{"id":24569,"date":"2026-11-17T14:45:27","date_gmt":"2026-11-17T06:45:27","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html"},"modified":"2026-11-17T14:45:27","modified_gmt":"2026-11-17T06:45:27","slug":"how-to-check-config-register-in-cisco-9300-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html","title":{"rendered":"How to Check Config Register in Cisco 9300 Switch"},"content":{"rendered":"<p>When network administrators transition from legacy Cisco Catalyst platforms\u2014such as the Catalyst 2960X, 3560, or 3750\u2014to the enterprise-grade Cisco Catalyst 9300 Series, one of the first discrepancies they encounter is during routine hardware audits or password recovery workflows. Running the traditional <code>show version<\/code> command does not yield the expected hexadecimal configuration register at the bottom of the output. <\/p>\n<p>In classic Cisco IOS, the 16-bit software configuration register (such as <code>0x2102<\/code> or <code>0x2142<\/code>) governed fundamental boot behaviors, console line speeds, and whether the system loaded or bypassed NVRAM startup configurations. On modern Catalyst 9000 Series switches powered by Cisco IOS XE, this legacy register has been fully superseded. Below is everything you need to know about checking boot parameters, inspecting ROMMON variables, replacing obsolete register settings, and executing administrative recoveries on the Catalyst 9300.<\/p>\n<hr \/>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Frequently_Asked_Questions_The_Catalyst_9300_Configuration_Register\" title=\"Frequently Asked Questions: The Catalyst 9300 Configuration Register\">Frequently Asked Questions: The Catalyst 9300 Configuration Register<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Why_is_the_configuration_register_not_showing_in_Cisco_Catalyst_9300_show_version\" title=\"Why is the configuration register not showing in Cisco Catalyst 9300 show version?\">Why is the configuration register not showing in Cisco Catalyst 9300 show version?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Can_I_still_use_the_config-register_CLI_command_in_Cisco_IOS_XE\" title=\"Can I still use the config-register CLI command in Cisco IOS XE?\">Can I still use the config-register CLI command in Cisco IOS XE?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Official_Cisco_Architecture_Configuration_Register_Replacement_CLIs\" title=\"Official Cisco Architecture: Configuration Register Replacement CLIs\">Official Cisco Architecture: Configuration Register Replacement CLIs<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Classic_Cisco_IOS_vs_Cisco_IOS_XE_Boot_Settings_Comparison\" title=\"Classic Cisco IOS vs. Cisco IOS XE Boot Settings Comparison\">Classic Cisco IOS vs. Cisco IOS XE Boot Settings Comparison<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step-by-Step_Guide_How_to_Check_Boot_Variables_and_ROMMON_Settings\" title=\"Step-by-Step Guide: How to Check Boot Variables and ROMMON Settings\">Step-by-Step Guide: How to Check Boot Variables and ROMMON Settings<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_1_Inspect_System_Boot_Paths\" title=\"Step 1: Inspect System Boot Paths\">Step 1: Inspect System Boot Paths<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_2_Display_Low-Level_ROMMON_Variables_show_romvar\" title=\"Step 2: Display Low-Level ROMMON Variables (show romvar)\">Step 2: Display Low-Level ROMMON Variables (show romvar)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_3_Check_Environment_Variables_from_ROMMON_Mode\" title=\"Step 3: Check Environment Variables from ROMMON Mode\">Step 3: Check Environment Variables from ROMMON Mode<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step-by-Step_Guide_Bypassing_Startup_Configuration_for_Password_Recovery\" title=\"Step-by-Step Guide: Bypassing Startup Configuration for Password Recovery\">Step-by-Step Guide: Bypassing Startup Configuration for Password Recovery<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_1_Connect_Console_and_Interrupt_Boot\" title=\"Step 1: Connect Console and Interrupt Boot\">Step 1: Connect Console and Interrupt Boot<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_2_Set_the_Startup_Config_Ignore_Variable\" title=\"Step 2: Set the Startup Config Ignore Variable\">Step 2: Set the Startup Config Ignore Variable<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_3_Boot_Cisco_IOS_XE\" title=\"Step 3: Boot Cisco IOS XE\">Step 3: Boot Cisco IOS XE<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_4_Merge_Existing_Startup_Configuration\" title=\"Step 4: Merge Existing Startup Configuration\">Step 4: Merge Existing Startup Configuration<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_5_Configure_New_Administrative_Passwords\" title=\"Step 5: Configure New Administrative Passwords\">Step 5: Configure New Administrative Passwords<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Step_6_Reset_the_Startup-Config_Bypass_Flag_and_Save\" title=\"Step 6: Reset the Startup-Config Bypass Flag and Save\">Step 6: Reset the Startup-Config Bypass Flag and Save<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Troubleshooting_Guide_Catalyst_9300_Not_Loading_Startup_Config_After_Reload\" title=\"Troubleshooting Guide: Catalyst 9300 Not Loading Startup Config After Reload\">Troubleshooting Guide: Catalyst 9300 Not Loading Startup Config After Reload<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Cause_of_the_Issue\" title=\"Cause of the Issue\">Cause of the Issue<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Resolution_Steps\" title=\"Resolution Steps\">Resolution Steps<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Catalyst_9300_Boot_Configuration_and_ROMMON_Cheat_Sheet\" title=\"Catalyst 9300 Boot Configuration and ROMMON Cheat Sheet\">Catalyst 9300 Boot Configuration and ROMMON Cheat Sheet<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Cisco_IOS_XE_EXEC_Mode_Verification_Commands\" title=\"Cisco IOS XE EXEC Mode Verification Commands\">Cisco IOS XE EXEC Mode Verification Commands<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Cisco_IOS_XE_Global_Configuration_Commands\" title=\"Cisco IOS XE Global Configuration Commands\">Cisco IOS XE Global Configuration Commands<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#ROMMON_Mode_switch_Syntax_Template\" title=\"ROMMON Mode (switch:) Syntax Template\">ROMMON Mode (switch:) Syntax Template<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-24\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Frequently_Asked_Questions_The_Catalyst_9300_Configuration_Register\"><\/span>Frequently Asked Questions: The Catalyst 9300 Configuration Register<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3><span class=\"ez-toc-section\" id=\"Why_is_the_configuration_register_not_showing_in_Cisco_Catalyst_9300_show_version\"><\/span>Why is the configuration register not showing in Cisco Catalyst 9300 <code>show version<\/code>?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Cisco Catalyst 9300 switches run Cisco IOS XE, a modern operating system built on a Linux kernel that interacts directly with modular bootloaders rather than legacy monolithic IOS microcode. The traditional 16-bit software configuration register does not exist at a hardware or architectural level on the Catalyst 9300. <\/p>\n<p>In early Cisco IOS XE releases, a dummy configuration register value was still displayed at the bottom of <code>show version<\/code>, and the global configuration command <code>config-register<\/code> was technically accepted by the parser. However, these settings had no functional impact on the actual hardware boot process, which led to operational confusion and misconfigurations. Consequently, Cisco permanently removed the configuration register line from the <code>show version<\/code> output starting in Cisco IOS XE Everest 16.12.4 and Amsterdam 17.3.1.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Can_I_still_use_the_config-register_CLI_command_in_Cisco_IOS_XE\"><\/span>Can I still use the <code>config-register<\/code> CLI command in Cisco IOS XE?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On current IOS XE releases, the <code>config-register &lt;hex-value&gt;<\/code> command is deprecated, ineffective, or completely removed from the CLI hierarchy. Entering a command like <code>config-register 0x2142<\/code> will either return a syntax rejection or have zero effect on subsequent reloads. Boot parameters and configuration bypass flags are now handled exclusively through dedicated IOS XE CLI commands and low-level ROMMON environment variables.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Official_Cisco_Architecture_Configuration_Register_Replacement_CLIs\"><\/span>Official Cisco Architecture: Configuration Register Replacement CLIs<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Cisco outlines the architectural shift from legacy register masks to modern commands in Cisco Technical Support Documentation (Doc ID 216850: <em>&#8220;Configuration Register Equivalent CLIs in Cisco IOS XE&#8221;<\/em>). <\/p>\n<p>Under legacy Cisco IOS, administrators manipulated specific bit positions inside a 16-bit hexadecimal word:<br \/>\n* <strong>Bits 0\u20133 (Boot Field):<\/strong> Determined whether the device dropped to ROMMON (<code>0x0<\/code>), booted a bootloader helper image (<code>0x1<\/code>), or parsed boot system parameters from NVRAM (<code>0x2<\/code>\u2013<code>0xF<\/code>).<br \/>\n* <strong>Bit 6 (Ignore NVRAM):<\/strong> Instructed the bootloader to ignore the startup configuration stored in NVRAM (commonly <code>0x2142<\/code> during password recovery).<br \/>\n* <strong>Bit 8 (Break Disable):<\/strong> Controlled console break key capability during the initial boot sequence.<br \/>\n* <strong>Bits 5, 11, and 12 (Console Speed):<\/strong> Defined console port baud rates ranging from 1200 bps up to 115200 bps.<\/p>\n<p>In Cisco IOS XE on Catalyst 9000 Series switches, bitmask registers are replaced by explicit, human-readable CLI commands in Cisco IOS XE EXEC and Global Configuration modes. These commands write discrete key-value pairs directly to non-volatile flash environment variables (ROMMON variables). Rather than interpreting a cryptographic-like hex value, the bootloader evaluates explicit environment flags, such as <code>MANUAL_BOOT<\/code>, <code>ENABLE_BREAK<\/code>, and <code>SWITCH_IGNORE_STARTUP_CFG<\/code>.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Classic_Cisco_IOS_vs_Cisco_IOS_XE_Boot_Settings_Comparison\"><\/span>Classic Cisco IOS vs. Cisco IOS XE Boot Settings Comparison<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The following table maps classic Cisco IOS configuration register values directly to their modern Cisco IOS XE command equivalents and underlying ROMMON variables on Catalyst 9300 switches:<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Desired Switch Behavior<\/th>\n<th style=\"text-align: left;\">Classic Cisco IOS Hex Value<\/th>\n<th style=\"text-align: left;\">Modern Cisco IOS XE Command<\/th>\n<th style=\"text-align: left;\">Active ROMMON Variable<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Boot Normally from Flash<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x2102<\/code> \/ <code>0x102<\/code><\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# no boot manual<\/code><\/td>\n<td style=\"text-align: left;\"><code>MANUAL_BOOT=no<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Stop at ROMMON Prompt on Reload<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x0<\/code> \/ <code>0x2120<\/code><\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# boot manual<\/code><\/td>\n<td style=\"text-align: left;\"><code>MANUAL_BOOT=yes<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Bypass Startup Configuration<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x2142<\/code><\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# system ignore startupconfig switch all<\/code><\/td>\n<td style=\"text-align: left;\"><code>SWITCH_IGNORE_STARTUP_CFG=1<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Load Startup Configuration Normally<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x2102<\/code><\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# no system ignore startupconfig switch all<\/code><\/td>\n<td style=\"text-align: left;\"><code>SWITCH_IGNORE_STARTUP_CFG=0<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Enable Console Break Signal<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x2102<\/code> (Bit 8 unset)<\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# boot enable-break<\/code><\/td>\n<td style=\"text-align: left;\"><code>ENABLE_BREAK=yes<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Disable Console Break Signal<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x2002<\/code> (Bit 8 set)<\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# no boot enable-break<\/code><\/td>\n<td style=\"text-align: left;\"><code>ENABLE_BREAK=no<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Change Console Baud Rate (e.g., 115200)<\/strong><\/td>\n<td style=\"text-align: left;\"><code>0x3922<\/code><\/td>\n<td style=\"text-align: left;\"><code>Switch(config-line)# speed 115200<\/code><\/td>\n<td style=\"text-align: left;\"><code>BAUD=115200<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Disable Standard Password Recovery<\/strong><\/td>\n<td style=\"text-align: left;\"><code>service password-recovery<\/code> disabled<\/td>\n<td style=\"text-align: left;\"><code>Switch(config)# system disable password recovery switch all<\/code><\/td>\n<td style=\"text-align: left;\"><code>SWITCH_DISABLE_PASSWORD_RECOVERY=1<\/code><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_Guide_How_to_Check_Boot_Variables_and_ROMMON_Settings\"><\/span>Step-by-Step Guide: How to Check Boot Variables and ROMMON Settings<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Because <code>show version<\/code> no longer presents configuration register state, switch administrators must use specific verification commands in Cisco IOS XE or directly within ROMMON.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Inspect_System_Boot_Paths\"><\/span>Step 1: Inspect System Boot Paths<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To check which software image the switch is scheduled to load, run the <code>show boot<\/code> command from privileged EXEC mode:<\/p>\n<pre><code class=\"language-text\">Switch# show boot\n---------------------------\nSwitch 1\n---------------------------\nCurrent Boot Variables:\nBOOT variable = flash:packages.conf;\nConfiguration Register Variable = 0x102\n\nBoot Variables on next reload:\nBOOT variable = flash:packages.conf;\nManual Boot = no\nEnable Break = yes\nBoot Mode = DEVICE\niPXE Timeout = 0\n<\/code><\/pre>\n<p><em>Note: While legacy field labels like &#8220;Configuration Register Variable&#8221; may still linger as residual cosmetic artifacts on certain firmware builds, the actionable parameters are <code>BOOT variable<\/code>, <code>Manual Boot<\/code>, and <code>Enable Break<\/code>.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Display_Low-Level_ROMMON_Variables_show_romvar\"><\/span>Step 2: Display Low-Level ROMMON Variables (<code>show romvar<\/code>)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The authoritative command to verify all underlying boot variables on a Catalyst 9300 is <code>show romvar<\/code>:<\/p>\n<pre><code class=\"language-text\">Switch# show romvar\nROMMON variables:\n SWITCH_NUMBER = 1\n BOARD_REVISION = 5\n MOTHERBOARD_SERIAL_NUM = FOC23000000\n MODEL_NUM = C9300-48P\n SYSTEM_SERIAL_NUM = FOC23000000\n MAC_ADDR = 70:69:79:00:11:22\n MANUAL_BOOT = no\n ENABLE_BREAK = yes\n SWITCH_IGNORE_STARTUP_CFG = 0\n BAUD = 9600\n BPF_REV = 1\n RET_2_RTS = \n BOOT = flash:packages.conf;\n<\/code><\/pre>\n<p>This output confirms the active operational parameters. If <code>SWITCH_IGNORE_STARTUP_CFG<\/code> is set to <code>0<\/code>, the switch will load the saved startup configuration upon reboot.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Check_Environment_Variables_from_ROMMON_Mode\"><\/span>Step 3: Check Environment Variables from ROMMON Mode<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If the switch is halted at the <code>switch:<\/code> bootloader prompt, view the same variables using the <code>set<\/code> command:<\/p>\n<pre><code class=\"language-text\">switch: set\nBAUD=9600\nBOOT=flash:packages.conf;\nENABLE_BREAK=yes\nMANUAL_BOOT=no\nMODEL_NUM=C9300-48P\nSWITCH_IGNORE_STARTUP_CFG=0\nSWITCH_NUMBER=1\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_Guide_Bypassing_Startup_Configuration_for_Password_Recovery\"><\/span>Step-by-Step Guide: Bypassing Startup Configuration for Password Recovery<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>On classic Cisco switches, password recovery required changing the register to <code>0x2142<\/code>. On a Catalyst 9300, password recovery is completed by manipulating the <code>SWITCH_IGNORE_STARTUP_CFG<\/code> variable in the bootloader.<\/p>\n<pre><code>+------------------------------------+\n| 1. Connect Console &amp; Power Cycle   |\n+------------------------------------+\n                  |\n                  v\n+------------------------------------+\n| 2. Hold Mode Button -&gt; switch:     |\n+------------------------------------+\n                  |\n                  v\n+------------------------------------+\n| 3. SWITCH_IGNORE_STARTUP_CFG=1     |\n|    boot flash:packages.conf        |\n+------------------------------------+\n                  |\n                  v\n+------------------------------------+\n| 4. copy startup-config running-cfg |\n+------------------------------------+\n                  |\n                  v\n+------------------------------------+\n| 5. Reset Admin Credentials         |\n+------------------------------------+\n                  |\n                  v\n+------------------------------------+\n| 6. no system ignore startupconfig  |\n|    write memory                    |\n+------------------------------------+\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Connect_Console_and_Interrupt_Boot\"><\/span>Step 1: Connect Console and Interrupt Boot<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ol>\n<li>Attach a rollover console cable (9600-8-N-1) to the console port.<\/li>\n<li>Power cycle the switch.<\/li>\n<li>As the switch initiates bootstrap, press and hold the physical <strong>Mode<\/strong> button on the front panel. Release it after approximately 10\u201312 seconds once the <code>SYST<\/code> LED transitions from amber to blinking green\/amber, dropping the console to the <code>switch:<\/code> prompt.<\/li>\n<\/ol>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Set_the_Startup_Config_Ignore_Variable\"><\/span>Step 2: Set the Startup Config Ignore Variable<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>At the bootloader prompt, define the environment flag to bypass NVRAM:<\/p>\n<pre><code class=\"language-text\">switch: SWITCH_IGNORE_STARTUP_CFG=1\n<\/code><\/pre>\n<p><em>Note: Bootloader commands and variable names in ROMMON are strictly case-sensitive.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Boot_Cisco_IOS_XE\"><\/span>Step 3: Boot Cisco IOS XE<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Identify and boot the installed system image. For standard install-mode deployments:<\/p>\n<pre><code class=\"language-text\">switch: boot flash:packages.conf\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Merge_Existing_Startup_Configuration\"><\/span>Step 4: Merge Existing Startup Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Once the switch finishes initialization, it bypasses NVRAM and opens the unconfigured prompt without asking for a password. Do <strong>not<\/strong> enter initial setup mode.<\/p>\n<pre><code class=\"language-text\">Switch&gt; enable\nSwitch# copy startup-config running-config\n<\/code><\/pre>\n<p><em>Warning: You must copy <code>startup-config<\/code> into <code>running-config<\/code>. Reversing this command will overwrite your entire saved network configuration with an empty file.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Configure_New_Administrative_Passwords\"><\/span>Step 5: Configure New Administrative Passwords<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Re-establish local authentication credentials:<\/p>\n<pre><code class=\"language-text\">Switch# configure terminal\nSwitch(config)# enable secret &lt;NEW_SECURE_PASSWORD&gt;\nSwitch(config)# username admin privilege 15 secret &lt;NEW_ADMIN_PASSWORD&gt;\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_6_Reset_the_Startup-Config_Bypass_Flag_and_Save\"><\/span>Step 6: Reset the Startup-Config Bypass Flag and Save<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>As covered in the comparison architecture above, you must return the bypass variable to normal operation before rebooting:<\/p>\n<pre><code class=\"language-text\">Switch(config)# no system ignore startupconfig switch all\nSwitch(config)# end\nSwitch# copy running-config startup-config\n<\/code><\/pre>\n<p>Verify that <code>SWITCH_IGNORE_STARTUP_CFG<\/code> reads <code>0<\/code> via <code>show romvar<\/code> before conducting any further reboots.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Troubleshooting_Guide_Catalyst_9300_Not_Loading_Startup_Config_After_Reload\"><\/span>Troubleshooting Guide: Catalyst 9300 Not Loading Startup Config After Reload<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>A recurring issue on Catalyst 9300 switches is a unit that continuously reverts to the Initial Configuration Dialog (<code>Would you like to enter the initial configuration dialog? [yes\/no]:<\/code>) every time it reboots, despite administrators issuing <code>write memory<\/code> or <code>copy running-config startup-config<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Cause_of_the_Issue\"><\/span>Cause of the Issue<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>This behavior occurs when the switch underwent prior password recovery or staging, and the administrator neglected to clear the <code>SWITCH_IGNORE_STARTUP_CFG<\/code> variable. The switch continues to write valid configurations to <code>flash:startup-config<\/code>, but on every subsequent boot, the bootloader honors the active variable and deliberately skips NVRAM parsing.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Resolution_Steps\"><\/span>Resolution Steps<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<h4>Method A: Remediation from Cisco IOS XE (Recommended)<\/h4>\n<p>If you can access privileged EXEC mode on the switch:<\/p>\n<ol>\n<li>Check current ROMMON variables to verify the culprit:<br \/>\n   <code>text<br \/>\n   Switch# show romvar | include SWITCH_IGNORE_STARTUP_CFG<br \/>\n    SWITCH_IGNORE_STARTUP_CFG = 1<\/code><\/li>\n<li>Enter global configuration mode and clear the variable across all stack members:<br \/>\n   <code>text<br \/>\n   Switch# configure terminal<br \/>\n   Switch(config)# no system ignore startupconfig switch all<br \/>\n   Switch(config)# end<\/code><\/li>\n<li>Commit the changes to NVRAM:<br \/>\n   <code>text<br \/>\n   Switch# write memory<\/code><\/li>\n<li>Confirm the variable has flipped to <code>0<\/code>:<br \/>\n   <code>text<br \/>\n   Switch# show romvar | include SWITCH_IGNORE_STARTUP_CFG<br \/>\n    SWITCH_IGNORE_STARTUP_CFG = 0<\/code><\/li>\n<\/ol>\n<h4>Method B: Remediation from ROMMON Mode<\/h4>\n<p>If the switch cannot boot into an operable configuration or is stuck in an administrative loop:<\/p>\n<ol>\n<li>Interrupt boot via the <strong>Mode<\/strong> button to reach the <code>switch:<\/code> prompt.<\/li>\n<li>Check active variables using <code>set<\/code>:<br \/>\n   <code>text<br \/>\n   switch: set<\/code><\/li>\n<li>Clear the ignore variable explicitly:<br \/>\n   <code>text<br \/>\n   switch: unset SWITCH_IGNORE_STARTUP_CFG<\/code><br \/>\n   <em>(Alternatively: <code>switch: SWITCH_IGNORE_STARTUP_CFG=0<\/code>)<\/em><\/li>\n<li>Boot the switch:<br \/>\n   <code>text<br \/>\n   switch: boot flash:packages.conf<\/code><\/li>\n<li>Once loaded, re-save your running configuration using <code>write memory<\/code>.<\/li>\n<\/ol>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Catalyst_9300_Boot_Configuration_and_ROMMON_Cheat_Sheet\"><\/span>Catalyst 9300 Boot Configuration and ROMMON Cheat Sheet<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Use this reference template for day-to-day administrative checks, register-replacement tasks, and boot variable auditing.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Cisco_IOS_XE_EXEC_Mode_Verification_Commands\"><\/span>Cisco IOS XE EXEC Mode Verification Commands<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">! Verify software version and active package bundle\nshow version\n\n! Verify current and next-reload boot paths and break status\nshow boot\n\n! View low-level ROMMON environment variables (replaces config-register check)\nshow romvar\n\n! Inspect active console baud rate and line parameters\nshow running-config | section line con 0\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Cisco_IOS_XE_Global_Configuration_Commands\"><\/span>Cisco IOS XE Global Configuration Commands<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">configure terminal\n\n! Set switch to boot normally (Equivalent to 0x2102)\nno boot manual\n\n! Force switch to halt at ROMMON prompt on reboot (Equivalent to 0x2120 \/ 0x0)\nboot manual\n\n! Set startup-config bypass on next reload (Equivalent to 0x2142)\nsystem ignore startupconfig switch all\n\n! Restore normal startup-config parsing on next reload (Clear 0x2142)\nno system ignore startupconfig switch all\n\n! Enable\/Disable console break key during bootstrap\nboot enable-break\nno boot enable-break\n\n! Set primary boot image path\nboot system flash:packages.conf\n\nend\nwrite memory\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"ROMMON_Mode_switch_Syntax_Template\"><\/span>ROMMON Mode (<code>switch:<\/code>) Syntax Template<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">! List all active environment variables\nset\n\n! Ignore startup configuration for password recovery\nSWITCH_IGNORE_STARTUP_CFG=1\n\n! Re-enable startup configuration loading from ROMMON\nSWITCH_IGNORE_STARTUP_CFG=0\n! or\nunset SWITCH_IGNORE_STARTUP_CFG\n\n! Set or disable manual boot\nMANUAL_BOOT=0\n! or\nunset MANUAL_BOOT\n\n! Manually trigger boot sequence using installed packages\nboot flash:packages.conf\n\n! Recover from USB drive in emergency mode\nboot usbflash0:cat9k_iosxe.&lt;version&gt;.SPA.bin\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The omission of the configuration register from the Cisco Catalyst 9300 <code>show version<\/code> output represents a permanent architectural evolution in Cisco IOS XE. Hexadecimal bitmasks have been replaced by explicit, readable CLI commands and persistent ROMMON variables. By replacing outdated <code>config-register<\/code> habits with modern commands like <code>show romvar<\/code>, <code>show boot<\/code>, and <code>no system ignore startupconfig switch all<\/code>, network engineers can accurately verify boot paths, execute seamless password recoveries, and prevent persistent startup configuration loading failures.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-config-register-in-cisco-9300-switch_24569.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+Config+Register+in+Cisco+9300+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\",\"How to Check Config Register in Cisco 9300 Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>When network administrators transition from legacy Cisco Catalyst platforms\u2014such as the Catalyst 2960X, 3560, or 3750\u2014to the enterprise-grade Cisco Catalyst 9300 Series, one of the first discrepancies they encounter is during routine hardware audits or password recovery workflows. Running the traditional show version command does not yield the expected hexadecimal configuration register at the bottom&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"When network administrators transition from legacy Cisco Catalyst platforms\u2014such as the Catalyst 2960X, 3560, or 3750\u2014to the enterprise-grade Cisco Catalyst 9300 Series, one of the first discrepancies they encounter is during routine hardware audits or password recovery workflows. Running the traditional show version command does not yield the expected hexadecimal configuration register at the bottom... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T06:45:27+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\",\"name\":\"How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-17T06:45:27+00:00\",\"dateModified\":\"2026-11-17T06:45:27+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check Config Register in Cisco 9300 Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check Config Register in Cisco 9300 Switch\",\"datePublished\":\"2026-11-17T06:45:27+00:00\",\"dateModified\":\"2026-11-17T06:45:27+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage\"},\"wordCount\":1250,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html","og_locale":"en_US","og_type":"article","og_title":"How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog","og_description":"When network administrators transition from legacy Cisco Catalyst platforms\u2014such as the Catalyst 2960X, 3560, or 3750\u2014to the enterprise-grade Cisco Catalyst 9300 Series, one of the first discrepancies they encounter is during routine hardware audits or password recovery workflows. Running the traditional show version command does not yield the expected hexadecimal configuration register at the bottom... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-17T06:45:27+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"9 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html","name":"How to Check Config Register in Cisco 9300 Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-17T06:45:27+00:00","dateModified":"2026-11-17T06:45:27+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check Config Register in Cisco 9300 Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check Config Register in Cisco 9300 Switch","datePublished":"2026-11-17T06:45:27+00:00","dateModified":"2026-11-17T06:45:27+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#webpage"},"wordCount":1250,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-config-register-in-cisco-9300-switch_24569.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24569"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24569"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24569\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24569"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24569"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24569"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}