Troubleshooting_Multicast_Traffic_Not_Passing_Through_a_Cisco_Switch\" title=\"Troubleshooting Multicast Traffic Not Passing Through a Cisco Switch\">Troubleshooting Multicast Traffic Not Passing Through a Cisco Switch<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#1_Fix_Missing_IGMP_Queriers_in_Layer_2-Only_Environments\" title=\"1. Fix Missing IGMP Queriers in Layer 2-Only Environments\">1. Fix Missing IGMP Queriers in Layer 2-Only Environments<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#2_Verify_Rendezvous_Point_RP_Mapping_and_Reachability\" title=\"2. Verify Rendezvous Point (RP) Mapping and Reachability\">2. Verify Rendezvous Point (RP) Mapping and Reachability<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#3_Check_for_Reverse_Path_Forwarding_RPF_Failures\" title=\"3. Check for Reverse Path Forwarding (RPF) Failures\">3. Check for Reverse Path Forwarding (RPF) Failures<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#4_Inspect_Packet_TTL_and_Reserved_Multicast_Addresses\" title=\"4. Inspect Packet TTL and Reserved Multicast Addresses\">4. Inspect Packet TTL and Reserved Multicast Addresses<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#5_Monitor_Active_Hardware_Forwarding_Counters\" title=\"5. Monitor Active Hardware Forwarding Counters\">5. Monitor Active Hardware Forwarding Counters<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Official_Cisco_Multicast_Configuration_Guides_and_Command_References\" title=\"Official Cisco Multicast Configuration Guides and Command References\">Official Cisco Multicast Configuration Guides and Command References<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Layer_2_IGMP_Snooping_vs_Layer_3_IP_Multicast_Routing\"><\/span>Layer 2 IGMP Snooping vs. Layer 3 IP Multicast Routing<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>On Cisco Catalyst switches, &#8220;multicast&#8221; refers to two separate mechanisms with opposite default states. Layer 2 IGMP snooping listens to host-to-router messages so the switch only forwards multicast frames to ports with interested receivers, rather than flooding the entire VLAN. Layer 3 IP multicast routing actively routes multicast packets across subnet boundaries using Protocol Independent Multicast (PIM).<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Feature \/ Criterion<\/th>\n<th style=\"text-align: left;\">Layer 2 IGMP Snooping<\/th>\n<th style=\"text-align: left;\">Layer 3 IP Multicast Routing<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>OSI Layer<\/strong><\/td>\n<td style=\"text-align: left;\">Layer 2 (Data Link)<\/td>\n<td style=\"text-align: left;\">Layer 3 (Network)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Default Status (Catalyst IOS\/IOS-XE)<\/strong><\/td>\n<td style=\"text-align: left;\"><strong>Enabled<\/strong> by default globally and on all VLANs<\/td>\n<td style=\"text-align: left;\"><strong>Disabled<\/strong> by default globally and on all interfaces<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Primary Function<\/strong><\/td>\n<td style=\"text-align: left;\">Prevents Layer 2 multicast broadcast flooding within a single VLAN by examining IGMP reports<\/td>\n<td style=\"text-align: left;\">Routes multicast streams between different VLANs (SVIs) or routed physical ports<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Core Protocols Used<\/strong><\/td>\n<td style=\"text-align: left;\">IGMPv1\/v2\/v3 Snooping, IGMP Snooping Querier<\/td>\n<td style=\"text-align: left;\">PIM Sparse Mode (PIM-SM), PIM-SSM, PIM Dense Mode, IGMP, MSDP<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Cisco Licensing (Catalyst 9000)<\/strong><\/td>\n<td style=\"text-align: left;\">Included in Network Essentials (Base)<\/td>\n<td style=\"text-align: left;\">Requires Network Advantage (for full L3 multicast routing)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Primary Verification Command<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show ip igmp snooping<\/code><\/td>\n<td style=\"text-align: left;\"><code>show ip multicast<\/code> and <code>show ip pim interface<\/code><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Understanding this distinction ensures you check the right subsystem: if your hosts and multicast server sit in the same VLAN, you only need to verify IGMP snooping; if they sit in different subnets, you must check both IGMP snooping and Layer 3 multicast routing.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Check_if_Layer_2_IGMP_Snooping_Is_Enabled\"><\/span>How to Check if Layer 2 IGMP Snooping Is Enabled<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Even though IGMP snooping is enabled out of the box on Cisco Catalyst switches, administrators occasionally disable it on specific VLANs during troubleshooting or misconfigure the IGMP querier needed to keep group memberships alive. Follow these sequential steps to verify Layer 2 multicast functionality.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Verify_Global_and_Per-VLAN_IGMP_Snooping_Status\"><\/span>Step 1: Verify Global and Per-VLAN IGMP Snooping Status<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run the <code>show ip igmp snooping<\/code> command in privileged EXEC mode to inspect both the global switch state and individual VLAN settings. You can also append <code>vlan &lt;vlan-id&gt;<\/code> to filter the output to a single broadcast domain.<\/p>\n<pre><code class=\"language-text\">Switch# show ip igmp snooping vlan 10\nGlobal IGMP Snooping configuration:\n-------------------------------------------\nIGMP snooping                : Enabled\nIGMPv3 snooping (minimal)    : Enabled\nReport suppression           : Enabled\nTCN solicit query            : Disabled\nTCN flood query count        : 2\nRobustness variable          : 2\nLast member query count      : 2\nLast member query interval   : 1000\n\nVlan 10:\n--------\nIGMP snooping                       : Enabled\nIGMPv2 immediate leave              : Disabled\nExplicit host tracking              : Enabled\nMulticast router learning mode      : pim-dvmrp\nCGMP interoperability mode          : IGMP_ONLY\n<\/code><\/pre>\n<p>Confirm that <strong>both<\/strong> <code>Global IGMP Snooping configuration<\/code> and the specific <code>Vlan &lt;id&gt;<\/code> entry display <code>Enabled<\/code>. If global snooping is disabled, per-VLAN settings have no effect, and the switch floods all multicast traffic across every port in the VLAN like a broadcast.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_for_an_Active_IGMP_Querier\"><\/span>Step 2: Check for an Active IGMP Querier<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>IGMP snooping relies on periodic IGMP General Queries sent by a multicast router to prompt hosts to report their group memberships. Without a querier, the switch&#8217;s snooping table times out after a few minutes and drops multicast streams. Check if an active querier exists on your VLANs:<\/p>\n<pre><code class=\"language-text\">Switch# show ip igmp snooping querier\nVlan      IP Address               IGMP Version   Port             \n-------------------------------------------------------------\n10        10.10.10.1               v2             Switch\n20        10.10.20.254             v2             Gi1\/0\/1\n<\/code><\/pre>\n<p>If a VLAN is missing from this output or shows <code>0.0.0.0<\/code>, no device is sending membership queries on that subnet.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Inspect_Learned_Multicast_Groups_and_Router_Ports\"><\/span>Step 3: Inspect Learned Multicast Groups and Router Ports<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Once snooping and a querier are confirmed, verify that the switch is actively learning multicast group joins from receivers and identifying the upstream multicast router port (<code>mrouter<\/code>):<\/p>\n<pre><code class=\"language-text\">Switch# show ip igmp snooping groups vlan 10\nVlan      Group                    Type        Version     Port List\n-----------------------------------------------------------------------\n10        239.1.1.100              igmp        v2          Gi1\/0\/12, Gi1\/0\/15\n\nSwitch# show ip igmp snooping mrouter vlan 10\nVlan    ports\n----    -----\n  10    Gi1\/0\/1(dynamic)\n<\/code><\/pre>\n<p>If receivers are actively requesting a stream, their access ports appear under <code>Port List<\/code>, and the uplink toward the router or SVI appears under <code>mrouter<\/code>.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"CLI_Commands_to_Verify_Layer_3_IP_Multicast_Routing_and_PIM\"><\/span>CLI Commands to Verify Layer 3 IP Multicast Routing and PIM<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When a Cisco Catalyst switch acts as the default gateway routing multicast traffic between VLANs, you must verify that global IP multicast routing is turned on and that PIM is active on each participating Layer 3 interface. Use the following IOS and IOS-XE CLI commands and compare your results against the expected outputs.<\/p>\n<pre><code class=\"language-text\">! 1. Verify global Layer 3 multicast routing status\nSwitch# show ip multicast\n  Multicast Routing: enabled\n  Multicast Multipath: disabled\n  Multicast Route limit: No limit\n  Multicast Fallback group mode: Sparse\n\n! Alternative check against the running configuration:\nSwitch# show running-config | include ip multicast-routing\nip multicast-routing distributed\n\n\n! 2. Verify which Layer 3 interfaces (SVIs or routed ports) have PIM enabled\nSwitch# show ip pim interface\nAddress          Interface                Ver\/   Nbr    Query  DR     DR\n                                          Mode   Count  Intvl  Prior\n10.10.10.1       Vlan10                   v2\/S   1      30     1      10.10.10.2\n10.10.20.1       Vlan20                   v2\/S   0      30     1      10.10.20.1\n172.16.0.2       GigabitEthernet1\/0\/48    v2\/S   1      30     1      172.16.0.1\n! Note: &quot;v2\/S&quot; indicates PIMv2 Sparse Mode is active on the interface.\n! If this output is blank, PIM is not configured on any interface.\n\n\n! 3. Check active PIM neighbor adjacencies with upstream\/downstream routers\nSwitch# show ip pim neighbor\nPIM Neighbor Table\nMode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority,\n      P - Proxy Capable, S - State Refresh Capable, G - GenID Capable,\n      L - DR Load-balancing Capable\nNeighbor          Interface                Uptime\/Expires    Ver   DR\nAddress                                                            Prio\/Mode\n10.10.10.2        Vlan10                   02:14:09\/00:01:28 v2    1 \/ DR S P G\n172.16.0.1        GigabitEthernet1\/0\/48    05:41:22\/00:01:41 v2    100\/ DR S P G\n\n\n! 4. Inspect the active Layer 3 Multicast Routing Table (mroute)\nSwitch# show ip mroute 239.1.1.100\n(*, 239.1.1.100), 00:15:32\/stopped, RP 10.255.255.1, flags: SJC\n  Incoming interface: GigabitEthernet1\/0\/48, RPF nbr 172.16.0.1\n  Outgoing interface list:\n    Vlan10, Forward\/Sparse, 00:15:32\/00:02:41\n\n(10.10.20.50, 239.1.1.100), 00:12:10\/00:02:51, flags: FT\n  Incoming interface: Vlan20, RPF nbr 0.0.0.0\n  Outgoing interface list:\n    Vlan10, Forward\/Sparse, 00:12:10\/00:02:41\n<\/code><\/pre>\n<p>If <code>show ip multicast<\/code> returns <code>Multicast Routing: disabled<\/code> or <code>show ip pim interface<\/code> returns no entries, the switch will drop all inter-VLAN multicast traffic at the Layer 3 boundary.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Enable_IP_Multicast_Routing_and_PIM_on_a_Cisco_Switch\"><\/span>How to Enable IP Multicast Routing and PIM on a Cisco Switch<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>If your verification commands reveal that Layer 3 multicast routing is disabled, use the following configuration template to enable it. Note that Catalyst 3650\/3850 and Catalyst 9000 series switches running Cisco IOS-XE use <code>ip multicast-routing distributed<\/code>, whereas classic IOS switches use <code>ip multicast-routing<\/code>.<\/p>\n<pre><code class=\"language-text\">configure terminal\n\n! 1. Enable global IP multicast routing\n! Use &quot;ip multicast-routing distributed&quot; on Catalyst IOS-XE platforms,\n! or &quot;ip multicast-routing&quot; on classic Catalyst IOS platforms:\nip multicast-routing distributed\n\n! 2. Configure the Rendezvous Point (RP) address for PIM Sparse Mode\n! (All multicast routers in the domain must agree on the RP IP address)\nip pim rp-address &lt;rp-loopback-ip&gt;\n\n! 3. Enable PIM Sparse Mode on every SVI and routed uplink that carries multicast\ninterface Vlan&lt;source-vlan-id&gt;\n ip address &lt;ip-address&gt; &lt;subnet-mask&gt;\n ip pim sparse-mode\n exit\n\ninterface Vlan&lt;receiver-vlan-id&gt;\n ip address &lt;ip-address&gt; &lt;subnet-mask&gt;\n ip pim sparse-mode\n exit\n\ninterface &lt;routed-uplink-interface&gt;\n no switchport\n ip address &lt;ip-address&gt; &lt;subnet-mask&gt;\n ip pim sparse-mode\n exit\n\n! 4. Save the configuration\nend\nwrite memory\n<\/code><\/pre>\n<p>Enabling <code>ip pim sparse-mode<\/code> on an SVI automatically enables IGMP on that interface as well, allowing the switch to act as the IGMP querier for that VLAN.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Check_Multicast_and_PIM_Status_on_a_Cisco_Nexus_Switch\"><\/span>How to Check Multicast and PIM Status on a Cisco Nexus Switch<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Data center networks running Cisco Nexus switches use NX-OS, which employs a modular feature-based architecture rather than the monolithic command structure of Catalyst IOS-XE. On NX-OS, multicast protocols do not even appear in the configuration or verification CLI until their corresponding features are enabled. Use the commands below to check multicast status on a Cisco Nexus switch.<\/p>\n<pre><code class=\"language-text\">! 1. Check if the PIM, IGMP, and MSDP features are enabled in NX-OS\nNexus-Switch# show feature | include &quot;pim|igmp|msdp&quot;\nigmp                  1          enabled\nmsdp                  1          disabled\npim                   1          enabled\npim6                  1          disabled\n\n\n! 2. Verify Layer 2 IGMP snooping status (enabled by default in NX-OS)\nNexus-Switch# show ip igmp snooping\nGlobal IGMP Snooping Information:\n  IGMP Snooping enabled\n  Optimised Multicast Flood (OMF) enabled\n  IGMPv1\/v2 Report Suppression enabled\n  IGMPv3 Report Suppression disabled\n  Link Local Groups Suppression enabled\n\n\n! 3. Check Layer 3 interfaces configured for PIM in the current VRF\nNexus-Switch# show ip pim interface brief\nPIM Interface Status for VRF &quot;default&quot;\nInterface               IP Address       PIM DR Address   Neighbor  Border\n                                                          Count     Interface\nVlan10                  10.10.10.1\/24    10.10.10.1          0      no\nEthernet1\/49            172.16.0.2\/30    172.16.0.1          1      no\n\n\n! 4. Verify active PIM neighbors and the NX-OS multicast routing table\nNexus-Switch# show ip pim neighbor\nNexus-Switch# show ip mroute\n<\/code><\/pre>\n<p>If <code>show feature<\/code> indicates that <code>pim<\/code> or <code>igmp<\/code> is <code>disabled<\/code> on a Nexus switch, enable them in global configuration mode using <code>feature pim<\/code> and <code>feature igmp<\/code> before configuring interfaces.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Troubleshooting_Multicast_Traffic_Not_Passing_Through_a_Cisco_Switch\"><\/span>Troubleshooting Multicast Traffic Not Passing Through a Cisco Switch<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Sometimes all verification checks confirm that IGMP snooping, global multicast routing, and PIM are enabled, yet receivers still fail to receive multicast streams. Follow this diagnostic guide to isolate the root cause.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"1_Fix_Missing_IGMP_Queriers_in_Layer_2-Only_Environments\"><\/span>1. Fix Missing IGMP Queriers in Layer 2-Only Environments<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If multicast sources and receivers reside in the same isolated Layer 2 VLAN without a PIM-enabled router or SVI, IGMP snooping will stop forwarding traffic after 3 to 4 minutes because no device sends periodic IGMP Membership Queries.<br \/>\n* <strong>Diagnosis:<\/strong> Run <code>show ip igmp snooping querier<\/code> as covered above.<br \/>\n* <strong>Resolution:<\/strong> Enable the switch&#8217;s built-in Layer 2 IGMP snooping querier on that VLAN (make sure the switch has an SVI IP address or assign a dummy querier IP):<br \/>\n  <code>text<br \/>\n  Switch(config)# ip igmp snooping vlan 10 querier<br \/>\n  Switch(config)# ip igmp snooping vlan 10 querier address 10.10.10.254<\/code><\/p>\n<h3><span class=\"ez-toc-section\" id=\"2_Verify_Rendezvous_Point_RP_Mapping_and_Reachability\"><\/span>2. Verify Rendezvous Point (RP) Mapping and Reachability<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>In PIM Sparse Mode, switches cannot build shared trees <code>(*, G)<\/code> or register sources <code>(S, G)<\/code> unless they know the IP address of the Rendezvous Point and can reach it via unicast routing.<br \/>\n* <strong>Diagnosis:<\/strong> Run <code>show ip pim rp mapping<\/code> to verify that an RP is configured or learned via Auto-RP\/BSR, and test unicast connectivity with <code>ping &lt;rp-ip&gt;<\/code>.<br \/>\n* <strong>Resolution:<\/strong> Ensure every Layer 3 switch in the multicast path has a matching <code>ip pim rp-address<\/code> statement (or valid Auto-RP\/BSR configuration) and a valid unicast route to the RP&#8217;s loopback interface.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"3_Check_for_Reverse_Path_Forwarding_RPF_Failures\"><\/span>3. Check for Reverse Path Forwarding (RPF) Failures<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Layer 3 multicast switches drop incoming multicast packets if the interface they arrive on does not match the outgoing interface the switch uses to reach the source&#8217;s unicast IP address.<br \/>\n* <strong>Diagnosis:<\/strong> Run <code>show ip rpf &lt;multicast-source-ip&gt;<\/code>. Look at the <code>RPF interface<\/code> and <code>RPF neighbor<\/code> fields:<br \/>\n  <code>text<br \/>\n  Switch# show ip rpf 10.10.20.50<br \/>\n  RPF information for ? (10.10.20.50)<br \/>\n    RPF interface: Vlan20<br \/>\n    RPF neighbor: ? (0.0.0.0) - directly connected<br \/>\n    RPF route\/mask: 10.10.20.0\/24<br \/>\n    RPF type: unicast (connected)<\/code><br \/>\n* <strong>Resolution:<\/strong> If <code>show ip rpf<\/code> reports <code>failed, no route exists<\/code> or points to an interface where PIM is disabled, fix the underlying unicast routing asymmetry or add a static multicast route (<code>ip mroute &lt;source-ip&gt; &lt;mask&gt; &lt;next-hop&gt;<\/code>).<\/p>\n<h3><span class=\"ez-toc-section\" id=\"4_Inspect_Packet_TTL_and_Reserved_Multicast_Addresses\"><\/span>4. Inspect Packet TTL and Reserved Multicast Addresses<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Two common application-level mistakes prevent Cisco switches from routing multicast packets across VLANs even when network configuration is flawless:<br \/>\n* <strong>TTL = 1:<\/strong> Many streaming applications default to a Time-to-Live (TTL) value of <code>1<\/code>. When a Layer 3 switch routes the packet to another VLAN, it decrements the TTL to <code>0<\/code> and drops the packet. Increase the sender&#8217;s multicast TTL setting to at least <code>15<\/code> or <code>64<\/code>.<br \/>\n* <strong>Link-Local Address Range (<code>224.0.0.0\/24<\/code>):<\/strong> Addresses from <code>224.0.0.0<\/code> to <code>224.0.0.255<\/code> are reserved by IANA for link-local control protocols (such as OSPF and VRRP). Cisco switches never route packets in this range across Layer 3 boundaries, regardless of TTL. Use organization-local multicast addresses in the <code>239.0.0.0\/8<\/code> block instead.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"5_Monitor_Active_Hardware_Forwarding_Counters\"><\/span>5. Monitor Active Hardware Forwarding Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To verify whether the switch is receiving multicast packets from the source and forwarding them out the OIL (Outgoing Interface List), check the packet counters:<\/p>\n<pre><code class=\"language-text\">Switch# show ip mroute count\n<\/code><\/pre>\n<p>Look at the <code>(S, G)<\/code> entry for your stream. If <code>Other counts: RPF failed<\/code> or <code>Total\/Other drops<\/code> increments while <code>Forwarded<\/code> stays at zero, the switch is dropping the stream due to RPF mismatches or an empty outgoing interface list.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Official_Cisco_Multicast_Configuration_Guides_and_Command_References\"><\/span>Official Cisco Multicast Configuration Guides and Command References<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>For platform-specific syntax variations, hardware forwarding scale limits, and release-specific caveats, consult the authoritative Cisco documentation corresponding to your switch hardware and software train:<\/p>\n<ul>\n<li><strong>Cisco Catalyst 9000 Series (IOS-XE):<\/strong> Refer to the <em>IP Multicast Routing Configuration Guide, Cisco IOS XE [Release] (Catalyst 9200 \/ 9300 \/ 9400 \/ 9500 \/ 9600 Switches)<\/em>.<\/li>\n<li><em>Licensing Note:<\/em> Full Layer 3 PIM Sparse Mode (<code>ip pim sparse-mode<\/code>), PIM-SSM, and MSDP require the <strong>Network Advantage<\/strong> license package. Switches running Network Essentials only support Layer 2 IGMP snooping and basic PIM stub routing.<\/li>\n<li><em>Hardware Verification:<\/em> On Catalyst 9000 switches, use <code>show platform software fed switch active ipmcast info<\/code> to inspect ASIC-level multicast forwarding resources.<\/li>\n<li><strong>Cisco Catalyst 3650 \/ 3850 Series (IOS-XE):<\/strong> Refer to the <em>IP Multicast Routing Configuration Guide, Cisco IOS XE Denali \/ Everest \/ Fuji \/ Gibraltar (Catalyst 3650 and 3850 Switches)<\/em>.<\/li>\n<li><strong>Cisco IOS Master Command Reference:<\/strong> Refer to the <em>Cisco IOS IP Multicast Command Reference<\/em> for complete syntax descriptions and output field definitions for all <code>show ip igmp<\/code>, <code>show ip pim<\/code>, and <code>show ip mroute<\/code> commands.<\/li>\n<li><strong>Cisco Nexus 9000 Series (NX-OS):<\/strong> Refer to the <em>Cisco Nexus 9000 Series NX-OS Multicast Routing Configuration Guide<\/em> for VXLAN EVPN multicast underlay\/overlay verification, Anycast RP, and NX-OS specific CLI syntax.<\/li>\n<\/ul>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Checking whether multicast is enabled on a Cisco switch comes down to verifying the right layer for your topology. For single-VLAN environments, run <code>show ip igmp snooping<\/code> and <code>show ip igmp snooping querier<\/code> to confirm that Layer 2 filtering and membership queries are active. For multi-VLAN environments, run <code>show ip multicast<\/code> and <code>show ip pim interface<\/code> (or <code>show feature<\/code> on Nexus NX-OS) to confirm that Layer 3 multicast routing and PIM are enabled across your SVIs and uplinks. Combining these verification checks with RPF and RP diagnostics ensures your multicast streams flow reliably from source to receiver.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+if+Multicast+Is+Enabled+on+Cisco+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\",\"How to Check if Multicast Is Enabled on Cisco Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Verifying whether multicast is enabled on a Cisco switch requires checking two distinct layers of the network stack. A switch operating purely at Layer 2 handles multicast traffic very differently from a multilayer switch routing multicast streams between VLANs. Before running verification commands, you need to determine whether your switch is responsible for local Layer&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Verifying whether multicast is enabled on a Cisco switch requires checking two distinct layers of the network stack. A switch operating purely at Layer 2 handles multicast traffic very differently from a multilayer switch routing multicast streams between VLANs. Before running verification commands, you need to determine whether your switch is responsible for local Layer... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T07:25:20+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"11 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\",\"name\":\"How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T07:25:20+00:00\",\"dateModified\":\"2026-11-17T07:25:20+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check if Multicast Is Enabled on Cisco Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check if Multicast Is Enabled on Cisco Switch\",\"datePublished\":\"2026-11-17T07:25:20+00:00\",\"dateModified\":\"2026-11-17T07:25:20+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage\"},\"wordCount\":1461,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html","og_locale":"en_US","og_type":"article","og_title":"How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog","og_description":"Verifying whether multicast is enabled on a Cisco switch requires checking two distinct layers of the network stack. A switch operating purely at Layer 2 handles multicast traffic very differently from a multilayer switch routing multicast streams between VLANs. Before running verification commands, you need to determine whether your switch is responsible for local Layer... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T07:25:20+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"11 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html","name":"How to Check if Multicast Is Enabled on Cisco Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T07:25:20+00:00","dateModified":"2026-11-17T07:25:20+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check if Multicast Is Enabled on Cisco Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check if Multicast Is Enabled on Cisco Switch","datePublished":"2026-11-17T07:25:20+00:00","dateModified":"2026-11-17T07:25:20+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#webpage"},"wordCount":1461,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-if-multicast-is-enabled-on-cisco-switch_24581.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24581"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24581"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24581\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24581"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24581"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24581"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}