{"id":24577,"date":"2026-11-17T15:09:35","date_gmt":"2026-11-17T07:09:35","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html"},"modified":"2026-11-17T15:09:35","modified_gmt":"2026-11-17T07:09:35","slug":"how-to-check-flapping-in-cisco-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html","title":{"rendered":"How to Check Flapping in Cisco Switch"},"content":{"rendered":"<p>Network instability on a Cisco switch often manifests in one of two ways: physical <strong>port (link) flapping<\/strong>, where an interface repeatedly cycles between <code>up<\/code> and <code>down<\/code> states, or Layer 2 <strong>MAC address flapping<\/strong>, where the switch continuously relearns the same hardware address across different ports. Both conditions degrade application performance, trigger Spanning Tree Protocol (STP) topology recalculations, and can eventually force interfaces into an administrative shutdown. Diagnosing flapping quickly requires isolating whether the fault lies at Layer 1 (physical media and transceivers) or Layer 2 (forwarding loops and host roaming), and then applying the appropriate Cisco IOS, IOS-XE, or NX-OS verification commands.<\/p>\n<hr \/>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step-by-Step_CLI_Guide_to_Check_Physical_Port_Flapping_History_and_Logs\" title=\"Step-by-Step CLI Guide to Check Physical Port Flapping History and Logs\">Step-by-Step CLI Guide to Check Physical Port Flapping History and Logs<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_1_Inspect_the_Local_Syslog_Buffer_for_Link_State_Changes\" title=\"Step 1: Inspect the Local Syslog Buffer for Link State Changes\">Step 1: Inspect the Local Syslog Buffer for Link State Changes<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_2_Check_Interface_Reset_Counters_and_Last_Flap_Timestamps\" title=\"Step 2: Check Interface Reset Counters and Last Flap Timestamps\">Step 2: Check Interface Reset Counters and Last Flap Timestamps<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_3_Check_Port_UpDown_History_with_show_interface_link\" title=\"Step 3: Check Port Up\/Down History with show interface link\">Step 3: Check Port Up\/Down History with show interface link<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_4_Verify_If_the_Port_Was_Shut_Down_Into_an_err-disabled_State\" title=\"Step 4: Verify If the Port Was Shut Down Into an err-disabled State\">Step 4: Verify If the Port Was Shut Down Into an err-disabled State<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Understanding_the_Causes_of_Port_Flapping_and_the_link-flap_Errdisable_State\" title=\"Understanding the Causes of Port Flapping and the link-flap Errdisable State\">Understanding the Causes of Port Flapping and the link-flap Errdisable State<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Why_is_my_Cisco_switch_interface_going_up_and_down_repeatedly\" title=\"Why is my Cisco switch interface going up and down repeatedly?\">Why is my Cisco switch interface going up and down repeatedly?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Why_does_a_Cisco_switch_put_a_flapping_port_into_an_err-disabled_state\" title=\"Why does a Cisco switch put a flapping port into an err-disabled state?\">Why does a Cisco switch put a flapping port into an err-disabled state?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#How_do_I_check_the_current_link-flap_threshold_values_on_my_switch\" title=\"How do I check the current link-flap threshold values on my switch?\">How do I check the current link-flap threshold values on my switch?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Configuration_Templates_Link-Flap_Thresholds_Auto-Recovery_and_Interface_Dampening\" title=\"Configuration Templates: Link-Flap Thresholds, Auto-Recovery, and Interface Dampening\">Configuration Templates: Link-Flap Thresholds, Auto-Recovery, and Interface Dampening<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#1_Enable_Automatic_Errdisable_Recovery_for_Link-Flap_Events\" title=\"1. Enable Automatic Errdisable Recovery for Link-Flap Events\">1. Enable Automatic Errdisable Recovery for Link-Flap Events<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#2_Customize_Link-Flap_Error_Thresholds\" title=\"2. Customize Link-Flap Error Thresholds\">2. Customize Link-Flap Error Thresholds<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#3_Manually_Reset_an_Err-Disabled_Interface_Plus_EEE_Mitigation\" title=\"3. Manually Reset an Err-Disabled Interface (Plus EEE Mitigation)\">3. Manually Reset an Err-Disabled Interface (Plus EEE Mitigation)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#4_Configure_Interface_Event_Dampening_Routed_Layer_3_Ports\" title=\"4. Configure Interface Event Dampening (Routed \/ Layer 3 Ports)\">4. Configure Interface Event Dampening (Routed \/ Layer 3 Ports)<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#How_to_Check_and_Troubleshoot_Layer_2_MAC_Address_Flapping\" title=\"How to Check and Troubleshoot Layer 2 MAC Address Flapping\">How to Check and Troubleshoot Layer 2 MAC Address Flapping<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_1_Identify_the_Flapping_MAC_Address_VLAN_and_Ports_in_Syslog\" title=\"Step 1: Identify the Flapping MAC Address, VLAN, and Ports in Syslog\">Step 1: Identify the Flapping MAC Address, VLAN, and Ports in Syslog<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_2_Check_Current_MAC_Table_Learning_and_Trace_Neighboring_Devices\" title=\"Step 2: Check Current MAC Table Learning and Trace Neighboring Devices\">Step 2: Check Current MAC Table Learning and Trace Neighboring Devices<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_3_Distinguish_Benign_Host_Movement_from_Dangerous_Layer_2_Loops\" title=\"Step 3: Distinguish Benign Host Movement from Dangerous Layer 2 Loops\">Step 3: Distinguish Benign Host Movement from Dangerous Layer 2 Loops<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Step_4_Pinpoint_and_Break_a_Layer_2_Loop_Using_Input_Packet_Rates_and_STP_Counters\" title=\"Step 4: Pinpoint and Break a Layer 2 Loop Using Input Packet Rates and STP Counters\">Step 4: Pinpoint and Break a Layer 2 Loop Using Input Packet Rates and STP Counters<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Best_Network_Monitoring_Tools_to_Detect_Cisco_Switch_Flapping_Proactively\" title=\"Best Network Monitoring Tools to Detect Cisco Switch Flapping Proactively\">Best Network Monitoring Tools to Detect Cisco Switch Flapping Proactively<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Official_Cisco_Documentation_and_Platform_Diagnostic_References\" title=\"Official Cisco Documentation and Platform Diagnostic References\">Official Cisco Documentation and Platform Diagnostic References<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Official_Cisco_Support_Guides_and_Command_References\" title=\"Official Cisco Support Guides and Command References\">Official Cisco Support Guides and Command References<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Platform-Specific_Hardware_Diagnostic_Commands\" title=\"Platform-Specific Hardware Diagnostic Commands\">Platform-Specific Hardware Diagnostic Commands<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-24\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_CLI_Guide_to_Check_Physical_Port_Flapping_History_and_Logs\"><\/span>Step-by-Step CLI Guide to Check Physical Port Flapping History and Logs<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>To identify which physical interfaces are cycling up and down, inspect the switch&#8217;s system message buffer, interface reset counters, and hardware link-state history across Cisco Catalyst (IOS\/IOS-XE) and Cisco Nexus (NX-OS) platforms.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Inspect_the_Local_Syslog_Buffer_for_Link_State_Changes\"><\/span>Step 1: Inspect the Local Syslog Buffer for Link State Changes<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Whenever a physical interface transitions between states, the operating system generates <code>%LINK-3-UPDOWN<\/code> (physical layer) and <code>%LINEPROTO-5-UPDOWN<\/code> (data link layer) messages. Filter the log buffer to spot repeating timestamps on the same port:<\/p>\n<pre><code class=\"language-ios\">! Cisco IOS \/ IOS-XE: View all link up\/down events\nSwitch# show logging | include UPDOWN\n\n! Filter logs for a specific suspect interface\nSwitch# show logging | include GigabitEthernet1\/0\/10\n<\/code><\/pre>\n<p>Typical output confirming a physical port flap looks like this:<\/p>\n<pre><code class=\"language-text\">Oct 05 14:12:01.114: %LINK-3-UPDOWN: Interface GigabitEthernet1\/0\/10, changed state to down\nOct 05 14:12:03.418: %LINK-3-UPDOWN: Interface GigabitEthernet1\/0\/10, changed state to up\nOct 05 14:12:04.419: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1\/0\/10, changed state to up\n<\/code><\/pre>\n<p>On <strong>Cisco NX-OS<\/strong>, filter the logfile for <code>ETHPORT-5-IF_DOWN<\/code> and <code>ETHPORT-5-IF_UP<\/code> events:<\/p>\n<pre><code class=\"language-ios\">Nexus# show logging logfile | include ETHPORT-5-IF\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_Interface_Reset_Counters_and_Last_Flap_Timestamps\"><\/span>Step 2: Check Interface Reset Counters and Last Flap Timestamps<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Even if the circular syslog buffer has rolled over, individual interface counters preserve historical evidence of instability. Inspect the <code>interface resets<\/code> counter and physical layer error statistics:<\/p>\n<pre><code class=\"language-ios\">! Cisco IOS \/ IOS-XE: Check resets, input errors, and CRC counters\nSwitch# show interfaces GigabitEthernet1\/0\/10 | include line protocol|resets|CRC|input errors\n<\/code><\/pre>\n<p>Look for a rising <strong>interface resets<\/strong> count paired with <strong>CRC<\/strong>, <strong>frame<\/strong>, or <strong>input errors<\/strong>, which point to damaged cabling or failing optics.<\/p>\n<p>On <strong>Cisco NX-OS<\/strong>, the <code>show interface<\/code> output includes an explicit <code>Last link flapped<\/code> timer alongside the reset counter:<\/p>\n<pre><code class=\"language-ios\">Nexus# show interface Ethernet1\/1 | include &quot;is |flapped|resets&quot;\nEthernet1\/1 is up\n  Last link flapped 00:04:12\n  14 interface resets\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Check_Port_UpDown_History_with_show_interface_link\"><\/span>Step 3: Check Port Up\/Down History with <code>show interface link<\/code><span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On supported Cisco Catalyst switches (such as Catalyst 4500, 6500, and 9000 Series), examine the time-since-last-change and link activity summary across all ports to spot interfaces that recently bounced:<\/p>\n<pre><code class=\"language-ios\">Switch# show interfaces link\nPort       Name               Down Time          Up Time\nGi1\/0\/1    Uplink-Core        00:00:00           45d12h\nGi1\/0\/10   AP-Floor2          00:01:14           00:00:22\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Verify_If_the_Port_Was_Shut_Down_Into_an_err-disabled_State\"><\/span>Step 4: Verify If the Port Was Shut Down Into an <code>err-disabled<\/code> State<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If a port flaps rapidly beyond the switch&#8217;s threshold, Cisco&#8217;s Link Flap Prevention mechanism disables the port automatically. Check whether any interfaces are currently suspended:<\/p>\n<pre><code class=\"language-ios\">Switch# show interfaces status err-disabled\n\nPort      Name               Status       Reason               Err-disabled Vlans\nGi1\/0\/10  AP-Floor2          err-disabled link-flap\n<\/code><\/pre>\n<p>Takeaway: Correlating <code>show logging<\/code> timestamps with <code>interface resets<\/code> and <code>show interfaces status err-disabled<\/code> immediately isolates whether a port is actively flapping or has already been shut down by the switch.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Understanding_the_Causes_of_Port_Flapping_and_the_link-flap_Errdisable_State\"><\/span>Understanding the Causes of Port Flapping and the <code>link-flap<\/code> Errdisable State<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Once CLI diagnostics confirm that a physical interface is cycling up and down, identifying the underlying Layer 1 or protocol fault prevents the issue from recurring. The most common questions regarding root causes and Cisco&#8217;s automated shutdown behavior are addressed below.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_is_my_Cisco_switch_interface_going_up_and_down_repeatedly\"><\/span>Why is my Cisco switch interface going up and down repeatedly?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Physical port flapping occurs when the switch&#8217;s PHY chip repeatedly loses and regains carrier signal or link synchronization with the connected device. The primary causes include:<br \/>\n* <strong>Damaged or Substandard Ethernet Cabling:<\/strong> Broken twisted pairs, loose RJ45 crimps, oxidized patch panel punch-downs, or copper runs exceeding 100 meters cause intermittent loss of electrical continuity.<br \/>\n* <strong>Faulty or Incompatible SFP\/SFP+ Transceivers:<\/strong> Degraded laser diodes, dirty fiber end-faces, mismatched wavelengths (e.g., 850nm multimode vs. 1310nm single-mode), or uncertified third-party optics cause optical receive power to hover right at the loss-of-signal (LOS) threshold.<br \/>\n* <strong>Speed, Duplex, and Auto-Negotiation Mismatches:<\/strong> Hardcoding speed and duplex on one end while leaving the link partner set to <code>auto<\/code> frequently causes link negotiation failures, late collisions, and repeated link resets.<br \/>\n* <strong>Power over Ethernet (PoE) Overload or Brownouts:<\/strong> If a powered device (such as a pan-tilt-zoom camera or Wi-Fi 6E\/7 access point) draws more wattage than the port allows\u2014or has a short in the cable\u2014the switch cuts inline power, causing the endpoint to reboot in an endless loop.<br \/>\n* <strong>Energy Efficient Ethernet (EEE \/ 802.3az) Incompatibilities:<\/strong> Low-power idle states between certain switch ASICs and endpoint NIC drivers can fail to wake properly, dropping and re-establishing the link.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_does_a_Cisco_switch_put_a_flapping_port_into_an_err-disabled_state\"><\/span>Why does a Cisco switch put a flapping port into an <code>err-disabled<\/code> state?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Every time an interface changes state, the switch CPU must process interrupts, update hardware forwarding tables, generate syslog\/SNMP notifications, and potentially trigger Spanning Tree Protocol (STP) Topology Change Notifications (TCNs) or routing protocol reconvergence. To protect the control plane from high CPU utilization and stabilize the network topology, Cisco switches enable <strong>Link Flap Detection<\/strong> by default. When an interface exceeds the allowed number of up\/down cycles within a short measurement window, the switch places the port into an <code>err-disabled<\/code> state with the reason <code>link-flap<\/code>, logging <code>%PM-4-ERR_DISABLE: link-flap error detected on [interface], putting [interface] in err-disable state<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"How_do_I_check_the_current_link-flap_threshold_values_on_my_switch\"><\/span>How do I check the current <code>link-flap<\/code> threshold values on my switch?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Default thresholds vary slightly by platform and IOS release (commonly <strong>5 flaps within 10 seconds<\/strong> on Catalyst switches, or up to <strong>20 flaps within 10 seconds<\/strong> on certain routing platforms). Check your device&#8217;s exact thresholds and detection status with these EXEC commands:<\/p>\n<pre><code class=\"language-ios\">! View flap counts and time windows that trigger errdisable\nSwitch# show errdisable flap-values\n\nErrDisable Reason    Flaps    Time (sec)\n-----------------    ------   ----------\npagp-flap              3       30\ndtp-flap               3       30\nlink-flap              5       10\n\n! Confirm link-flap detection is enabled\nSwitch# show errdisable detect | include link-flap\n<\/code><\/pre>\n<p>Takeaway: The <code>link-flap<\/code> err-disabled state is a protective control-plane mechanism triggered almost exclusively by Layer 1 hardware faults, PoE brownouts, or negotiation mismatches.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Configuration_Templates_Link-Flap_Thresholds_Auto-Recovery_and_Interface_Dampening\"><\/span>Configuration Templates: Link-Flap Thresholds, Auto-Recovery, and Interface Dampening<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>After resolving or mitigating physical instability, you can use the following Cisco IOS \/ IOS-XE configuration templates to manually recover suspended ports, automate <code>errdisable<\/code> recovery, customize link-flap sensitivity, or apply IP event dampening on Layer 3 routed interfaces.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"1_Enable_Automatic_Errdisable_Recovery_for_Link-Flap_Events\"><\/span>1. Enable Automatic Errdisable Recovery for Link-Flap Events<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>By default, an <code>err-disabled<\/code> port stays down until an administrator intervenes. Use this template to automatically re-enable ports shut down by <code>link-flap<\/code> after a defined cooldown timer:<\/p>\n<pre><code class=\"language-ios\">configure terminal\n ! Ensure link-flap detection is active\n errdisable detect cause link-flap\n !\n ! Enable auto-recovery specifically for link-flap shutdowns\n errdisable recovery cause link-flap\n !\n ! Set recovery timer in seconds (Range: 30 to 86400; Default: 300)\n errdisable recovery interval 300\nend\n\n! Verify auto-recovery configuration and check countdown timers for active ports\nshow errdisable recovery\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"2_Customize_Link-Flap_Error_Thresholds\"><\/span>2. Customize Link-Flap Error Thresholds<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>In environments where brief link bounces are expected during endpoint boot cycles, adjust how many flaps must occur within a given window before the switch disables the port:<\/p>\n<pre><code class=\"language-ios\">configure terminal\n ! Syntax: errdisable flap-setting cause link-flap max-flaps &lt;1-100&gt; time &lt;1-120&gt;\n errdisable flap-setting cause link-flap max-flaps 10 time 15\nend\n\n! Verify updated threshold values\nshow errdisable flap-values\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"3_Manually_Reset_an_Err-Disabled_Interface_Plus_EEE_Mitigation\"><\/span>3. Manually Reset an Err-Disabled Interface (Plus EEE Mitigation)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If auto-recovery is not enabled, bounce the interface administratively after replacing the faulty cable or transceiver. If Energy Efficient Ethernet (EEE) negotiation is causing the flap, disable EEE on the port simultaneously:<\/p>\n<pre><code class=\"language-ios\">configure terminal\n interface GigabitEthernet1\/0\/10\n  ! Optional: Disable 802.3az Green Ethernet \/ EEE if NIC negotiation flaps\n  no power efficient-ethernet auto\n  ! Reset the err-disabled state\n  shutdown\n  no shutdown\nend\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"4_Configure_Interface_Event_Dampening_Routed_Layer_3_Ports\"><\/span>4. Configure Interface Event Dampening (Routed \/ Layer 3 Ports)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On Layer 3 switch interfaces or routed uplinks where a flapping link repeatedly triggers OSPF, EIGRP, or BGP route recalculations, enable <strong>IP Event Dampening<\/strong>. Each flap assigns a penalty (default <code>1000<\/code>); once the penalty exceeds the suppress threshold, the switch suppresses routing updates for that interface until the penalty decays below the reuse threshold:<\/p>\n<pre><code class=\"language-ios\">configure terminal\n interface GigabitEthernet1\/0\/48\n  no switchport\n  ! Enable dampening with default parameters:\n  ! Half-life: 5 sec | Reuse: 1000 | Suppress: 2000 | Max-suppress: 20 sec\n  dampening\n  !\n  ! Or specify custom parameters:\n  ! dampening &lt;half-life 1-30&gt; &lt;reuse 1-20000&gt; &lt;suppress 1-20000&gt; &lt;max-suppress 1-255&gt;\n  dampening 10 1000 2000 40\nend\n\n! Verify dampening status and suppressed interfaces\nshow interface dampening\nshow dampening interface\n<\/code><\/pre>\n<p>Takeaway: Use <code>errdisable recovery cause link-flap<\/code> on Layer 2 access ports for hands-off recovery, and reserve <code>dampening<\/code> for Layer 3 routed uplinks to shield dynamic routing protocols from instability.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"How_to_Check_and_Troubleshoot_Layer_2_MAC_Address_Flapping\"><\/span>How to Check and Troubleshoot Layer 2 MAC Address Flapping<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Not all flapping on a Cisco switch involves a physical port going down. <strong>MAC address flapping<\/strong> occurs when the physical links remain solidly <code>up<\/code>, but the switch&#8217;s Content Addressable Memory (CAM) table repeatedly learns the exact same source MAC address on two or more different interfaces within the same VLAN.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Identify_the_Flapping_MAC_Address_VLAN_and_Ports_in_Syslog\"><\/span>Step 1: Identify the Flapping MAC Address, VLAN, and Ports in Syslog<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When MAC flapping occurs, Cisco Catalyst switches generate <code>%SW_MATM-4-MACFLAP_NOTIF<\/code> alerts (while Cisco Nexus switches log <code>%L2FM-4-L2FM_MAC_FLAP_MOVE<\/code>). Check the logs to extract three critical pieces of data: the <strong>Host MAC address<\/strong>, the <strong>VLAN ID<\/strong>, and the <strong>two competing ports<\/strong>:<\/p>\n<pre><code class=\"language-ios\">Switch# show logging | include MACFLAP_NOTIF\nApr 26 12:27:55: %SW_MATM-4-MACFLAP_NOTIF: Host 0011.2233.4455 in vlan 10 is flapping between port Gi1\/0\/10 and port Po1\n<\/code><\/pre>\n<p>You can also enable and inspect detailed MAC move counters directly in the MAC address table notification history:<\/p>\n<pre><code class=\"language-ios\">Switch# show mac address-table notification change\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_Current_MAC_Table_Learning_and_Trace_Neighboring_Devices\"><\/span>Step 2: Check Current MAC Table Learning and Trace Neighboring Devices<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Query the MAC address table for the offending host address and identify what is connected to the two ports reported in the log:<\/p>\n<pre><code class=\"language-ios\">! Check which port currently holds the MAC entry\nSwitch# show mac address-table address 0011.2233.4455\n\n! Identify the OUI\/vendor or check ARP cache on a Layer 3 switch to find the IP\nSwitch# show ip arp | include 0011.2233.4455\n\n! Check CDP and LLDP to see if the flapping ports lead to downstream switches or APs\nSwitch# show cdp neighbors Gi1\/0\/10 detail\nSwitch# show lldp neighbors Po1 detail\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Distinguish_Benign_Host_Movement_from_Dangerous_Layer_2_Loops\"><\/span>Step 3: Distinguish Benign Host Movement from Dangerous Layer 2 Loops<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Before shutting down ports, determine which of the four common scenarios is causing the MAC flap:<br \/>\n1. <strong>Wireless Client Roaming (Benign):<\/strong> If the MAC address belongs to a Wi-Fi client and the two ports connect to wireless Access Points (in local\/flex-connect bridged mode), the flap simply reflects a user roaming between APs. Optimizing AP transmit power or cell overlap reduces excessive roaming flaps.<br \/>\n2. <strong>Server NIC Teaming \/ Virtual Switch Misconfiguration (Moderate Impact):<\/strong> If both ports connect to the same ESXi host, Hyper-V server, or Linux bond configured for active-active load balancing (such as &#8220;Route based on IP hash&#8221;) <em>without<\/em> a corresponding Port-Channel\/LACP configuration on the Cisco switch, frames from the same VM MAC will arrive on different physical ports.<br \/>\n3. <strong>EtherChannel \/ DTP Mismatch (Moderate Impact):<\/strong> Inconsistent trunking or channel-group modes (e.g., <code>mode on<\/code> on one side and LACP <code>active<\/code> on the other, or rogue DTP frame forwarding across unmanaged devices) causes traffic to loop back over parallel links. Verify bundle consistency with <code>show etherchannel summary<\/code>.<br \/>\n4. <strong>Bridging \/ Layer 2 Forwarding Loop (High Impact):<\/strong> An unmanaged desktop switch plugged into two wall jacks, a cabling loop, or a Spanning Tree failure causes broadcast and unicast frames to circulate endlessly, making every MAC address appear to flap between the looped ports.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Pinpoint_and_Break_a_Layer_2_Loop_Using_Input_Packet_Rates_and_STP_Counters\"><\/span>Step 4: Pinpoint and Break a Layer 2 Loop Using Input Packet Rates and STP Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If you suspect a Layer 2 loop, check interface input packet rates and Spanning Tree Topology Change Notification (TCN) counters:<\/p>\n<pre><code class=\"language-ios\">! Look for interfaces with abnormally high 6- to 8-digit packet\/sec input rates\nSwitch# show interfaces | include is up|input rate\n\n! Check which port is generating constant Spanning Tree topology changes\nSwitch# show spanning-tree vlan 10 detail | include ieee|occurr|from\n<\/code><\/pre>\n<p>Follow the port with the highest input packet rate to the downstream switch using CDP\/LLDP until you locate the edge port where the physical loop originates, then administratively shut down the offending interface.<\/p>\n<p>Takeaway: Always check <code>show cdp\/lldp neighbors<\/code> and <code>input rate<\/code> counters when troubleshooting <code>%SW_MATM-4-MACFLAP_NOTIF<\/code> to quickly separate harmless wireless roaming from catastrophic Layer 2 broadcast storms.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Best_Network_Monitoring_Tools_to_Detect_Cisco_Switch_Flapping_Proactively\"><\/span>Best Network Monitoring Tools to Detect Cisco Switch Flapping Proactively<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Rather than waiting for users to report dropped connections and running manual CLI commands, network administrators rely on SNMP trap receivers and Syslog analyzers to detect physical port flaps and MAC table instability in real time.<\/p>\n<ol>\n<li><strong>Cisco Catalyst Center (formerly Cisco DNA Center)<\/strong><\/li>\n<li><strong>How it detects flapping:<\/strong> Uses streaming telemetry, SNMP, and Syslog correlation alongside AI-driven network analytics to automatically flag flapping interfaces, PoE faults, SFP optical degradation, and Layer 2 MAC move anomalies across Catalyst 9000 architectures.<\/li>\n<li>\n<p><strong>Best for:<\/strong> Medium-to-large enterprise Cisco networks seeking automated root-cause analysis and guided remediation workflows.<\/p>\n<\/li>\n<li>\n<p><strong>SolarWinds Network Performance Monitor (NPM)<\/strong><\/p>\n<\/li>\n<li><strong>How it detects flapping:<\/strong> Polls Cisco interface MIBs (<code>IF-MIB<\/code>), listens for <code>linkUp<\/code>\/<code>linkDown<\/code> SNMP traps, and ingests <code>%LINK-3-UPDOWN<\/code> and <code>%SW_MATM-4-MACFLAP_NOTIF<\/code> syslogs. Administrators can configure custom alerting rules that trigger only when a port transitions more than $X$ times within $Y$ minutes.<\/li>\n<li>\n<p><strong>Best for:<\/strong> Multi-vendor enterprise NOCs requiring granular flap-rate thresholds and historical interface availability heatmaps.<\/p>\n<\/li>\n<li>\n<p><strong>PRTG Network Monitor (Paessler)<\/strong><\/p>\n<\/li>\n<li><strong>How it detects flapping:<\/strong> Combines SNMP Traffic, SNMP Trap Receiver, and Syslog Receiver sensors to monitor port state changes (<code>ifOperStatus<\/code>) and <code>err-disabled<\/code> states. Its built-in state-change counters immediately highlight ports with abnormal reset frequencies.<\/li>\n<li>\n<p><strong>Best for:<\/strong> Mid-sized IT teams looking for rapid sensor-based deployment and customizable dashboard alerts.<\/p>\n<\/li>\n<li>\n<p><strong>ManageEngine OpManager<\/strong><\/p>\n<\/li>\n<li><strong>How it detects flapping:<\/strong> Processes Cisco SNMP traps (including <code>cieLinkDown<\/code>, <code>cieLinkUp<\/code>, and <code>cmnMacChangedNotification<\/code>) and correlates Syslog events into tiered alarms, with automated workflow actions that can execute CLI scripts to inspect or shut down a misbehaving port.<\/li>\n<li>\n<p><strong>Best for:<\/strong> Organizations wanting integrated switch port mapping (Switch Port Mapper) to instantly see which endpoint MAC or IP is attached to a flapping interface.<\/p>\n<\/li>\n<li>\n<p><strong>LibreNMS + Graylog \/ ELK Stack (Open-Source Stack)<\/strong><\/p>\n<\/li>\n<li><strong>How it detects flapping:<\/strong> LibreNMS tracks interface state transitions and DOM optical transceiver power levels over SNMP, while Graylog or Elasticsearch\/Logstash\/Kibana (ELK) ingests centralized Cisco syslogs to trigger webhook alerts (Slack, PagerDuty, Teams) whenever <code>MACFLAP_NOTIF<\/code> or <code>ERR_DISABLE<\/code> strings surge in frequency.<\/li>\n<li><strong>Best for:<\/strong> Engineering teams that prefer cost-effective, open-source observability with high-speed log aggregation across hundreds of Catalyst and Nexus switches.<\/li>\n<\/ol>\n<p>Takeaway: Pairing SNMP state polling with real-time Syslog pattern matching (<code>UPDOWN<\/code>, <code>ERR_DISABLE<\/code>, and <code>MACFLAP_NOTIF<\/code>) provides immediate visibility into transient flaps before they escalate into network-wide outages.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Official_Cisco_Documentation_and_Platform_Diagnostic_References\"><\/span>Official Cisco Documentation and Platform Diagnostic References<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>This reference section outlines the official Cisco support documentation titles, platform architectures, and hardware-level diagnostic commands used to validate physical media and transceiver health on Cisco Catalyst and Cisco Nexus switches.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Official_Cisco_Support_Guides_and_Command_References\"><\/span>Official Cisco Support Guides and Command References<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Troubleshoot Port Flaps on Catalyst 9000 Series Switches (Cisco Document ID: 218219):<\/strong> Official engineering workflow covering syslog verification, copper Time-Domain Reflectometry (TDR), Digital Optical Monitoring (DOM), and Forward Error Correction (FEC) validation on Cisco IOS-XE platforms.<\/li>\n<li><strong>Troubleshoot MAC Address Flap Notification Errors (Cisco Support Article):<\/strong> Official diagnostic procedure for <code>%SW_MATM-4-MACFLAP_NOTIF<\/code>, detailing Layer 2 loop isolation via input packet rates, Spanning Tree TCN analysis, and EtherChannel consistency verification.<\/li>\n<li><strong>Errdisable Port State Recovery on the Cisco IOS Platforms (Cisco Document ID: 69980):<\/strong> Authoritative reference defining all <code>errdisable<\/code> triggers (<code>link-flap<\/code>, <code>pagp-flap<\/code>, <code>dtp-flap<\/code>, <code>udld<\/code>, <code>bpduguard<\/code>), default flap thresholds, and global recovery intervals.<\/li>\n<li><strong>Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide &amp; Show Command Reference:<\/strong> Documents NX-OS link-state tracking, <code>ethpm<\/code> (Ethernet Port Manager) internal event histories, and interface reset counters.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Platform-Specific_Hardware_Diagnostic_Commands\"><\/span>Platform-Specific Hardware Diagnostic Commands<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Diagnostic Function<\/th>\n<th style=\"text-align: left;\">Platform \/ OS<\/th>\n<th style=\"text-align: left;\">Exact CLI Command Syntax<\/th>\n<th style=\"text-align: left;\">Operational Purpose<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Copper Cable TDR Test<\/strong><\/td>\n<td style=\"text-align: left;\">Catalyst (IOS \/ IOS-XE)<\/td>\n<td style=\"text-align: left;\"><code>test cable-diagnostics tdr interface Gi1\/0\/10<\/code><br \/><code>show cable-diagnostics tdr interface Gi1\/0\/10<\/code><\/td>\n<td style=\"text-align: left;\">Sends a pulse down RJ45 copper pairs to detect open circuits, short circuits, impedance mismatches, and distance-to-fault.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Optical Transceiver DOM<\/strong><\/td>\n<td style=\"text-align: left;\">Catalyst (IOS \/ IOS-XE)<\/td>\n<td style=\"text-align: left;\"><code>show interfaces transceiver detail<\/code><\/td>\n<td style=\"text-align: left;\">Displays real-time SFP\/SFP+ laser temperature, voltage, Tx bias current, and Tx\/Rx optical power (dBm) against warning\/alarm thresholds.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Optical Transceiver DOM<\/strong><\/td>\n<td style=\"text-align: left;\">Nexus (NX-OS)<\/td>\n<td style=\"text-align: left;\"><code>show interface Eth1\/1 transceiver details<\/code><\/td>\n<td style=\"text-align: left;\">Verifies optical receive power and flags Loss of Signal (LOS) or degraded fiber paths on Nexus ports.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Internal Port State History<\/strong><\/td>\n<td style=\"text-align: left;\">Nexus (NX-OS)<\/td>\n<td style=\"text-align: left;\"><code>show system internal ethpm event-history interface Eth1\/1<\/code><\/td>\n<td style=\"text-align: left;\">Dumps the low-level NX-OS Ethernet Port Manager state machine log to trace sub-second link transitions and transceiver state changes.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Hardware Controller Counters<\/strong><\/td>\n<td style=\"text-align: left;\">Catalyst (IOS-XE)<\/td>\n<td style=\"text-align: left;\"><code>show interfaces Gi1\/0\/10 controller<\/code><\/td>\n<td style=\"text-align: left;\">Reads raw ASIC\/MAC-level transmit and receive error counters directly from switch hardware.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Takeaway: Utilizing built-in hardware diagnostics like <code>test cable-diagnostics tdr<\/code> for copper runs and <code>show interfaces transceiver detail<\/code> for fiber links eliminates guesswork when proving whether a flapping port is caused by defective physical cabling or failing optics.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Checking and resolving flapping on a Cisco switch starts with distinguishing between Layer 1 physical link instability and Layer 2 MAC address movement. By inspecting <code>show logging<\/code> and <code>show interfaces<\/code> counters first, verifying whether <code>link-flap<\/code> protection has placed ports into an <code>err-disabled<\/code> state, and validating physical media with TDR or DOM diagnostics, you can quickly stabilize bouncing physical ports and tune auto-recovery timers. When physical links are stable but <code>%SW_MATM-4-MACFLAP_NOTIF<\/code> messages appear, tracing neighbor connections and interface input rates allows you to isolate Layer 2 loops or misconfigured host bonds before they disrupt the wider network.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-flapping-in-cisco-switch_24577.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+Flapping+in+Cisco+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\",\"How to Check Flapping in Cisco Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Network instability on a Cisco switch often manifests in one of two ways: physical port (link) flapping, where an interface repeatedly cycles between up and down states, or Layer 2 MAC address flapping, where the switch continuously relearns the same hardware address across different ports. Both conditions degrade application performance, trigger Spanning Tree Protocol (STP)&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check Flapping in Cisco Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check Flapping in Cisco Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Network instability on a Cisco switch often manifests in one of two ways: physical port (link) flapping, where an interface repeatedly cycles between up and down states, or Layer 2 MAC address flapping, where the switch continuously relearns the same hardware address across different ports. Both conditions degrade application performance, trigger Spanning Tree Protocol (STP)... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T07:09:35+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"14 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\",\"name\":\"How to Check Flapping in Cisco Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T07:09:35+00:00\",\"dateModified\":\"2026-11-17T07:09:35+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check Flapping in Cisco Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check Flapping in Cisco Switch\",\"datePublished\":\"2026-11-17T07:09:35+00:00\",\"dateModified\":\"2026-11-17T07:09:35+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage\"},\"wordCount\":2228,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check Flapping in Cisco Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html","og_locale":"en_US","og_type":"article","og_title":"How to Check Flapping in Cisco Switch - SPOTO Official Blog","og_description":"Network instability on a Cisco switch often manifests in one of two ways: physical port (link) flapping, where an interface repeatedly cycles between up and down states, or Layer 2 MAC address flapping, where the switch continuously relearns the same hardware address across different ports. Both conditions degrade application performance, trigger Spanning Tree Protocol (STP)... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T07:09:35+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"14 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html","name":"How to Check Flapping in Cisco Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T07:09:35+00:00","dateModified":"2026-11-17T07:09:35+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check Flapping in Cisco Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check Flapping in Cisco Switch","datePublished":"2026-11-17T07:09:35+00:00","dateModified":"2026-11-17T07:09:35+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#webpage"},"wordCount":2228,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-flapping-in-cisco-switch_24577.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24577"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24577"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24577\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24577"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24577"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24577"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}