{"id":24491,"date":"2026-11-16T10:59:35","date_gmt":"2026-11-16T02:59:35","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html"},"modified":"2026-11-16T10:59:35","modified_gmt":"2026-11-16T02:59:35","slug":"how-to-assign-loopback-address-on-cisco-router","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html","title":{"rendered":"How to Assign Loopback Address on Cisco Router"},"content":{"rendered":"<p>In Cisco IOS and IOS XE networking, a loopback interface is a logical, virtual software interface that is not bound to any physical port or external hardware link. Unlike physical Ethernet or serial interfaces that transition to a &#8220;down\/down&#8221; state when a patch cable is unplugged or a link partner reboots, a loopback interface remains permanently active and operational as long as the router itself is powered on. Because of this inherent resilience, network engineers deploy loopback interfaces as primary management targets, reliable termination endpoints for VPN tunnels, and stable identifiers for dynamic routing protocols.<\/p>\n<p>Understanding how to properly create, configure, and verify loopback interfaces is a foundational skill for configuring any Cisco router.<\/p>\n<hr \/>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Architectural_Purpose_and_Subnet_Masking_Frequently_Asked_Questions\" title=\"Architectural Purpose and Subnet Masking: Frequently Asked Questions\">Architectural Purpose and Subnet Masking: Frequently Asked Questions<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#What_is_the_primary_purpose_of_a_loopback_interface_on_a_Cisco_router\" title=\"What is the primary purpose of a loopback interface on a Cisco router?\">What is the primary purpose of a loopback interface on a Cisco router?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Why_is_a_32_subnet_mask_standard_practice_for_loopback_interfaces\" title=\"Why is a \/32 subnet mask standard practice for loopback interfaces?\">Why is a \/32 subnet mask standard practice for loopback interfaces?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#When_would_a_network_engineer_use_a_subnet_mask_other_than_32\" title=\"When would a network engineer use a subnet mask other than \/32?\">When would a network engineer use a subnet mask other than \/32?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Loopback_Interface_vs_Physical_Interface_for_Router_Identification\" title=\"Loopback Interface vs. Physical Interface for Router Identification\">Loopback Interface vs. Physical Interface for Router Identification<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step-by-Step_Guide_Configuring_an_IPv4_Loopback_Address\" title=\"Step-by-Step Guide: Configuring an IPv4 Loopback Address\">Step-by-Step Guide: Configuring an IPv4 Loopback Address<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step_1_Access_Privileged_EXEC_and_Global_Configuration_Mode\" title=\"Step 1: Access Privileged EXEC and Global Configuration Mode\">Step 1: Access Privileged EXEC and Global Configuration Mode<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step_2_Create_the_Loopback_Interface\" title=\"Step 2: Create the Loopback Interface\">Step 2: Create the Loopback Interface<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step_3_Assign_the_IPv4_Address_and_Host_Subnet_Mask\" title=\"Step 3: Assign the IPv4 Address and Host Subnet Mask\">Step 3: Assign the IPv4 Address and Host Subnet Mask<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step_4_Add_an_Administrative_Description\" title=\"Step 4: Add an Administrative Description\">Step 4: Add an Administrative Description<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Step_5_Exit_and_Save_Configuration\" title=\"Step 5: Exit and Save Configuration\">Step 5: Exit and Save Configuration<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Configuring_IPv6_on_a_Cisco_Loopback_Interface\" title=\"Configuring IPv6 on a Cisco Loopback Interface\">Configuring IPv6 on a Cisco Loopback Interface<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Configuration_Template\" title=\"Configuration Template\">Configuration Template<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Runnable_Configuration_Example\" title=\"Runnable Configuration Example\">Runnable Configuration Example<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Verifying_and_Troubleshooting_Loopback_Interfaces\" title=\"Verifying and Troubleshooting Loopback Interfaces\">Verifying and Troubleshooting Loopback Interfaces<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#1_Verify_Operational_and_Protocol_Status\" title=\"1. Verify Operational and Protocol Status\">1. Verify Operational and Protocol Status<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#2_Inspect_Interface_Details_and_MTU_Settings\" title=\"2. Inspect Interface Details and MTU Settings\">2. Inspect Interface Details and MTU Settings<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#3_Diagnose_Common_Troubleshooting_Scenarios\" title=\"3. Diagnose Common Troubleshooting Scenarios\">3. Diagnose Common Troubleshooting Scenarios<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Official_Documentation_and_Command_Reference\" title=\"Official Documentation and Command Reference\">Official Documentation and Command Reference<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Command_Syntax_Reference\" title=\"Command Syntax Reference\">Command Syntax Reference<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\/#Cisco_Technical_Documentation_Navigation\" title=\"Cisco Technical Documentation Navigation\">Cisco Technical Documentation Navigation<\/a><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Architectural_Purpose_and_Subnet_Masking_Frequently_Asked_Questions\"><\/span>Architectural Purpose and Subnet Masking: Frequently Asked Questions<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Before entering the command line, understanding the architectural role of virtual loopback interfaces clarifies why certain configuration conventions\u2014such as the standard \/32 host mask\u2014are universal industry standards.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"What_is_the_primary_purpose_of_a_loopback_interface_on_a_Cisco_router\"><\/span>What is the primary purpose of a loopback interface on a Cisco router?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>A loopback interface provides a stable, hardware-independent IP address for the router. In enterprise networks, physical interfaces can flap, experience line-protocol drops, or undergo hardware servicing. If network management tools (like SSH, SNMP, or Syslog) or dynamic routing protocols (like OSPF or BGP) bind to a physical IP address, any link failure severs communication or forces routing protocol recalculations. By binding these services to a loopback interface, the router remains reachable across any alternate physical path available in the network topology.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_is_a_32_subnet_mask_standard_practice_for_loopback_interfaces\"><\/span>Why is a \/32 subnet mask standard practice for loopback interfaces?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>In IPv4 addressing, a <code>\/32<\/code> mask (<code>255.255.255.255<\/code>) specifies a single host address without any broadcast or network overhead. Because a loopback interface is internal to the router&#8217;s control plane and will never have other physical hosts sharing its broadcast domain, assigning a subnet with multiple host addresses (such as a <code>\/24<\/code> or <code>\/30<\/code>) wastes scarce IPv4 addresses. A <code>\/32<\/code> subnet mask conserves address space while providing a fully routable host route that routing protocols can easily propagate throughout the autonomous system.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"When_would_a_network_engineer_use_a_subnet_mask_other_than_32\"><\/span>When would a network engineer use a subnet mask other than \/32?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Subnet masks such as <code>\/24<\/code> or <code>\/28<\/code> are generally reserved for lab testing, simulation environments, or legacy routing scenarios where an engineer needs to simulate an entire multi-host LAN segment behind the router without attaching real physical switches and endpoints. In production environments, production loopbacks almost universally utilize a <code>\/32<\/code> mask (or <code>\/128<\/code> in IPv6).<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Loopback_Interface_vs_Physical_Interface_for_Router_Identification\"><\/span>Loopback Interface vs. Physical Interface for Router Identification<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Because loopback interfaces do not rely on physical media, they offer distinct operational characteristics compared to physical ports when chosen for router identification and administrative access.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Feature \/ Criteria<\/th>\n<th style=\"text-align: left;\">Loopback Interface<\/th>\n<th style=\"text-align: left;\">Physical Interface<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Operational Stability<\/strong><\/td>\n<td style=\"text-align: left;\">Always in an <code>up\/up<\/code> state unless administratively shut down; immune to cable cuts and port failures.<\/td>\n<td style=\"text-align: left;\">Dependent on physical transceiver, cable integrity, and peer device status; flaps when link fails.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Dynamic Routing Router ID (OSPF\/BGP)<\/strong><\/td>\n<td style=\"text-align: left;\">Preferred. Guarantees a persistent Router ID (RID); prevents neighbor renegotiation and protocol drops.<\/td>\n<td style=\"text-align: left;\">Flap-prone. If the chosen physical interface goes down, OSPF or BGP may renegotiate RID, resetting adjacency.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Management Reachability (SSH\/SNMP)<\/strong><\/td>\n<td style=\"text-align: left;\">Accessible via any active routed physical path traversing the router.<\/td>\n<td style=\"text-align: left;\">Inaccessible if that specific physical interface or its direct link fails, even if alternate paths exist.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>IP Address Conservation<\/strong><\/td>\n<td style=\"text-align: left;\">Supports <code>\/32<\/code> host masks (IPv4) and <code>\/128<\/code> (IPv6), consuming only a single IP per interface.<\/td>\n<td style=\"text-align: left;\">Requires a subnet (e.g., <code>\/30<\/code>, <code>\/31<\/code>, <code>\/24<\/code>) shared with the connected neighbor device.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Direct Host Attachment<\/strong><\/td>\n<td style=\"text-align: left;\">Cannot attach external network nodes, switches, or end-user endpoints directly.<\/td>\n<td style=\"text-align: left;\">Directly attaches patch cables, transceivers, and Layer 2 infrastructure.<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Diagnostic Utility<\/strong><\/td>\n<td style=\"text-align: left;\">Terminates test pings, GRE\/IPsec tunnels, and BGP multi-hop sessions reliably.<\/td>\n<td style=\"text-align: left;\">Confined to testing physical connectivity and direct Layer 1\/Layer 2 link health.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>Takeaway: Always assign routing protocol IDs and management bindings to a virtual loopback interface rather than a physical interface to protect network convergence from physical link instability.<\/em><\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_Guide_Configuring_an_IPv4_Loopback_Address\"><\/span>Step-by-Step Guide: Configuring an IPv4 Loopback Address<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Configuring an IPv4 loopback interface on Cisco IOS or IOS XE is straightforward and can be completed in privileged configuration mode.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Access_Privileged_EXEC_and_Global_Configuration_Mode\"><\/span>Step 1: Access Privileged EXEC and Global Configuration Mode<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Log in to your router via console or SSH and elevate to global configuration mode:<\/p>\n<pre><code class=\"language-cisco\">Router&gt; enable\nRouter# configure terminal\nRouter(config)#\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Create_the_Loopback_Interface\"><\/span>Step 2: Create the Loopback Interface<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Invoke the <code>interface loopback<\/code> command followed by an instance number. Cisco IOS supports values from <code>0<\/code> to <code>2147483647<\/code>. By convention, the primary management loopback is named <code>Loopback0<\/code>.<\/p>\n<pre><code class=\"language-cisco\">Router(config)# interface loopback 0\nRouter(config-if)#\n<\/code><\/pre>\n<p><em>Note: If the loopback interface did not previously exist, Cisco IOS creates it dynamically the moment this command is entered.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Assign_the_IPv4_Address_and_Host_Subnet_Mask\"><\/span>Step 3: Assign the IPv4 Address and Host Subnet Mask<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Apply the desired IP address along with a <code>\/32<\/code> subnet mask (<code>255.255.255.255<\/code>):<\/p>\n<pre><code class=\"language-cisco\">Router(config-if)# ip address 192.168.100.1 255.255.255.255\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Add_an_Administrative_Description\"><\/span>Step 4: Add an Administrative Description<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Adding a descriptive label ensures clarity for network auditing and operational monitoring:<\/p>\n<pre><code class=\"language-cisco\">Router(config-if)# description Primary_Management_and_OSPF_RID\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Exit_and_Save_Configuration\"><\/span>Step 5: Exit and Save Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Unlike physical interfaces, loopback interfaces are administratively enabled (<code>no shutdown<\/code>) by default upon creation. Exit configuration mode and save your changes to the startup configuration:<\/p>\n<pre><code class=\"language-cisco\">Router(config-if)# end\nRouter# copy running-config startup-config\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Configuring_IPv6_on_a_Cisco_Loopback_Interface\"><\/span>Configuring IPv6 on a Cisco Loopback Interface<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>In modern dual-stack or IPv6-only architectures, routers require an IPv6 loopback address. IPv6 loopback interfaces follow the same principle as IPv4, using a <code>\/128<\/code> prefix to designate a single, host-specific address.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Configuration_Template\"><\/span>Configuration Template<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-cisco\">enable\nconfigure terminal\nipv6 unicast-routing\ninterface Loopback[INSTANCE_NUMBER]\n description [OPTIONAL_INTERFACE_DESCRIPTION]\n ipv6 address [IPV6_GLOBAL_UNICAST_ADDRESS]\/128\n ipv6 address fe80::[IDENTIFIER] link-local\nexit\nend\ncopy running-config startup-config\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Runnable_Configuration_Example\"><\/span>Runnable Configuration Example<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-cisco\">Router# configure terminal\nRouter(config)# ipv6 unicast-routing\nRouter(config)# interface loopback 0\nRouter(config-if)# description Global_IPv6_Router_ID\nRouter(config-if)# ipv6 address 2001:db8:1000:1::1\/128\nRouter(config-if)# ipv6 address fe80::1 link-local\nRouter(config-if)# end\nRouter# write memory\n<\/code><\/pre>\n<p><em>Takeaway: Always ensure <code>ipv6 unicast-routing<\/code> is enabled globally, and assign a <code>\/128<\/code> prefix to mirror the host-isolation benefits of an IPv4 <code>\/32<\/code> mask.<\/em><\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Verifying_and_Troubleshooting_Loopback_Interfaces\"><\/span>Verifying and Troubleshooting Loopback Interfaces<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Once configured, verify that the loopback interface is active in the routing table and accessible across the local control plane.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"1_Verify_Operational_and_Protocol_Status\"><\/span>1. Verify Operational and Protocol Status<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Run the <code>show ip interface brief<\/code> command to confirm the Layer 1 (Status) and Layer 2 (Protocol) operational states:<\/p>\n<pre><code class=\"language-cisco\">Router# show ip interface brief | include Loopback\nLoopback0              192.168.100.1   YES manual up                    up\n<\/code><\/pre>\n<p>Both the <code>Status<\/code> and <code>Protocol<\/code> columns should read <code>up<\/code>.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"2_Inspect_Interface_Details_and_MTU_Settings\"><\/span>2. Inspect Interface Details and MTU Settings<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To review detailed counters, encapsulation, and administrative descriptions:<\/p>\n<pre><code class=\"language-cisco\">Router# show interfaces loopback 0\nLoopback0 is up, line protocol is up \n  Hardware is Loopback\n  Description: Primary_Management_and_OSPF_RID\n  Internet address is 192.168.100.1\/32\n  MTU 1514 bytes, BW 8000000 Kbit\/sec, DLY 5000 usec, \n     reliability 255\/255, txload 1\/255, rxload 1\/255\n  Encapsulation LOOPBACK, loopback not set\n  Last input never, output never, output hang never\n  Last clearing of &quot;show interface&quot; counters never\n  Input queue: 0\/75\/0\/0 (size\/max\/drops\/flushes); Total output drops: 0\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"3_Diagnose_Common_Troubleshooting_Scenarios\"><\/span>3. Diagnose Common Troubleshooting Scenarios<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>State Shows <code>administratively down \/ down<\/code>:<\/strong>\n<ul>\n<li><em>Cause:<\/em> An administrator manually executed the <code>shutdown<\/code> command on the interface.<\/li>\n<li><em>Solution:<\/em> Enter interface configuration mode and execute <code>no shutdown<\/code>:<br \/>\n    <code>cisco<br \/>\n    Router(config)# interface loopback 0<br \/>\n    Router(config-if)# no shutdown<\/code><\/li>\n<\/ul>\n<\/li>\n<li><strong>Loopback Responds Locally but Not from Remote Subnets:<\/strong>\n<ul>\n<li><em>Cause:<\/em> The loopback IP address is working locally, but upstream routers have no route back to the loopback&#8217;s <code>\/32<\/code> or <code>\/128<\/code> address.<\/li>\n<li><em>Solution:<\/em> Advertise the loopback interface into your routing protocol. For example, in OSPF:<br \/>\n    <code>cisco<br \/>\n    Router(config)# router ospf 1<br \/>\n    Router(config-router)# network 192.168.100.1 0.0.0.0 area 0<\/code><br \/>\n    Alternatively, enable OSPF directly on the interface using <code>ip ospf 1 area 0<\/code>.<\/li>\n<\/ul>\n<\/li>\n<li><strong>Management Traffic Dropping (SSH\/SNMP):<\/strong>\n<ul>\n<li><em>Cause:<\/em> An Access Control List (ACL) applied to the virtual terminal lines (<code>line vty 0 4<\/code>) or a Control Plane Policing (CoPP) policy is filtering traffic destined for the loopback address.<\/li>\n<li><em>Solution:<\/em> Check <code>show ip access-lists<\/code> and verify that incoming packets from the management subnet are permitted.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Official_Documentation_and_Command_Reference\"><\/span>Official Documentation and Command Reference<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>For comprehensive implementation guidelines across enterprise platforms, refer to Cisco&#8217;s official technical command standards:<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Command_Syntax_Reference\"><\/span>Command Syntax Reference<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Command:<\/strong> <code>interface loopback &lt;number&gt;<\/code>\n<ul>\n<li><strong>Syntax Description:<\/strong> <code>&lt;number&gt;<\/code> specifies the unique loopback interface number. Supported values range from <code>0<\/code> to <code>2147483647<\/code>.<\/li>\n<li><strong>Command Mode:<\/strong> Global Configuration (<code>Router(config)#<\/code>).<\/li>\n<li><strong>Default State:<\/strong> Enabled and operational (<code>up\/up<\/code>) upon creation. No physical transceivers or clocking commands apply.<\/li>\n<li><strong>Supported Platforms:<\/strong> Cisco 800\/1000\/4000 Series ISRs, Catalyst 8000 Edge Platforms, ASR 1000\/9000 Series, and Catalyst Layer 3 switches (3650, 3850, 9200, 9300, 9500).<\/li>\n<li><strong>Operating Systems:<\/strong> Cisco IOS Software Releases 12.2 through 15.x; Cisco IOS XE Releases 16.x through 17.x; Cisco IOS XR.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Cisco_Technical_Documentation_Navigation\"><\/span>Cisco Technical Documentation Navigation<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To locate official Cisco configuration guides for your specific platform and operating system release:<br \/>\n1. Navigate to the <strong>Cisco Support &amp; Downloads<\/strong> portal.<br \/>\n2. Select <strong>Routers<\/strong> (or <strong>Switches<\/strong>) and choose your hardware family (e.g., <em>Catalyst 8300 Series Edge Platforms<\/em>).<br \/>\n3. Under the <strong>Configure<\/strong> section, open the <strong>Configuration Guides<\/strong> tab.<br \/>\n4. Select the <strong>Interface and Hardware Component Configuration Guide<\/strong> for your deployed IOS XE train.<br \/>\n5. Review the specific chapter titled <em>&#8220;Configuring Logical Interfaces&#8221;<\/em> or <em>&#8220;Configuring Loopback Interfaces.&#8221;<\/em><\/p>\n<hr \/>\n<p>Assigning a loopback address on a Cisco router provides an essential, hardware-independent anchor for network operations. By leveraging a <code>\/32<\/code> mask for IPv4 or a <code>\/128<\/code> prefix for IPv6, network engineers maximize address efficiency while ensuring uninterrupted reachability for network management and protocol operations. Once created, maintaining loopbacks involves minimal overhead: keep them active, announce them through your interior gateway routing protocol, and reserve physical interface addresses solely for point-to-point transit links.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-assign-loopback-address-on-cisco-router_24491.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Assign+Loopback+Address+on+Cisco+Router+https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\",\"How to Assign Loopback Address on Cisco Router\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>In Cisco IOS and IOS XE networking, a loopback interface is a logical, virtual software interface that is not bound to any physical port or external hardware link. Unlike physical Ethernet or serial interfaces that transition to a &#8220;down\/down&#8221; state when a patch cable is unplugged or a link partner reboots, a loopback interface remains&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Assign Loopback Address on Cisco Router - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Assign Loopback Address on Cisco Router - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"In Cisco IOS and IOS XE networking, a loopback interface is a logical, virtual software interface that is not bound to any physical port or external hardware link. Unlike physical Ethernet or serial interfaces that transition to a &#8220;down\/down&#8221; state when a patch cable is unplugged or a link partner reboots, a loopback interface remains... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-16T02:59:35+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"7 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\",\"name\":\"How to Assign Loopback Address on Cisco Router - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-16T02:59:35+00:00\",\"dateModified\":\"2026-11-16T02:59:35+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Assign Loopback Address on Cisco Router\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Assign Loopback Address on Cisco Router\",\"datePublished\":\"2026-11-16T02:59:35+00:00\",\"dateModified\":\"2026-11-16T02:59:35+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage\"},\"wordCount\":1272,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Assign Loopback Address on Cisco Router - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html","og_locale":"en_US","og_type":"article","og_title":"How to Assign Loopback Address on Cisco Router - SPOTO Official Blog","og_description":"In Cisco IOS and IOS XE networking, a loopback interface is a logical, virtual software interface that is not bound to any physical port or external hardware link. Unlike physical Ethernet or serial interfaces that transition to a &#8220;down\/down&#8221; state when a patch cable is unplugged or a link partner reboots, a loopback interface remains... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-16T02:59:35+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"7 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html","name":"How to Assign Loopback Address on Cisco Router - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-16T02:59:35+00:00","dateModified":"2026-11-16T02:59:35+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Assign Loopback Address on Cisco Router"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Assign Loopback Address on Cisco Router","datePublished":"2026-11-16T02:59:35+00:00","dateModified":"2026-11-16T02:59:35+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#webpage"},"wordCount":1272,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-assign-loopback-address-on-cisco-router_24491.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24491"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24491"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24491\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24491"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24491"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24491"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}