{"id":24482,"date":"2026-11-16T10:44:30","date_gmt":"2026-11-16T02:44:30","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html"},"modified":"2026-11-16T10:44:30","modified_gmt":"2026-11-16T02:44:30","slug":"how-to-change-mtu-on-cisco-switch-interface","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html","title":{"rendered":"How to Change MTU on Cisco Switch Interface"},"content":{"rendered":"<p>Maximum Transmission Unit (MTU) defines the maximum size of a packet or frame\u2014measured in bytes\u2014that a network interface can process and forward without fragmenting it. In enterprise and data center networks, adjusting the MTU beyond the standard Ethernet size of 1500 bytes to accommodate jumbo frames (typically up to 9000 or 9216 bytes) is essential for optimizing high-throughput traffic, such as iSCSI storage, NFS shares, hypervisor migrations, and network virtualization overlays like VXLAN and GRE.<\/p>\n<p>Configuring MTU incorrectly or allowing mismatches across adjacent network links introduces dropped frames, unexplained throughput degradation, and routing protocol neighbor failures. This comprehensive guide covers how to configure, automate, verify, and troubleshoot interface MTU across modern and legacy Cisco switch architectures.<\/p>\n<hr \/>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Understanding_System_MTU_vs_Interface_MTU\" title=\"Understanding System MTU vs. Interface MTU\">Understanding System MTU vs. Interface MTU<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#What_is_the_difference_between_System_MTU_and_Interface_MTU\" title=\"What is the difference between System MTU and Interface MTU?\">What is the difference between System MTU and Interface MTU?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Why_did_older_Cisco_Catalyst_switches_require_a_reload_to_change_MTU\" title=\"Why did older Cisco Catalyst switches require a reload to change MTU?\">Why did older Cisco Catalyst switches require a reload to change MTU?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#What_is_the_default_MTU_on_Cisco_switch_interfaces\" title=\"What is the default MTU on Cisco switch interfaces?\">What is the default MTU on Cisco switch interfaces?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#How_do_System_MTU_and_Interface_MTU_interact\" title=\"How do System MTU and Interface MTU interact?\">How do System MTU and Interface MTU interact?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step-by-Step_Guide_Configuring_Interface_MTU_on_Cisco_Catalyst_IOS-XE\" title=\"Step-by-Step Guide: Configuring Interface MTU on Cisco Catalyst (IOS-XE)\">Step-by-Step Guide: Configuring Interface MTU on Cisco Catalyst (IOS-XE)<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_1_Enter_Global_Configuration_Mode\" title=\"Step 1: Enter Global Configuration Mode\">Step 1: Enter Global Configuration Mode<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_2_Configure_MTU_on_a_Layer_2_Switchport_Access_or_Trunk\" title=\"Step 2: Configure MTU on a Layer 2 Switchport (Access or Trunk)\">Step 2: Configure MTU on a Layer 2 Switchport (Access or Trunk)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_3_Configure_MTU_on_a_Layer_3_Routed_Port\" title=\"Step 3: Configure MTU on a Layer 3 Routed Port\">Step 3: Configure MTU on a Layer 3 Routed Port<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_4_Configure_MTU_on_a_Switched_Virtual_Interface_SVI\" title=\"Step 4: Configure MTU on a Switched Virtual Interface (SVI)\">Step 4: Configure MTU on a Switched Virtual Interface (SVI)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_5_Configure_MTU_on_a_Port-Channel_EtherChannel\" title=\"Step 5: Configure MTU on a Port-Channel (EtherChannel)\">Step 5: Configure MTU on a Port-Channel (EtherChannel)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_6_Save_the_Configuration\" title=\"Step 6: Save the Configuration\">Step 6: Save the Configuration<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#CLI_Configuration_Templates_for_Bulk_MTU_Changes\" title=\"CLI Configuration Templates for Bulk MTU Changes\">CLI Configuration Templates for Bulk MTU Changes<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Template_1_Bulk_Physical_AccessTrunk_Ports_Using_Interface_Range\" title=\"Template 1: Bulk Physical Access\/Trunk Ports Using Interface Range\">Template 1: Bulk Physical Access\/Trunk Ports Using Interface Range<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Template_2_Core_Infrastructure_Uplink_Trunks_Port-Channels_and_SVIs\" title=\"Template 2: Core Infrastructure (Uplink Trunks, Port-Channels, and SVIs)\">Template 2: Core Infrastructure (Uplink Trunks, Port-Channels, and SVIs)<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Template_3_Global_System_Baseline_MTU_Configuration\" title=\"Template 3: Global System Baseline MTU Configuration\">Template 3: Global System Baseline MTU Configuration<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Verifying_MTU_Settings_and_Testing_Jumbo_Frames\" title=\"Verifying MTU Settings and Testing Jumbo Frames\">Verifying MTU Settings and Testing Jumbo Frames<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_1_Verify_Configured_MTU_on_Interfaces\" title=\"Step 1: Verify Configured MTU on Interfaces\">Step 1: Verify Configured MTU on Interfaces<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Step_2_Validate_End-to-End_MTU_with_Do-Not-Fragment_DF_Pings\" title=\"Step 2: Validate End-to-End MTU with Do-Not-Fragment (DF) Pings\">Step 2: Validate End-to-End MTU with Do-Not-Fragment (DF) Pings<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Troubleshooting_MTU_Mismatches_and_OSPF_EXSTART_Hangs\" title=\"Troubleshooting MTU Mismatches and OSPF EXSTART Hangs\">Troubleshooting MTU Mismatches and OSPF EXSTART Hangs<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Issue_1_OSPF_Adjacency_Stuck_in_EXSTART_EXCHANGE\" title=\"Issue 1: OSPF Adjacency Stuck in EXSTART \/ EXCHANGE\">Issue 1: OSPF Adjacency Stuck in EXSTART \/ EXCHANGE<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Issue_2_Data-Plane_Packet_Drops_and_Giant_Counters\" title=\"Issue 2: Data-Plane Packet Drops and &#8220;Giant&#8221; Counters\">Issue 2: Data-Plane Packet Drops and &#8220;Giant&#8221; Counters<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-23\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Cisco_Catalyst_vs_Nexus_NX-OS_MTU_Configuration_Differences\" title=\"Cisco Catalyst vs. Nexus (NX-OS) MTU Configuration Differences\">Cisco Catalyst vs. Nexus (NX-OS) MTU Configuration Differences<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-24\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#The_NX-OS_Network-QoS_Difference\" title=\"The NX-OS Network-QoS Difference\">The NX-OS Network-QoS Difference<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-25\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Cisco_Catalyst_MTU_Technical_Reference_and_Command_Specifications\" title=\"Cisco Catalyst MTU Technical Reference and Command Specifications\">Cisco Catalyst MTU Technical Reference and Command Specifications<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-26\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#MTU_Framing_and_Wire_Overhead\" title=\"MTU Framing and Wire Overhead\">MTU Framing and Wire Overhead<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-27\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Platform_Support_Specifications\" title=\"Platform Support Specifications\">Platform Support Specifications<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-28\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Command_Reference\" title=\"Command Reference\">Command Reference<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-29\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\/#Conclusion\" title=\"Conclusion\">Conclusion<\/a><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Understanding_System_MTU_vs_Interface_MTU\"><\/span>Understanding System MTU vs. Interface MTU<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3><span class=\"ez-toc-section\" id=\"What_is_the_difference_between_System_MTU_and_Interface_MTU\"><\/span>What is the difference between System MTU and Interface MTU?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p><strong>System MTU<\/strong> is a global setting that establishes the baseline default MTU for all interfaces across the entire switch. When you modify the system MTU, any port without an explicit local override inherits this global value. <\/p>\n<p><strong>Interface MTU<\/strong> (also referred to as <strong>Per-Port MTU<\/strong>) is applied directly within an individual interface configuration mode\u2014such as a physical Ethernet port, an EtherChannel (Port-Channel), or a Switched Virtual Interface (SVI). Configuring an MTU at the interface level overrides the global system baseline for that specific port.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_did_older_Cisco_Catalyst_switches_require_a_reload_to_change_MTU\"><\/span>Why did older Cisco Catalyst switches require a reload to change MTU?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On legacy Cisco Catalyst platforms (such as the Catalyst 2960, 3560, and 3750 series running classic Cisco IOS), switch ASIC packet buffers were statically allocated during initialization. Changing the maximum frame size with commands like <code>system mtu jumbo &lt;bytes&gt;<\/code> required a full hardware reload (<code>reload<\/code>) to repartition memory buffers. <\/p>\n<p>In contrast, modern Catalyst switches (including the Catalyst 3650, 3850, and the entire Catalyst 9000 series running Cisco IOS-XE) support dynamic ASIC buffer management. As of Cisco IOS-XE Amsterdam 17.1.1, these platforms support per-port MTU adjustments that take effect immediately without requiring a reboot.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"What_is_the_default_MTU_on_Cisco_switch_interfaces\"><\/span>What is the default MTU on Cisco switch interfaces?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The default MTU on all Cisco Catalyst switch interfaces is <strong>1500 bytes<\/strong>. This value represents the maximum Layer 3 payload size (the IP packet, including IP and transport headers) that standard Ethernet frames carry. The Layer 2 frame overhead (a 14-byte Ethernet header plus a 4-byte Frame Check Sequence, along with any optional 4-byte 802.1Q VLAN tags) is tracked separately by the switch hardware.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"How_do_System_MTU_and_Interface_MTU_interact\"><\/span>How do System MTU and Interface MTU interact?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When an interface is configured with a specific per-port MTU, that port uses its local value regardless of the system MTU. If you remove the port-level configuration using the <code>no mtu<\/code> command, the interface automatically reverts to the global system MTU value. On some platforms, the global system MTU acts as an absolute hardware ceiling; attempting to set an interface MTU higher than the supported system limit will cause the switch CLI to reject the command.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_Guide_Configuring_Interface_MTU_on_Cisco_Catalyst_IOS-XE\"><\/span>Step-by-Step Guide: Configuring Interface MTU on Cisco Catalyst (IOS-XE)<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Modern Cisco Catalyst 9000 switches running Cisco IOS-XE allow you to configure MTU on physical switchports (Layer 2), routed ports (Layer 3), Port-Channels, and SVIs. Follow these steps to apply interface-specific MTU settings.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Enter_Global_Configuration_Mode\"><\/span>Step 1: Enter Global Configuration Mode<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Log in to the switch and enter privileged EXEC mode, then move to global configuration:<\/p>\n<pre><code class=\"language-text\">Switch# configure terminal\nSwitch(config)#\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Configure_MTU_on_a_Layer_2_Switchport_Access_or_Trunk\"><\/span>Step 2: Configure MTU on a Layer 2 Switchport (Access or Trunk)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To configure MTU on a switched interface (either access or trunk mode), apply the <code>mtu<\/code> command directly under the physical interface:<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface GigabitEthernet 1\/0\/1\nSwitch(config-if)# description Storage-Host-Trunk\nSwitch(config-if)# switchport mode trunk\nSwitch(config-if)# mtu 9000\nSwitch(config-if)# exit\n<\/code><\/pre>\n<p><em>Note: On IOS-XE 17.1.1 and later, changing the MTU on a standalone physical port does not cause the link to flap.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Configure_MTU_on_a_Layer_3_Routed_Port\"><\/span>Step 3: Configure MTU on a Layer 3 Routed Port<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>For routed physical interfaces (configured with <code>no switchport<\/code>), you can configure the interface MTU as well as protocol-specific MTUs (such as <code>ip mtu<\/code> or <code>ipv6 mtu<\/code>):<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface GigabitEthernet 1\/0\/2\nSwitch(config-if)# description Routed-Uplink-to-Core\nSwitch(config-if)# no switchport\nSwitch(config-if)# ip address 10.10.10.1 255.255.255.0\nSwitch(config-if)# mtu 9000\nSwitch(config-if)# ip mtu 9000\nSwitch(config-if)# exit\n<\/code><\/pre>\n<p><em>Note: If both <code>mtu<\/code> and <code>ip mtu<\/code> are configured, <code>ip mtu<\/code> sets the IP packet fragmentation boundary, which cannot exceed the physical <code>mtu<\/code> value.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Configure_MTU_on_a_Switched_Virtual_Interface_SVI\"><\/span>Step 4: Configure MTU on a Switched Virtual Interface (SVI)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To support jumbo frames routed across a VLAN, update the MTU on the corresponding SVI (VLAN interface):<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface Vlan 100\nSwitch(config-if)# description iSCSI-VLAN-Gateway\nSwitch(config-if)# ip address 192.168.100.1 255.255.255.0\nSwitch(config-if)# mtu 9000\nSwitch(config-if)# ip mtu 9000\nSwitch(config-if)# exit\n<\/code><\/pre>\n<p><em>Note: Increasing the MTU on an SVI will not pass jumbo frames unless all underlying physical Layer 2 switchports carrying that VLAN are also configured to support that MTU size.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Configure_MTU_on_a_Port-Channel_EtherChannel\"><\/span>Step 5: Configure MTU on a Port-Channel (EtherChannel)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When configuring an EtherChannel, apply the MTU setting directly to the logical <code>Port-channel<\/code> interface:<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface Port-channel 1\nSwitch(config-if)# mtu 9000\nSwitch(config-if)# exit\n<\/code><\/pre>\n<p>IOS-XE automatically propagates the MTU setting from the logical Port-Channel interface to all active physical bundle members. If the bundle runs dynamic LACP or PAgP, the port-channel interface will momentarily flap during the MTU update to negotiate new parameters.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_6_Save_the_Configuration\"><\/span>Step 6: Save the Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Exit configuration mode and write the active running configuration to NVRAM:<\/p>\n<pre><code class=\"language-text\">Switch(config)# end\nSwitch# write memory\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"CLI_Configuration_Templates_for_Bulk_MTU_Changes\"><\/span>CLI Configuration Templates for Bulk MTU Changes<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When provisioning a switch for hypervisor clusters, SAN environments, or core uplinks, configuring interfaces individually is inefficient. Use these ready-to-deploy templates to apply MTU settings across multiple interfaces simultaneously.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Template_1_Bulk_Physical_AccessTrunk_Ports_Using_Interface_Range\"><\/span>Template 1: Bulk Physical Access\/Trunk Ports Using Interface Range<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Applies a 9000-byte jumbo MTU to an entire block of physical ports:<\/p>\n<pre><code class=\"language-text\">! --- Apply Jumbo MTU across contiguous ports ---\nconfigure terminal\ninterface range GigabitEthernet 1\/0\/1 - 24\n description Hypervisor-Host-Facing-Ports\n mtu 9000\nexit\nend\nwrite memory\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Template_2_Core_Infrastructure_Uplink_Trunks_Port-Channels_and_SVIs\"><\/span>Template 2: Core Infrastructure (Uplink Trunks, Port-Channels, and SVIs)<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Sets jumbo MTU across multiple uplinks, aggregated links, and routed VLAN interfaces:<\/p>\n<pre><code class=\"language-text\">! --- Bulk Core Uplink and SVI MTU Template ---\nconfigure terminal\n\n! Apply to multiple Port-Channels\ninterface range Port-channel 1 - 4\n mtu 9216\nexit\n\n! Apply to routed VLAN interfaces\ninterface range Vlan 10, Vlan 20, Vlan 30, Vlan 40\n mtu 9000\n ip mtu 9000\nexit\n\nend\nwrite memory\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Template_3_Global_System_Baseline_MTU_Configuration\"><\/span>Template 3: Global System Baseline MTU Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Sets the global default MTU to jumbo across all interfaces on the switch, removing the need for per-port configurations on devices where all traffic should default to jumbo frames:<\/p>\n<pre><code class=\"language-text\">! --- Global Switch System MTU Configuration ---\nconfigure terminal\nsystem mtu 9000\nend\nwrite memory\n<\/code><\/pre>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Verifying_MTU_Settings_and_Testing_Jumbo_Frames\"><\/span>Verifying MTU Settings and Testing Jumbo Frames<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>After applying MTU changes, verify that the switch hardware and the operational control plane reflect the new settings, and perform end-to-end packet validation.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Verify_Configured_MTU_on_Interfaces\"><\/span>Step 1: Verify Configured MTU on Interfaces<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On Cisco IOS-XE switches, verify interface MTUs using <code>show interface mtu<\/code> or by targeting specific ports:<\/p>\n<pre><code class=\"language-text\">Switch# show interface mtu\n\nPort         Name                     MTU\nGi1\/0\/1      Storage-Host-Trunk       9000\nGi1\/0\/2      Routed-Uplink-to-Core    9000\nPo1          Core-Interconnect        9216\nVl100        iSCSI-VLAN-Gateway       9000\n<\/code><\/pre>\n<p>To view the complete operational status of a single port, including Layer 2 and IP MTUs, filter the interface output:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces GigabitEthernet 1\/0\/1 | include MTU\n  MTU 9000 bytes, BW 1000000 Kbit\/sec, DLY 10 usec, reliability 255\/255, txload 1\/255, rxload 1\/255\n\nSwitch# show ip interface GigabitEthernet 1\/0\/2 | include MTU\n  MTU is 9000 bytes\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Validate_End-to-End_MTU_with_Do-Not-Fragment_DF_Pings\"><\/span>Step 2: Validate End-to-End MTU with Do-Not-Fragment (DF) Pings<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>A show command only validates local switch configuration; it does not guarantee that every intermediate hop, firewall, or remote endpoint supports that frame size. To test end-to-end MTU capacity, execute an ICMP ping with the <strong>Do Not Fragment (DF)<\/strong> bit set.<\/p>\n<h4>Testing from Cisco IOS-XE CLI<\/h4>\n<p>In Cisco IOS and IOS-XE, the <code>size<\/code> argument defines the <strong>total IP packet size<\/strong> (IP header + ICMP header + payload):<\/p>\n<pre><code class=\"language-text\">Switch# ping 10.10.10.2 size 9000 df-bit\nType escape sequence to abort.\nSending 5, 9000-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:\nPacket sent with the \/Dont Fragment\/ bit set\n!!!!!\nSuccess rate is 100 percent (5\/5), round-trip min\/avg\/max = 1\/2\/3 ms\n<\/code><\/pre>\n<p>If any link along the path cannot accommodate 9000 bytes, the switch output displays <code>M<\/code> (fragmentation needed and DF set) or drops:<\/p>\n<pre><code class=\"language-text\">Switch# ping 10.10.10.2 size 9000 df-bit\nSending 5, 9000-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:\nPacket sent with the \/Dont Fragment\/ bit set\n.....\nSuccess rate is 0 percent (0\/5)\n<\/code><\/pre>\n<h4>Testing from Connected Hosts (Windows and Linux)<\/h4>\n<p>Unlike Cisco CLI, host operating system ping tools specify only the <strong>ICMP payload size<\/strong>, excluding the 20-byte IP header and 8-byte ICMP header (28 bytes total). To test for a 9000-byte MTU, send a payload of <strong>8972 bytes<\/strong> (8972 + 28 = 9000):<\/p>\n<ul>\n<li>\n<p><strong>Microsoft Windows:<\/strong><br \/>\n  <code>cmd<br \/>\n  ping -f -l 8972 10.10.10.2<\/code><br \/>\n  <em>(Parameter <code>-f<\/code> sets the DF bit; <code>-l<\/code> specifies buffer length.)<\/em><\/p>\n<\/li>\n<li>\n<p><strong>Linux:<\/strong><br \/>\n  <code>bash<br \/>\n  ping -M do -s 8972 10.10.10.2<\/code><br \/>\n  <em>(Parameter <code>-M do<\/code> prohibits fragmentation; <code>-s<\/code> sets payload size.)<\/em><\/p>\n<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Troubleshooting_MTU_Mismatches_and_OSPF_EXSTART_Hangs\"><\/span>Troubleshooting MTU Mismatches and OSPF EXSTART Hangs<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Mismatched MTUs are among the most common root causes of routing instability and silent packet loss. When two directly connected devices do not share identical MTU values, critical control-plane and data-plane failures occur.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Issue_1_OSPF_Adjacency_Stuck_in_EXSTART_EXCHANGE\"><\/span>Issue 1: OSPF Adjacency Stuck in EXSTART \/ EXCHANGE<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When forming an adjacency over an interface, OSPF routers transition through <code>EXSTART<\/code> and <code>EXCHANGE<\/code> states, where they determine master\/slave roles and exchange Database Description (DBD) packets. Under RFC 2328, each router advertises its local interface MTU in the DBD packet.<\/p>\n<pre><code class=\"language-text\">Router-A (MTU 9000) &lt;--------------------------&gt; Router-B (MTU 1500)\n                    --- DBD (MTU: 9000) ---&gt;\n                    &lt;--- DBD (MTU: 1500) ---\n<\/code><\/pre>\n<p>If Router A has an MTU of 9000 and Router B has an MTU of 1500:<br \/>\n1. Router B receives Router A&#8217;s DBD packet advertising an MTU of 9000. Because 9000 exceeds Router B&#8217;s local MTU (1500), Router B rejects the packet and refuses to proceed.<br \/>\n2. Router A keeps retransmitting its DBD packet because Router B never acknowledges it.<br \/>\n3. The neighbor state remains permanently trapped in <code>EXSTART\/EXCHANGE<\/code>.<\/p>\n<h4>Step-by-Step Resolution<\/h4>\n<ol>\n<li>Verify the neighbor state and identify the stuck interface:<br \/>\n   <code>text<br \/>\n   Switch# show ip ospf neighbor<br \/>\n   Neighbor ID     Pri   State           Dead Time   Address         Interface<br \/>\n   192.168.1.2       1   EXSTART\/DR      00:00:34    10.10.10.2      GigabitEthernet1\/0\/2<\/code><\/li>\n<li>Enable OSPF adjacency debugging to confirm the MTU mismatch:<br \/>\n   <code>text<br \/>\n   Switch# debug ip ospf adj<br \/>\n   OSPF: Rcv DBD from 192.168.1.2 on GigabitEthernet1\/0\/2 with larger MTU 9000 (local MTU 1500)<br \/>\n   OSPF: Mismatched MTU, DBD packet dropped<\/code><\/li>\n<li>Correct the MTU on the mismatched interface so that both peers align:<br \/>\n   <code>text<br \/>\n   Switch(config)# interface GigabitEthernet 1\/0\/2<br \/>\n   Switch(config-if)# mtu 9000<br \/>\n   Switch(config-if)# ip mtu 9000<\/code><\/li>\n<li><strong>Temporary Emergency Workaround:<\/strong> If you cannot immediately change the MTU on one side due to administrative constraints, disable OSPF MTU negotiation on the interface:<br \/>\n   <code>text<br \/>\n   Switch(config-if)# ip ospf mtu-ignore<\/code><br \/>\n   <em>Caution: <code>ip ospf mtu-ignore<\/code> should only be used as a temporary workaround. While it allows OSPF to achieve a <code>FULL<\/code> state, any subsequent Link State Update (LSU) packet larger than 1500 bytes will be silently dropped by the lower-MTU peer, causing inconsistent routing tables.<\/em><\/li>\n<\/ol>\n<h3><span class=\"ez-toc-section\" id=\"Issue_2_Data-Plane_Packet_Drops_and_Giant_Counters\"><\/span>Issue 2: Data-Plane Packet Drops and &#8220;Giant&#8221; Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When an upstream switch or server transmits a 9000-byte frame into a switchport configured for 1500 bytes, the ingress switch hardware discards the frame as an invalid size.<\/p>\n<h4>Diagnostic Steps:<\/h4>\n<ol>\n<li>Check the physical interface counters for dropped packets and errors:<br \/>\n   <code>text<br \/>\n   Switch# show interfaces GigabitEthernet 1\/0\/1 | include giants|input errors|CRC<br \/>\n        14285 input errors, 14285 giants, 0 CRC, 0 frame<\/code><\/li>\n<li>A non-zero, continuously incrementing <strong>giants<\/strong> counter confirms that incoming frames exceed the configured interface MTU.<\/li>\n<li>Resolve the drop condition by raising the interface MTU to match the transmitting device:<br \/>\n   <code>text<br \/>\n   Switch(config)# interface GigabitEthernet 1\/0\/1<br \/>\n   Switch(config-if)# mtu 9216<\/code><\/li>\n<\/ol>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_Catalyst_vs_Nexus_NX-OS_MTU_Configuration_Differences\"><\/span>Cisco Catalyst vs. Nexus (NX-OS) MTU Configuration Differences<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>While Catalyst switches handle MTU via straightforward interface commands or global system defaults, Cisco Nexus data center switches running NX-OS use different architectural workflows depending on the hardware platform.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Architectural Feature<\/th>\n<th style=\"text-align: left;\">Cisco Catalyst (IOS \/ IOS-XE)<\/th>\n<th style=\"text-align: left;\">Cisco Nexus (NX-OS)<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>Primary OS<\/strong><\/td>\n<td style=\"text-align: left;\">Cisco IOS-XE (Catalyst 9000 \/ 3850)<\/td>\n<td style=\"text-align: left;\">Cisco NX-OS (Nexus 3000 \/ 5000 \/ 7000 \/ 9000)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Default L2 \/ L3 MTU<\/strong><\/td>\n<td style=\"text-align: left;\">1500 bytes<\/td>\n<td style=\"text-align: left;\">1500 bytes<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Maximum Supported Jumbo<\/strong><\/td>\n<td style=\"text-align: left;\">Up to 9216 bytes (Platform-dependent)<\/td>\n<td style=\"text-align: left;\">Up to 9216 bytes<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Layer 2 MTU Configuration<\/strong><\/td>\n<td style=\"text-align: left;\">Per-port <code>mtu &lt;bytes&gt;<\/code> directly under interface<\/td>\n<td style=\"text-align: left;\">System-wide via <code>policy-map type network-qos<\/code> (N5k\/N6k\/older N3k) OR per-port <code>mtu 9216<\/code> (N7k\/N9k)<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Layer 3 MTU Configuration<\/strong><\/td>\n<td style=\"text-align: left;\"><code>mtu<\/code> and <code>ip mtu<\/code> under routed port \/ SVI<\/td>\n<td style=\"text-align: left;\"><code>mtu &lt;bytes&gt;<\/code> under routed port \/ SVI<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Global Baseline Command<\/strong><\/td>\n<td style=\"text-align: left;\"><code>system mtu &lt;bytes&gt;<\/code><\/td>\n<td style=\"text-align: left;\"><code>system jumbomtu &lt;bytes&gt;<\/code><\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Reboot Required?<\/strong><\/td>\n<td style=\"text-align: left;\">No on modern IOS-XE; Yes on legacy classic IOS<\/td>\n<td style=\"text-align: left;\">Never requires a reboot<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Verification Command<\/strong><\/td>\n<td style=\"text-align: left;\"><code>show interface mtu<\/code><br \/><code>show interfaces &lt;id&gt; \\| inc MTU<\/code><\/td>\n<td style=\"text-align: left;\"><code>show interface &lt;id&gt; \\| inc MTU<\/code><br \/><code>show queuing interface &lt;id&gt;<\/code><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3><span class=\"ez-toc-section\" id=\"The_NX-OS_Network-QoS_Difference\"><\/span>The NX-OS Network-QoS Difference<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>On traditional Nexus switches (such as Nexus 5000, 5500, 6000, and fixed 3000 series), Layer 2 jumbo frames cannot be configured on individual interfaces. Instead, the administrator must configure a global Quality of Service policy map:<\/p>\n<pre><code class=\"language-text\">! --- Nexus 5000\/6000 Global QoS Jumbo MTU Configuration ---\nNexus-5K(config)# policy-map type network-qos jumbo\nNexus-5K(config-pmap-nq)# class type network-qos class-default\nNexus-5K(config-pmap-c-nq)# mtu 9216\nNexus-5K(config-pmap-c-nq)# exit\nNexus-5K(config-pmap-nq)# exit\nNexus-5K(config)# system qos\nNexus-5K(config-sys-qos)# service-policy type network-qos jumbo\n<\/code><\/pre>\n<p>On modern Nexus 9000 switches running NX-OS in standalone mode, Cisco brought the interface behavior in line with Catalyst switches, allowing engineers to apply <code>mtu 9216<\/code> directly to Layer 2 and Layer 3 interfaces.<\/p>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_Catalyst_MTU_Technical_Reference_and_Command_Specifications\"><\/span>Cisco Catalyst MTU Technical Reference and Command Specifications<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<h3><span class=\"ez-toc-section\" id=\"MTU_Framing_and_Wire_Overhead\"><\/span>MTU Framing and Wire Overhead<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>When planning an MTU strategy, differentiate between Layer 3 packet size and the total Layer 2 Ethernet frame size transmitted onto the physical medium. <\/p>\n<pre><code class=\"language-text\">+-------------------------------------------------------------------------------+\n|                      Layer 2 Ethernet Frame (1518 - 9238 bytes)               |\n+-------------------+---------------+-----------------------+-------------------+\n|  Ethernet Header  | 802.1Q Tag    |   IP Packet (MTU)     | Frame Check (FCS) |\n|     (14 Bytes)    | (4 Bytes opt) | (1500 - 9216 Bytes)   |     (4 Bytes)     |\n+-------------------+---------------+-----------------------+-------------------+\n<\/code><\/pre>\n<ul>\n<li><strong>Standard Ethernet Frame:<\/strong> 1500 (IP MTU) + 14 (MAC header) + 4 (FCS) = <strong>1518 bytes<\/strong>.<\/li>\n<li><strong>Standard 802.1Q Tagged Frame:<\/strong> 1500 (IP MTU) + 14 (MAC header) + 4 (VLAN tag) + 4 (FCS) = <strong>1522 bytes<\/strong>.<\/li>\n<li><strong>Jumbo Ethernet Frame (9000):<\/strong> 9000 (IP MTU) + 14 (MAC header) + 4 (FCS) = <strong>9018 bytes<\/strong> (or <strong>9022 bytes<\/strong> with 802.1Q tagging).<\/li>\n<li><strong>Maximum Platform Frame (9216):<\/strong> 9216 (IP MTU) + 14 (MAC header) + 4 (FCS) = <strong>9234 bytes<\/strong> (or <strong>9238 bytes<\/strong> with 802.1Q tagging).<\/li>\n<\/ul>\n<p><em>Note: Cisco Catalyst switches define the <code>mtu<\/code> command as the <\/em><em>Layer 3 payload size (IP MTU)<\/em><em>. The switch automatically adjusts the Layer 2 frame admission hardware to accommodate the required MAC headers and tags without manual overhead calculations.<\/em><\/p>\n<h3><span class=\"ez-toc-section\" id=\"Platform_Support_Specifications\"><\/span>Platform Support Specifications<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Catalyst 9200 Series:<\/strong> Supports system-wide and per-port MTU up to <strong>9216 bytes<\/strong>.<\/li>\n<li><strong>Catalyst 9300 \/ 9400 \/ 9500 \/ 9600 Series:<\/strong> Supports system-wide and per-port MTU up to <strong>9216 bytes<\/strong> across all Ethernet port types.<\/li>\n<li><strong>Minimum IPv6 MTU:<\/strong> Enforced across all Catalyst 9000 switches at <strong>1280 bytes<\/strong> in adherence to RFC 8200.<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Command_Reference\"><\/span>Command Reference<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<h4><code>system mtu &lt;1500-9216&gt;<\/code><\/h4>\n<ul>\n<li><strong>Mode:<\/strong> Global Configuration<\/li>\n<li><strong>Description:<\/strong> Configures the global default MTU applied to all interfaces that do not have an explicit per-port MTU configuration.<\/li>\n<li><strong>Default:<\/strong> 1500 bytes.<\/li>\n<\/ul>\n<h4><code>mtu &lt;1500-9216&gt;<\/code><\/h4>\n<ul>\n<li><strong>Mode:<\/strong> Interface Configuration (Physical, Port-Channel, SVI)<\/li>\n<li><strong>Description:<\/strong> Sets the maximum transmission unit size for switched or routed traffic passing through the interface.<\/li>\n<li><strong>Default:<\/strong> Inherits global <code>system mtu<\/code> (1500 bytes).<\/li>\n<\/ul>\n<h4><code>ip mtu &lt;68-9216&gt;<\/code><\/h4>\n<ul>\n<li><strong>Mode:<\/strong> Interface Configuration (Routed port or SVI)<\/li>\n<li><strong>Description:<\/strong> Sets the IP packet size before Layer 3 fragmentation occurs. Must be less than or equal to the interface <code>mtu<\/code>.<\/li>\n<\/ul>\n<h4><code>show interface mtu<\/code><\/h4>\n<ul>\n<li><strong>Mode:<\/strong> Privileged EXEC<\/li>\n<li><strong>Description:<\/strong> Displays a consolidated table of all configured and operational MTUs across all switchports on the device.<\/li>\n<\/ul>\n<hr \/>\n<h2><span class=\"ez-toc-section\" id=\"Conclusion\"><\/span>Conclusion<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Changing the MTU on a Cisco switch interface requires aligning your configuration method with the platform\u2019s underlying operating system. On modern Catalyst switches running Cisco IOS-XE, per-port MTU allows seamless changes without service interruptions or reboots. For consistent performance, ensure that every device along the end-to-end data path\u2014from host NICs to intermediate switches, routers, and firewalls\u2014shares an identical MTU. Finally, always validate real-world forwarding using extended pings with the Do Not Fragment (DF) bit set to confirm seamless transport for standard and jumbo traffic alike.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-change-mtu-on-cisco-switch-interface_24482.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Change+MTU+on+Cisco+Switch+Interface+https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\",\"How to Change MTU on Cisco Switch Interface\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Maximum Transmission Unit (MTU) defines the maximum size of a packet or frame\u2014measured in bytes\u2014that a network interface can process and forward without fragmenting it. In enterprise and data center networks, adjusting the MTU beyond the standard Ethernet size of 1500 bytes to accommodate jumbo frames (typically up to 9000 or 9216 bytes) is essential&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Change MTU on Cisco Switch Interface - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Change MTU on Cisco Switch Interface - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Maximum Transmission Unit (MTU) defines the maximum size of a packet or frame\u2014measured in bytes\u2014that a network interface can process and forward without fragmenting it. In enterprise and data center networks, adjusting the MTU beyond the standard Ethernet size of 1500 bytes to accommodate jumbo frames (typically up to 9000 or 9216 bytes) is essential... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-16T02:44:30+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"12 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\",\"name\":\"How to Change MTU on Cisco Switch Interface - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-16T02:44:30+00:00\",\"dateModified\":\"2026-11-16T02:44:30+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Change MTU on Cisco Switch Interface\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Change MTU on Cisco Switch Interface\",\"datePublished\":\"2026-11-16T02:44:30+00:00\",\"dateModified\":\"2026-11-16T02:44:30+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage\"},\"wordCount\":1935,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Change MTU on Cisco Switch Interface - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html","og_locale":"en_US","og_type":"article","og_title":"How to Change MTU on Cisco Switch Interface - SPOTO Official Blog","og_description":"Maximum Transmission Unit (MTU) defines the maximum size of a packet or frame\u2014measured in bytes\u2014that a network interface can process and forward without fragmenting it. In enterprise and data center networks, adjusting the MTU beyond the standard Ethernet size of 1500 bytes to accommodate jumbo frames (typically up to 9000 or 9216 bytes) is essential... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-16T02:44:30+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"12 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html","name":"How to Change MTU on Cisco Switch Interface - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-16T02:44:30+00:00","dateModified":"2026-11-16T02:44:30+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Change MTU on Cisco Switch Interface"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Change MTU on Cisco Switch Interface","datePublished":"2026-11-16T02:44:30+00:00","dateModified":"2026-11-16T02:44:30+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#webpage"},"wordCount":1935,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-change-mtu-on-cisco-switch-interface_24482.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24482"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24482"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24482\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24482"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24482"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24482"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}