{"id":24521,"date":"2026-11-16T11:54:15","date_gmt":"2026-11-16T03:54:15","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html"},"modified":"2026-11-16T11:54:15","modified_gmt":"2026-11-16T03:54:15","slug":"how-to-check-broadcast-storm-in-cisco-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html","title":{"rendered":"How to Check Broadcast Storm in Cisco Switch"},"content":{"rendered":"<p>A broadcast storm is one of the most disruptive events that can strike a local area network. When Layer 2 broadcast or multicast frames replicate uncontrollably across a switching domain, available link bandwidth vanishes within seconds. Network latency surges, endpoints lose connectivity as ARP and DHCP packets fail to resolve, and switch control planes become unresponsive under crushing CPU load. For network engineers operating Cisco Catalyst and Nexus switches, rapidly detecting a storm, locating its origin, and enforcing automated mitigation is critical to protecting enterprise uptime.<\/p>\n<p>This operational guide provides the complete diagnostic framework for identifying, tracing, and resolving broadcast storms in Cisco switching environments, moving from symptom recognition to deep-dive CLI commands, isolation workflows, official syntax references, ready-to-deploy templates, and proactive monitoring tool comparisons.<\/p>\n<hr \/>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Broadcast_Storms_Symptoms_Triggers_and_Common_Causes\" title=\"Broadcast Storms: Symptoms, Triggers, and Common Causes\">Broadcast Storms: Symptoms, Triggers, and Common Causes<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#What_visible_symptoms_indicate_that_a_Cisco_switch_is_experiencing_a_broadcast_storm\" title=\"What visible symptoms indicate that a Cisco switch is experiencing a broadcast storm?\">What visible symptoms indicate that a Cisco switch is experiencing a broadcast storm?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#What_are_the_primary_root_causes_of_broadcast_storms_in_enterprise_networks\" title=\"What are the primary root causes of broadcast storms in enterprise networks?\">What are the primary root causes of broadcast storms in enterprise networks?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Why_doesnt_standard_Spanning_Tree_Protocol_stop_all_broadcast_storms\" title=\"Why doesn&#8217;t standard Spanning Tree Protocol stop all broadcast storms?\">Why doesn&#8217;t standard Spanning Tree Protocol stop all broadcast storms?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#How_does_a_broadcast_storm_affect_the_switch_CPU_versus_hardware_ASICs\" title=\"How does a broadcast storm affect the switch CPU versus hardware ASICs?\">How does a broadcast storm affect the switch CPU versus hardware ASICs?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Cisco_CLI_Show_Commands_to_Detect_and_Verify_a_Broadcast_Storm\" title=\"Cisco CLI Show Commands to Detect and Verify a Broadcast Storm\">Cisco CLI Show Commands to Detect and Verify a Broadcast Storm<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_1_Evaluate_Central_Processing_Unit_Utilization\" title=\"Step 1: Evaluate Central Processing Unit Utilization\">Step 1: Evaluate Central Processing Unit Utilization<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_2_Survey_Broadcast_Counts_Across_All_Operational_Ports\" title=\"Step 2: Survey Broadcast Counts Across All Operational Ports\">Step 2: Survey Broadcast Counts Across All Operational Ports<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_3_Inspect_Real-Time_Broadcast_Rates_with_Counter_Clears\" title=\"Step 3: Inspect Real-Time Broadcast Rates with Counter Clears\">Step 3: Inspect Real-Time Broadcast Rates with Counter Clears<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_4_Verify_Hardware_Storm_Control_Counters\" title=\"Step 4: Verify Hardware Storm Control Counters\">Step 4: Verify Hardware Storm Control Counters<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Methodical_Workflow_Pinpointing_and_Isolating_the_Rogue_Switch_Port\" title=\"Methodical Workflow: Pinpointing and Isolating the Rogue Switch Port\">Methodical Workflow: Pinpointing and Isolating the Rogue Switch Port<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_1_Differentiate_Ingress_from_Egress_Broadcast_Counters\" title=\"Step 1: Differentiate Ingress from Egress Broadcast Counters\">Step 1: Differentiate Ingress from Egress Broadcast Counters<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_2_Check_for_MAC_Flapping_and_STP_Topology_Changes\" title=\"Step 2: Check for MAC Flapping and STP Topology Changes\">Step 2: Check for MAC Flapping and STP Topology Changes<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_3_Trace_Downstream_Infrastructure_via_CDP_and_LLDP\" title=\"Step 3: Trace Downstream Infrastructure via CDP and LLDP\">Step 3: Trace Downstream Infrastructure via CDP and LLDP<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_4_Capture_Ingress_Traffic_Using_Local_SPAN\" title=\"Step 4: Capture Ingress Traffic Using Local SPAN\">Step 4: Capture Ingress Traffic Using Local SPAN<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Step_5_Execute_Containment_and_Administrative_Shutdown\" title=\"Step 5: Execute Containment and Administrative Shutdown\">Step 5: Execute Containment and Administrative Shutdown<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Cisco_Catalyst_and_NX-OS_Storm_Control_Architecture_and_Reference\" title=\"Cisco Catalyst and NX-OS Storm Control Architecture and Reference\">Cisco Catalyst and NX-OS Storm Control Architecture and Reference<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Architectural_Overview\" title=\"Architectural Overview\">Architectural Overview<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Cisco_IOS_IOS-XE_vs_NX-OS_Command_Reference\" title=\"Cisco IOS \/ IOS-XE vs. NX-OS Command Reference\">Cisco IOS \/ IOS-XE vs. NX-OS Command Reference<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Platform_Caveats_and_Operational_Constraints\" title=\"Platform Caveats and Operational Constraints\">Platform Caveats and Operational Constraints<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Production-Ready_Cisco_Storm_Control_Configuration_Template\" title=\"Production-Ready Cisco Storm Control Configuration Template\">Production-Ready Cisco Storm Control Configuration Template<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Comparative_Analysis_Network_Monitoring_and_Packet_Inspection_Tools\" title=\"Comparative Analysis: Network Monitoring and Packet Inspection Tools\">Comparative Analysis: Network Monitoring and Packet Inspection Tools<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Essential_Wireshark_Display_and_Capture_Filters\" title=\"Essential Wireshark Display and Capture Filters\">Essential Wireshark Display and Capture Filters<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-24\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Broadcast_Storms_Symptoms_Triggers_and_Common_Causes\"><\/span>Broadcast Storms: Symptoms, Triggers, and Common Causes<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3><span class=\"ez-toc-section\" id=\"What_visible_symptoms_indicate_that_a_Cisco_switch_is_experiencing_a_broadcast_storm\"><\/span>What visible symptoms indicate that a Cisco switch is experiencing a broadcast storm?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Physical Interface Activity:<\/strong> All port link\/activity LEDs blink simultaneously at an abnormally rapid, continuous rate (often appearing as solid illumination rather than intermittent flickering).<\/li>\n<li><strong>Console and Management Latency:<\/strong> SSH and console sessions become sluggish, drop keystrokes, or refuse new VTY connections due to control-plane CPU starvation.<\/li>\n<li><strong>Network-Wide Service Failures:<\/strong> Hosts across the VLAN experience widespread packet loss, high round-trip ping times, intermittent default gateway reachability, and failed DHCP lease renewals or ARP resolution.<\/li>\n<li><strong>Interface Counter Spikes:<\/strong> Interfaces report millions of broadcast frames received per second, accompanied by rapid increments in input discards and buffer overrun errors.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"What_are_the_primary_root_causes_of_broadcast_storms_in_enterprise_networks\"><\/span>What are the primary root causes of broadcast storms in enterprise networks?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Layer 2 Bridging Loops:<\/strong> Redundant physical connections between switches where Spanning Tree Protocol (STP) has been disabled, misconfigured, or prevented from converging due to unidirectional link failures or blocked BPDU transmission.<\/li>\n<li><strong>Rogue Unmanaged Switches and Hubs:<\/strong> Users connecting unmanaged consumer desktop switches or dumb hubs with redundant loops into wall jacks, bypassing enterprise STP boundaries.<\/li>\n<li><strong>Faulty Network Interface Cards (NICs):<\/strong> Malfunctioning client hardware, babbling transceivers, or corrupted driver stacks that continuously flood the physical medium with Layer 2 broadcast frames regardless of network state.<\/li>\n<li><strong>Virtualization Misconfigurations:<\/strong> Misconfigured virtual switches (such as VMware vSwitch or Hyper-V virtual network adapters) bridging physical NICs without loop-prevention safeguards enabled.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Why_doesnt_standard_Spanning_Tree_Protocol_stop_all_broadcast_storms\"><\/span>Why doesn&#8217;t standard Spanning Tree Protocol stop all broadcast storms?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>While STP successfully eliminates architectural Layer 2 loops between switches, it only regulates forwarding topologies\u2014it does not regulate traffic volume. If an end host on an edge access port malfunctions and emits a barrage of hundreds of thousands of broadcast frames per second, STP correctly leaves the port in the forwarding state because no switching loop exists. The switch must forward those broadcasts out of every other port in the broadcast domain, creating a severe broadcast storm that STP cannot mitigate.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"How_does_a_broadcast_storm_affect_the_switch_CPU_versus_hardware_ASICs\"><\/span>How does a broadcast storm affect the switch CPU versus hardware ASICs?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Modern Cisco switches forward normal Layer 2 data-plane traffic through specialized Application-Specific Integrated Circuits (ASICs) without involving the main CPU. However, broadcast frames (such as ARP requests) require CPU evaluation to determine if the switch&#8217;s local management IP is the target. When millions of broadcast frames enter the switch, the central processor is overwhelmed with packet-handling interrupts, exhausting CPU capacity and starving management and protocol operations (such as OSPF, BFD, and STP hello packets).<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_CLI_Show_Commands_to_Detect_and_Verify_a_Broadcast_Storm\"><\/span>Cisco CLI Show Commands to Detect and Verify a Broadcast Storm<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Once symptoms appear, verifying that high broadcast volume is the active failure mode requires querying the switch&#8217;s internal state. The following sequence of Cisco IOS \/ IOS-XE privileged EXEC commands methodically evaluates control-plane health, aggregate interface rates, and traffic counters.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Evaluate_Central_Processing_Unit_Utilization\"><\/span>Step 1: Evaluate Central Processing Unit Utilization<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Determine whether broadcast traffic has flooded the switch&#8217;s control plane by examining CPU load and interrupt levels:<\/p>\n<pre><code class=\"language-text\">Switch# show processes cpu sorted | exclude 0.00%\n<\/code><\/pre>\n<p>Look at the header line:<\/p>\n<pre><code class=\"language-text\">CPU utilization for five seconds: 98%\/89%; one minute: 92%; five minutes: 85%\n<\/code><\/pre>\n<p>A high second percentage (e.g., <code>89%<\/code>) indicates that interrupts are consuming CPU capacity. High interrupt percentages during a network slowdown strongly indicate that the processor is swamped by inbound broadcast or multicast frames.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Survey_Broadcast_Counts_Across_All_Operational_Ports\"><\/span>Step 2: Survey Broadcast Counts Across All Operational Ports<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To quickly spot which interfaces are processing abnormal broadcast volumes across the chassis, run an aggregated interface filter:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces | include (is up|broadcasts)\n<\/code><\/pre>\n<p><strong>Example Output:<\/strong><\/p>\n<pre><code class=\"language-text\">GigabitEthernet1\/0\/1 is up, line protocol is up (connected)\n     128947210 broadcasts (1209341 multicasts), 0 runts, 0 giants\nGigabitEthernet1\/0\/2 is up, line protocol is up (connected)\n     412 broadcasts (89 multicasts), 0 runts, 0 giants\nGigabitEthernet1\/0\/3 is up, line protocol is up (connected)\n     388 broadcasts (72 multicasts), 0 runts, 0 giants\n<\/code><\/pre>\n<p>In this output, <code>GigabitEthernet1\/0\/1<\/code> has accumulated over 128 million broadcasts, flagging it immediately for detailed scrutiny.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Inspect_Real-Time_Broadcast_Rates_with_Counter_Clears\"><\/span>Step 3: Inspect Real-Time Broadcast Rates with Counter Clears<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Interface broadcast numbers in <code>show interfaces<\/code> represent cumulative counters since the last reload or interface clear. To inspect real-time packet generation, clear counters on suspect ports and observe the delta over 5 to 10 seconds:<\/p>\n<pre><code class=\"language-text\">Switch# clear counters GigabitEthernet1\/0\/1\nClear &quot;show interface&quot; counters on this interface [confirm] &lt;Enter&gt;\nSwitch# show interfaces GigabitEthernet1\/0\/1 counters\n<\/code><\/pre>\n<p>Alternatively, review the instantaneous 5-minute input rate:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces GigabitEthernet1\/0\/1 | include rate\n  5 minute input rate 84210000 bits\/sec, 94210 packets\/sec\n  5 minute output rate 1200 bits\/sec, 2 packets\/sec\n<\/code><\/pre>\n<p>An input packet rate exceeding tens of thousands of packets per second with negligible output rate signals an ingress flooding condition.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Verify_Hardware_Storm_Control_Counters\"><\/span>Step 4: Verify Hardware Storm Control Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If traffic storm control is configured on the switch, query the feature&#8217;s status to confirm whether suppression thresholds have been tripped:<\/p>\n<pre><code class=\"language-text\">Switch# show storm-control broadcast\n<\/code><\/pre>\n<p><strong>Example Output:<\/strong><\/p>\n<pre><code class=\"language-text\">Interface  Filter State   Trap   Upper        Lower        Current Rate\n---------  -------------  -----  -----------  -----------  ------------\nGi1\/0\/1    Blocking       On     20.00%       15.00%       42.18%\nGi1\/0\/2    Forwarding     Off    20.00%       15.00%       0.02%\nGi1\/0\/3    Forwarding     Off    20.00%       15.00%       0.01%\n<\/code><\/pre>\n<p>A <code>Blocking<\/code> filter state verifies that ingress broadcast bandwidth surpassed the upper threshold and the switch ASIC is discarding excessive traffic.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Methodical_Workflow_Pinpointing_and_Isolating_the_Rogue_Switch_Port\"><\/span>Methodical Workflow: Pinpointing and Isolating the Rogue Switch Port<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Confirming the existence of excessive broadcast traffic is only half the battle; isolating the exact physical port originating the storm is necessary to eliminate the disruption. Because switches flood broadcast frames out of every port in a VLAN, examining a single arbitrary port will show high broadcast counts regardless of where the storm originated. Follow this systematic workflow to find the true source.<\/p>\n<pre><code>+-------------------------------------------------------------+\n| Step 1: Distinguish Ingress vs. Egress Broadcast Counters   |\n| (Identify which port is receiving, rather than forwarding)  |\n+------------------------------+------------------------------+\n                               |\n                               v\n+-------------------------------------------------------------+\n| Step 2: Check for MAC Flapping and STP Topology Changes     |\n| (Determine if the storm is a physical loop or a single host)|\n+------------------------------+------------------------------+\n                               |\n                               v\n+-------------------------------------------------------------+\n| Step 3: Trace Downstream Infrastructure via CDP \/ LLDP      |\n| (Ascertain whether the port leads to an endpoint or switch) |\n+------------------------------+------------------------------+\n                               |\n                               v\n+-------------------------------------------------------------+\n| Step 4: Capture Frame Headers Using Local SPAN              |\n| (Extract source MAC, EtherType, and protocol signatures)    |\n+------------------------------+------------------------------+\n                               |\n                               v\n+-------------------------------------------------------------+\n| Step 5: Execute Containment and Administrative Shutdown     |\n| (Disable the interface and inspect downstream hardware)     |\n+-------------------------------------------------------------+\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Differentiate_Ingress_from_Egress_Broadcast_Counters\"><\/span>Step 1: Differentiate Ingress from Egress Broadcast Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>During a storm, every port participating in the affected VLAN forwards high broadcast counts on <strong>egress<\/strong>. However, only the port connected to the offending host or loop source will show massive counts on <strong>ingress<\/strong>.<\/p>\n<p>Execute the following command to review packet directions:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces counters\n<\/code><\/pre>\n<p>Sort through the columns for <code>InBroadcastPkts<\/code> versus <code>OutBroadcastPkts<\/code>:<br \/>\n* Normal access ports: Low <code>InBroadcastPkts<\/code>, high <code>OutBroadcastPkts<\/code>.<br \/>\n* <strong>Rogue source port:<\/strong> Skyrocketing <code>InBroadcastPkts<\/code> accompanied by low or standard <code>OutBroadcastPkts<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Check_for_MAC_Flapping_and_STP_Topology_Changes\"><\/span>Step 2: Check for MAC Flapping and STP Topology Changes<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Determine whether the storm is generated by a physical switching loop or an isolated babbling endpoint:<\/p>\n<pre><code class=\"language-text\">Switch# show logging | include MACFLAP|Topology\n<\/code><\/pre>\n<ul>\n<li><strong>Presence of MAC Flap logs:<\/strong> Log messages such as <code>%SW_MATM-4-MACFLAP_NOTIF: Host 0050.56a1.b2c3 in vlan 10 is flapping between port Gi1\/0\/24 and port Gi1\/0\/48<\/code> prove that an active Layer 2 loop is circulating frames across multiple paths.<\/li>\n<li><strong>Rapid STP Topology Changes:<\/strong> Execute <code>show spanning-tree detail | include is exec|from|Topology<\/code>. Rapidly incrementing topology change counters confirm that link transitions are repeatedly resetting the CAM table, triggering unknown unicast and broadcast flooding across the domain.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Trace_Downstream_Infrastructure_via_CDP_and_LLDP\"><\/span>Step 3: Trace Downstream Infrastructure via CDP and LLDP<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Once the offending ingress interface is identified, determine what device resides on the other end:<\/p>\n<pre><code class=\"language-text\">Switch# show cdp neighbors GigabitEthernet1\/0\/1 detail\nSwitch# show lldp neighbors GigabitEthernet1\/0\/1 detail\n<\/code><\/pre>\n<ul>\n<li>If a downstream managed switch is detected, log into that switch and repeat Steps 1 and 2 to traverse the tree toward the root source.<\/li>\n<li>If no neighbor is found, query the MAC address table on that interface:<br \/>\n  <code>text<br \/>\n  Switch# show mac address-table interface GigabitEthernet1\/0\/1<\/code><br \/>\n  If dozens of MAC addresses appear on a non-trunk access port, an unmanaged switch or bridging hypervisor is attached to that port. If only one MAC address is present, that individual host is the source.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Capture_Ingress_Traffic_Using_Local_SPAN\"><\/span>Step 4: Capture Ingress Traffic Using Local SPAN<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If the source MAC must be analyzed to identify a malicious or malfunctioning application, mirror incoming traffic from the suspect port to a network analyzer:<\/p>\n<pre><code class=\"language-text\">Switch(config)# monitor session 1 source interface GigabitEthernet1\/0\/1 rx\nSwitch(config)# monitor session 1 destination interface GigabitEthernet1\/0\/10\n<\/code><\/pre>\n<p>Connecting a protocol analyzer to interface <code>Gi1\/0\/10<\/code> reveals the originating Layer 2 MAC address, ARP payload details, or network protocol causing the traffic surge.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Execute_Containment_and_Administrative_Shutdown\"><\/span>Step 5: Execute Containment and Administrative Shutdown<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Once the interface is isolated, disable the port immediately to restore normal network operations across the remaining infrastructure:<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface GigabitEthernet1\/0\/1\nSwitch(config-if)# shutdown\n<\/code><\/pre>\n<p>Observe CPU utilization and interface error rates; within 10 to 30 seconds of shutting down the ingress port, switch CPU metrics should drop back to baseline levels.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_Catalyst_and_NX-OS_Storm_Control_Architecture_and_Reference\"><\/span>Cisco Catalyst and NX-OS Storm Control Architecture and Reference<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>To prevent recurring outages, Cisco switches provide hardware-enforced <strong>Traffic Storm Control<\/strong>. The feature operates directly within the switching bus and port ASICs, monitoring traffic rates over microsecond-level intervals and discarding excess packets without taxing the switch CPU.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Architectural_Overview\"><\/span>Architectural Overview<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Storm control functions by counting packet arrivals of a designated traffic type (broadcast, multicast, or unknown unicast) passing from an ingress interface to the switching fabric. <\/p>\n<pre><code>Traffic Rate\n    ^\n    |          \/---\\            &lt;- Traffic exceeds Rising Threshold (T1)\n    |         \/     \\              [Action: Traffic Dropped \/ Port Suppressed]\nThreshold --\/-------\\---------------------------------- (Rising Threshold)\n    |      \/         \\\n    |     \/           \\         &lt;- Traffic drops below Falling Threshold (T2)\nThreshold - - - - - - -\\ - - - - - - - - - - - - - - - (Falling Threshold)\n    |                   \\___    [Action: Normal Forwarding Resumed]\n    +----------------------------------------------------&gt; Time\n<\/code><\/pre>\n<ol>\n<li><strong>Measurement Interval:<\/strong> The switch counts incoming frames over a 1-second internal polling window.<\/li>\n<li><strong>Threshold Calculation:<\/strong> Thresholds can be defined as a percentage of total interface bandwidth (<code>level 0.00 - 100.00<\/code>), packets per second (<code>pps<\/code>), or bits per second (<code>bps<\/code>).<\/li>\n<li><strong>Suppression Algorithm:<\/strong><\/li>\n<li>When ingress broadcast traffic exceeds the configured <strong>rising threshold<\/strong>, the ASIC drops all incoming broadcast frames on that interface for the remainder of the interval. Regular unicast traffic continues to pass uninterrupted.<\/li>\n<li>If an optional <strong>falling threshold<\/strong> is defined, broadcast forwarding only resumes after traffic drops below that lower baseline. If no falling threshold is set, the switch uses the rising threshold as the release point.<\/li>\n<li><strong>Mitigation Action:<\/strong> By default, excess frames are silently dropped while the port remains up (<code>filtering<\/code>). Optionally, the switch can generate SNMP traps or place the entire interface into the <code>err-disable<\/code> state.<\/li>\n<\/ol>\n<h3><span class=\"ez-toc-section\" id=\"Cisco_IOS_IOS-XE_vs_NX-OS_Command_Reference\"><\/span>Cisco IOS \/ IOS-XE vs. NX-OS Command Reference<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Parameter \/ Action<\/th>\n<th style=\"text-align: left;\">Cisco IOS \/ IOS-XE (Catalyst 9000 \/ 3850)<\/th>\n<th style=\"text-align: left;\">Cisco NX-OS (Nexus 9000 \/ 7000 \/ 3000)<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Apply Broadcast Threshold<\/strong><\/td>\n<td style=\"text-align: left;\"><code>storm-control broadcast level &lt;rising&gt; [&lt;falling&gt;]<\/code><\/td>\n<td style=\"text-align: left;\"><code>storm-control broadcast level &lt;percentage&gt;<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Threshold by PPS \/ BPS<\/strong><\/td>\n<td style=\"text-align: left;\"><code>storm-control broadcast level pps &lt;pps&gt; [&lt;pps-low&gt;]<\/code><\/td>\n<td style=\"text-align: left;\">Not universally supported across all ASIC types<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Automated Trap Action<\/strong><\/td>\n<td style=\"text-align: left;\"><code>storm-control action trap<\/code><\/td>\n<td style=\"text-align: left;\"><code>snmp-server enable traps link storm-control<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Shutdown Interface Action<\/strong><\/td>\n<td style=\"text-align: left;\"><code>storm-control action shutdown<\/code><\/td>\n<td style=\"text-align: left;\">Supported via EEM policy or port-security hooks<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Verification Command<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show storm-control [interface] [broadcast]<\/code><\/td>\n<td style=\"text-align: left;\"><code>show interface &lt;id&gt; counters storm-control<\/code><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3><span class=\"ez-toc-section\" id=\"Platform_Caveats_and_Operational_Constraints\"><\/span>Platform Caveats and Operational Constraints<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>EtherChannels \/ Link Aggregation:<\/strong> Storm control must be applied directly to the logical <code>Port-channel<\/code> interface on IOS-XE devices; the configuration automatically propagates to all bundled physical member ports.<\/li>\n<li><strong>Control-Plane Multicast Leakage:<\/strong> On older Catalyst platforms, configuring multicast storm control without distinguishing control traffic can inadvertently drop critical Layer 2 and Layer 3 control frames, such as OSPF hellos, EIGRP packets, PIM joins, and CDP\/LLDP messages. Modern Catalyst 9000 switches segregate control-plane multicast protocols from user data multicast to prevent control-session drops.<\/li>\n<li><strong>Granularity and Burstiness:<\/strong> Storm control is calculated using short time slices. A bursty client application that sends an instantaneous 100 Mbps burst of broadcasts for 50 milliseconds on a 1 Gbps port may not trip a 20% average threshold, but can still induce microburst drops on lower-speed egress uplinks.<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Production-Ready_Cisco_Storm_Control_Configuration_Template\"><\/span>Production-Ready Cisco Storm Control Configuration Template<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>The following production template configures broadcast storm control on user-facing access ports, enables SNMP traps for visibility, and implements automated <code>errdisable<\/code> recovery so administrative intervention is not required once an offending client disconnects.<\/p>\n<pre><code class=\"language-text\">! =====================================================================\n! SECTION 1: GLOBAL AUTOMATIC ERROR-DISABLE RECOVERY SETUP\n! =====================================================================\nconfigure terminal\n\n! Enable automatic port recovery if storm-control forces a shutdown\nerrdisable recovery cause storm-control\nerrdisable recovery interval 300\n\n! Enable global SNMP trap generation for link and security exceptions\nsnmp-server enable traps storm-control trap-rate 10\nexit\n\n! =====================================================================\n! SECTION 2: ACCESS PORT-RANGE TEMPLATE DEPLOYMENT\n! =====================================================================\nconfigure terminal\ninterface range GigabitEthernet1\/0\/1 - 48\n\n ! Apply broadcast suppression: Rising threshold 20.00%, Falling 15.00%\n storm-control broadcast level 20.00 15.00\n\n ! Optional: Suppress unknown unicast traffic to mitigate MAC table exhaustion\n storm-control unicast level 10.00 5.00\n\n ! Configure alerting and automated shutdown\n storm-control action trap\n storm-control action shutdown\n\n ! Defensive hardening: Block physical bridging loops on edge ports\n switchport mode access\n spanning-tree portfast\n spanning-tree bpduguard enable\n\n exit\n\n! =====================================================================\n! SECTION 3: RECOVERY AND VERIFICATION\n! =====================================================================\n! Verify operational state across all ports\nshow storm-control broadcast\nshow errdisable recovery\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Comparative_Analysis_Network_Monitoring_and_Packet_Inspection_Tools\"><\/span>Comparative Analysis: Network Monitoring and Packet Inspection Tools<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While on-box CLI commands isolate active emergencies, proactive network monitoring tools allow engineers to detect abnormal broadcast elevations before they cause full-scale network degradation.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Tool<\/th>\n<th style=\"text-align: left;\">Primary Detection Mechanism<\/th>\n<th style=\"text-align: left;\">Alerting Capabilities<\/th>\n<th style=\"text-align: left;\">Packet Inspection Depth<\/th>\n<th style=\"text-align: left;\">Deployment Complexity<\/th>\n<th style=\"text-align: left;\">Best Used For<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Wireshark<\/strong><\/td>\n<td style=\"text-align: left;\">Direct packet capture via SPAN\/RSPAN or TAP<\/td>\n<td style=\"text-align: left;\">None (reactive diagnostic utility)<\/td>\n<td style=\"text-align: left;\">Deepest available; full decode of Layer 2 to Layer 7 frame headers<\/td>\n<td style=\"text-align: left;\">Low (runs on any engineer workstation)<\/td>\n<td style=\"text-align: left;\">Root-cause forensic analysis to isolate the exact source MAC, IP, and offending application payload.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>PRTG Network Monitor<\/strong><\/td>\n<td style=\"text-align: left;\">SNMP Interface Counters, NetFlow, and Packet Sniffing<\/td>\n<td style=\"text-align: left;\">Built-in email, SMS, and webhook alerts on customizable threshold breaches<\/td>\n<td style=\"text-align: left;\">Moderate; reports protocol ratios and top talkers, but limited raw hex decode<\/td>\n<td style=\"text-align: left;\">Low to Medium; agentless sensor architecture<\/td>\n<td style=\"text-align: left;\">Mid-sized campus environments needing quick out-of-the-box alerts when broadcast traffic exceeds baseline ratios.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>SolarWinds NPM<\/strong><\/td>\n<td style=\"text-align: left;\">Multi-vendor SNMP polling, WMI, and flow records<\/td>\n<td style=\"text-align: left;\">Complex policy-based alerting engine with automated execution scripts<\/td>\n<td style=\"text-align: left;\">Low to Moderate; highlights interface utilization, discard spikes, and packet types<\/td>\n<td style=\"text-align: left;\">Medium to High; requires dedicated database and server infrastructure<\/td>\n<td style=\"text-align: left;\">Enterprise monitoring across large multivendor topologies with automated ticketing system integrations.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Cisco Catalyst Center<\/strong><\/td>\n<td style=\"text-align: left;\">Streaming telemetry, DNA traffic analytics, and Syslog<\/td>\n<td style=\"text-align: left;\">AI-driven anomaly detection; flags storm events via health scores and alarms<\/td>\n<td style=\"text-align: left;\">High; combines NetFlow\/telemetry with device-level control-plane health<\/td>\n<td style=\"text-align: left;\">High; requires Cisco appliance clusters and compatible Catalyst switches<\/td>\n<td style=\"text-align: left;\">Cisco-centric enterprise environments requiring end-to-end telemetry and automated fabric-level troubleshooting.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3><span class=\"ez-toc-section\" id=\"Essential_Wireshark_Display_and_Capture_Filters\"><\/span>Essential Wireshark Display and Capture Filters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When capturing traffic from a mirrored switch port during a suspected storm, apply these filters to eliminate regular data and pinpoint the flooding application:<\/p>\n<ul>\n<li>\n<p><strong>Capture Filter (applied before capture begins):<\/strong><br \/>\n  <code>text<br \/>\n  ether proto 0x0806 or ether dst ff:ff:ff:ff:ff:ff<\/code><br \/>\n  <em>Captures only Layer 2 ARP frames and general broadcast traffic.<\/em><\/p>\n<\/li>\n<li>\n<p><strong>Display Filter (applied during analysis):<\/strong><br \/>\n  <code>text<br \/>\n  eth.dst == ff:ff:ff:ff:ff:ff &amp;&amp; (eth.type == 0x0806 || ip.proto == 17)<\/code><br \/>\n  <em>Isolates Layer 2 broadcast destinations running ARP or UDP-based broadcast services (such as DHCP and NetBIOS).<\/em><\/p>\n<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Detecting and mitigating a broadcast storm in a Cisco switching environment requires a structured balance of immediate troubleshooting and robust architectural defense. During an active incident, monitoring control-plane interrupt CPU levels, tracing input versus output broadcast counters, and checking for MAC address flapping quickly directs engineers to the rogue ingress port. Once identified, disabling the interface stops network degradation immediately.<\/p>\n<p>To protect production switches from future incidents, relying on Spanning Tree Protocol alone is insufficient. Implementing hardware-level traffic storm control with clear rising and falling thresholds, enabling automated error-disable recovery, and coupling edge ports with BPDU Guard establishes an automated first line of defense. Paired with proactive SNMP or telemetry monitoring, this layered approach ensures that broadcast anomalies are suppressed at the port level before they can impact overall network operations.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-check-broadcast-storm-in-cisco-switch_24521.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Check+Broadcast+Storm+in+Cisco+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\",\"How to Check Broadcast Storm in Cisco Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>A broadcast storm is one of the most disruptive events that can strike a local area network. When Layer 2 broadcast or multicast frames replicate uncontrollably across a switching domain, available link bandwidth vanishes within seconds. Network latency surges, endpoints lose connectivity as ARP and DHCP packets fail to resolve, and switch control planes become&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"A broadcast storm is one of the most disruptive events that can strike a local area network. When Layer 2 broadcast or multicast frames replicate uncontrollably across a switching domain, available link bandwidth vanishes within seconds. Network latency surges, endpoints lose connectivity as ARP and DHCP packets fail to resolve, and switch control planes become... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-16T03:54:15+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"13 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\",\"name\":\"How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-16T03:54:15+00:00\",\"dateModified\":\"2026-11-16T03:54:15+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Check Broadcast Storm in Cisco Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Check Broadcast Storm in Cisco Switch\",\"datePublished\":\"2026-11-16T03:54:15+00:00\",\"dateModified\":\"2026-11-16T03:54:15+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage\"},\"wordCount\":2069,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html","og_locale":"en_US","og_type":"article","og_title":"How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog","og_description":"A broadcast storm is one of the most disruptive events that can strike a local area network. When Layer 2 broadcast or multicast frames replicate uncontrollably across a switching domain, available link bandwidth vanishes within seconds. Network latency surges, endpoints lose connectivity as ARP and DHCP packets fail to resolve, and switch control planes become... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-16T03:54:15+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"13 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html","name":"How to Check Broadcast Storm in Cisco Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-16T03:54:15+00:00","dateModified":"2026-11-16T03:54:15+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Check Broadcast Storm in Cisco Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Check Broadcast Storm in Cisco Switch","datePublished":"2026-11-16T03:54:15+00:00","dateModified":"2026-11-16T03:54:15+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#webpage"},"wordCount":2069,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-check-broadcast-storm-in-cisco-switch_24521.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24521"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24521"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24521\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24521"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24521"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24521"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}