{"id":24478,"date":"2026-11-16T10:36:38","date_gmt":"2026-11-16T02:36:38","guid":{"rendered":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html"},"modified":"2026-11-16T10:36:38","modified_gmt":"2026-11-16T02:36:38","slug":"how-to-change-duplex-in-cisco-switch","status":"publish","type":"post","link":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html","title":{"rendered":"How to Change Duplex in Cisco Switch"},"content":{"rendered":"<p>Ethernet interfaces operate in either half-duplex or full-duplex mode. In half-duplex mode, an interface cannot send and receive data at the same time, relying on Carrier Sense Multiple Access with Collision Detection (CSMA\/CD) to manage link contention. In full-duplex mode, dedicated transmit and receive paths eliminate collisions entirely, effectively doubling total potential bandwidth.<\/p>\n<p>While modern network infrastructure relies on IEEE auto-negotiation to detect link speed and duplex automatically, network administrators still encounter legacy hardware, specialized industrial systems, or misconfigured links that require manual intervention. Understanding how to configure, audit, and troubleshoot interface duplex settings in Cisco IOS is fundamental to maintaining a high-performance, collision-free local network.<\/p>\n<div id=\"ez-toc-container\" class=\"ez-toc-v2_0_17 counter-hierarchy counter-decimal ez-toc-light-blue\">\n<div class=\"ez-toc-title-container\">\n<p class=\"ez-toc-title\">Table of Contents<\/p>\n<span class=\"ez-toc-title-toggle\"><a class=\"ez-toc-pull-right ez-toc-btn ez-toc-btn-xs ez-toc-btn-default ez-toc-toggle\" style=\"display: none;\"><i class=\"ez-toc-glyphicon ez-toc-icon-toggle\"><\/i><\/a><\/span><\/div>\n<nav><ul class=\"ez-toc-list ez-toc-list-level-1\"><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-1\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Auto-Negotiation_vs_Hardcoded_Duplex_Best_Practices\" title=\"Auto-Negotiation vs. Hardcoded Duplex Best Practices\">Auto-Negotiation vs. Hardcoded Duplex Best Practices<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-2\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Cisco_IOS_Speed_and_Duplex_Command_Reference\" title=\"Cisco IOS Speed and Duplex Command Reference\">Cisco IOS Speed and Duplex Command Reference<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-3\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Command_Syntax\" title=\"Command Syntax\">Command Syntax<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-4\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Parameter_Definitions\" title=\"Parameter Definitions\">Parameter Definitions<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-5\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Command_Scope_and_Defaults\" title=\"Command Scope and Defaults\">Command Scope and Defaults<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-6\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step-by-Step_Guide_How_to_Configure_Duplex_and_Speed_on_a_Switch_Port\" title=\"Step-by-Step Guide: How to Configure Duplex and Speed on a Switch Port\">Step-by-Step Guide: How to Configure Duplex and Speed on a Switch Port<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-7\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_1_Enter_Privileged_EXEC_and_Global_Configuration_Mode\" title=\"Step 1: Enter Privileged EXEC and Global Configuration Mode\">Step 1: Enter Privileged EXEC and Global Configuration Mode<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-8\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_2_Select_the_Target_Interface\" title=\"Step 2: Select the Target Interface\">Step 2: Select the Target Interface<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-9\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_3_Configure_Speed_and_Duplex_Parameters\" title=\"Step 3: Configure Speed and Duplex Parameters\">Step 3: Configure Speed and Duplex Parameters<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-10\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_4_Return_to_Privileged_EXEC_Mode\" title=\"Step 4: Return to Privileged EXEC Mode\">Step 4: Return to Privileged EXEC Mode<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-11\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_5_Verify_Interface_State_and_Operational_Settings\" title=\"Step 5: Verify Interface State and Operational Settings\">Step 5: Verify Interface State and Operational Settings<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-12\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_6_Save_the_Configuration\" title=\"Step 6: Save the Configuration\">Step 6: Save the Configuration<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-13\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Batch_Port_Configuration_Template\" title=\"Batch Port Configuration Template\">Batch Port Configuration Template<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-14\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Reusable_Interface_Range_Script\" title=\"Reusable Interface Range Script\">Reusable Interface Range Script<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-15\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Frequently_Asked_Questions_Why_Is_the_Duplex_Command_Missing_or_Unrecognized\" title=\"Frequently Asked Questions: Why Is the Duplex Command Missing or Unrecognized?\">Frequently Asked Questions: Why Is the Duplex Command Missing or Unrecognized?<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-16\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Why_is_the_duplex_command_missing_on_10G_40G_and_100G_interfaces\" title=\"Why is the duplex command missing on 10G, 40G, and 100G interfaces?\">Why is the duplex command missing on 10G, 40G, and 100G interfaces?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-17\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Why_does_a_Gigabit_SFP_fiber_port_reject_manual_duplex_settings\" title=\"Why does a Gigabit SFP fiber port reject manual duplex settings?\">Why does a Gigabit SFP fiber port reject manual duplex settings?<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-18\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Why_does_Cisco_IOS_reject_duplex_half_on_a_Gigabit_Ethernet_copper_port\" title=\"Why does Cisco IOS reject duplex half on a Gigabit Ethernet copper port?\">Why does Cisco IOS reject duplex half on a Gigabit Ethernet copper port?<\/a><\/li><\/ul><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-2\"><a class=\"ez-toc-link ez-toc-heading-19\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Diagnosing_and_Resolving_Duplex_Mismatch_Errors\" title=\"Diagnosing and Resolving Duplex Mismatch Errors\">Diagnosing and Resolving Duplex Mismatch Errors<\/a><ul class=\"ez-toc-list-level-3\"><li class=\"ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-20\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_1_Detect_the_Cisco_Discovery_Protocol_CDP_Error_Log\" title=\"Step 1: Detect the Cisco Discovery Protocol (CDP) Error Log\">Step 1: Detect the Cisco Discovery Protocol (CDP) Error Log<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-21\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_2_Analyze_Interface_Collision_and_Frame_Error_Counters\" title=\"Step 2: Analyze Interface Collision and Frame Error Counters\">Step 2: Analyze Interface Collision and Frame Error Counters<\/a><\/li><li class=\"ez-toc-page-1 ez-toc-heading-level-3\"><a class=\"ez-toc-link ez-toc-heading-22\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\/#Step_3_Implement_the_Remediation_Workflow\" title=\"Step 3: Implement the Remediation Workflow\">Step 3: Implement the Remediation Workflow<\/a><\/li><\/ul><\/li><\/ul><\/nav><\/div>\n<h2><span class=\"ez-toc-section\" id=\"Auto-Negotiation_vs_Hardcoded_Duplex_Best_Practices\"><\/span>Auto-Negotiation vs. Hardcoded Duplex Best Practices<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Before manually altering port parameters, it is critical to evaluate whether manual overrides align with IEEE Ethernet standards. Under IEEE 802.3u (Fast Ethernet) and IEEE 802.3ab (Gigabit Ethernet), auto-negotiation manages speed, duplex, and flow control between two link partners through exchange of Fast Link Pulses (FLPs).<\/p>\n<p>When an administrator forces one side of a link to Full Duplex while leaving the connected device on Auto, the auto-negotiating device falls back to <strong>parallel detection<\/strong>. Parallel detection can successfully determine the link speed (such as 100 Mbps) from incoming electrical signals, but it cannot negotiate duplex without active FLP communication. As defined by the IEEE specification, when duplex cannot be negotiated, the device must default to <strong>half-duplex<\/strong>. This creates an asymmetric link state known as a duplex mismatch.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left;\">Evaluation Criteria<\/th>\n<th style=\"text-align: left;\">Auto-Negotiation (Recommended)<\/th>\n<th style=\"text-align: left;\">Hardcoded Full Duplex<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"text-align: left;\"><strong>IEEE Standard Compliance<\/strong><\/td>\n<td style=\"text-align: left;\">Fully compliant with IEEE 802.3u, 802.3ab, and 802.3an<\/td>\n<td style=\"text-align: left;\">Bypasses standard negotiation exchange<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Gigabit (1000BASE-T) Compatibility<\/strong><\/td>\n<td style=\"text-align: left;\">Mandatory for clock synchronization and master\/slave role setup<\/td>\n<td style=\"text-align: left;\">Not recommended; forcing speed\/duplex can break clock negotiation<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>10G \/ 40G \/ 100G Interfaces<\/strong><\/td>\n<td style=\"text-align: left;\">Auto-negotiates capability and flow control<\/td>\n<td style=\"text-align: left;\">Inapplicable; multi-gigabit interfaces run full-duplex natively<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Duplex Mismatch Vulnerability<\/strong><\/td>\n<td style=\"text-align: left;\">Near zero when both sides support auto-negotiation<\/td>\n<td style=\"text-align: left;\">High if the opposing link partner is left on auto<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Cisco Best Practice Status<\/strong><\/td>\n<td style=\"text-align: left;\">Standard default for all switch-to-switch and switch-to-host links<\/td>\n<td style=\"text-align: left;\">Reserved strictly for legacy devices that fail auto-negotiation<\/td>\n<\/tr>\n<tr>\n<td style=\"text-align: left;\"><strong>Operational Overhead<\/strong><\/td>\n<td style=\"text-align: left;\">Zero manual reconfiguration during device swaps<\/td>\n<td style=\"text-align: left;\">High; requires manual audit of both link endpoints<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Core Rule:<\/strong> Either configure <strong>both<\/strong> link endpoints to <code>auto<\/code>, or manually lock <strong>both<\/strong> endpoints to identical speed and duplex settings. Never hardcode one side while leaving the other on auto.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Cisco_IOS_Speed_and_Duplex_Command_Reference\"><\/span>Cisco IOS Speed and Duplex Command Reference<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>Cisco IOS and IOS-XE provide native interface-level keywords to define physical-layer characteristics. Below are the standard command definitions and defaults for Fast Ethernet and Gigabit Ethernet switchports.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Command_Syntax\"><\/span>Command Syntax<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">Switch(config-if)# duplex {auto | full | half}\nSwitch(config-if)# speed {auto | 10 | 100 | 1000}\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Parameter_Definitions\"><\/span>Parameter Definitions<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><code>duplex auto<\/code>: Enables IEEE auto-negotiation of duplex mode. This is the factory-default setting on all modular and fixed-configuration Cisco Catalyst switches.<\/li>\n<li><code>duplex full<\/code>: Forces the port to operate strictly in full-duplex mode. Disables CSMA\/CD collision detection mechanisms on the interface.<\/li>\n<li><code>duplex half<\/code>: Forces the port to operate in half-duplex mode. Enables CSMA\/CD mechanisms to detect and back off from concurrent frame transmissions.<\/li>\n<li><code>speed auto<\/code>: Enables auto-negotiation of port transmission rate.<\/li>\n<li><code>speed {10 | 100 | 1000}<\/code>: Statically sets the transmission clock rate to 10 Mbps, 100 Mbps, or 1000 Mbps (Gigabit).<\/li>\n<\/ul>\n<h3><span class=\"ez-toc-section\" id=\"Command_Scope_and_Defaults\"><\/span>Command Scope and Defaults<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<ul>\n<li><strong>Default Mode:<\/strong> <code>speed auto<\/code> and <code>duplex auto<\/code><\/li>\n<li><strong>Configuration Context:<\/strong> Interface Configuration Mode (<code>config-if<\/code>) or Interface Range Configuration Mode (<code>config-if-range<\/code>)<\/li>\n<li><strong>Hardware Scope:<\/strong> Applies to standard copper RJ-45 interfaces (10\/100\/1000BASE-T). Most fiber SFP ports and interfaces running at 10 Gbps or higher do not support the <code>half<\/code> parameter.<\/li>\n<\/ul>\n<h2><span class=\"ez-toc-section\" id=\"Step-by-Step_Guide_How_to_Configure_Duplex_and_Speed_on_a_Switch_Port\"><\/span>Step-by-Step Guide: How to Configure Duplex and Speed on a Switch Port<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When manual assignment is required, execute the following commands in the Cisco IOS command-line interface (CLI).<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Enter_Privileged_EXEC_and_Global_Configuration_Mode\"><\/span>Step 1: Enter Privileged EXEC and Global Configuration Mode<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Log in to your Cisco switch via SSH or console cable, enter privileged EXEC mode, and proceed to global configuration mode:<\/p>\n<pre><code class=\"language-text\">Switch&gt; enable\nSwitch# configure terminal\nEnter configuration commands, one per line. End with CNTL\/Z.\nSwitch(config)#\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Select_the_Target_Interface\"><\/span>Step 2: Select the Target Interface<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Navigate into the specific port you need to adjust (e.g., GigabitEthernet 0\/1):<\/p>\n<pre><code class=\"language-text\">Switch(config)# interface GigabitEthernet 0\/1\nSwitch(config-if)#\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Configure_Speed_and_Duplex_Parameters\"><\/span>Step 3: Configure Speed and Duplex Parameters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If you are hardcoding the duplex mode, Cisco IOS generally requires you to hardcode the speed first, as setting one without the other can trigger immediate link flaps or negotiation errors.<\/p>\n<p>To hardcode to 100 Mbps Full Duplex:<\/p>\n<pre><code class=\"language-text\">Switch(config-if)# speed 100\nSwitch(config-if)# duplex full\n<\/code><\/pre>\n<p>To revert the interface back to Cisco and IEEE standard auto-negotiation:<\/p>\n<pre><code class=\"language-text\">Switch(config-if)# speed auto\nSwitch(config-if)# duplex auto\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_4_Return_to_Privileged_EXEC_Mode\"><\/span>Step 4: Return to Privileged EXEC Mode<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Exit the interface configuration hierarchy:<\/p>\n<pre><code class=\"language-text\">Switch(config-if)# end\nSwitch#\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_5_Verify_Interface_State_and_Operational_Settings\"><\/span>Step 5: Verify Interface State and Operational Settings<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Confirm both the administrative setting and the actual operational state of the port using <code>show interfaces status<\/code>:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces GigabitEthernet 0\/1 status\n\nPort      Name               Status       Vlan       Duplex  Speed Type\nGi0\/1     UPLINK_SRV         connected    10           full    100 10\/100\/1000BaseTX\n<\/code><\/pre>\n<p>For detailed physical layer statistics and duplex validation, inspect the full interface counter:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces GigabitEthernet 0\/1\nGigabitEthernet0\/1 is up, line protocol is up (connected)\n  Hardware is Gigabit Ethernet, address is 001c.5821.1201 (bia 001c.5821.1201)\n  Full-duplex, 100Mb\/s, media type is 10\/100\/1000BaseTX\n  input flow-control is off, output flow-control is unsupported\n  ...\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_6_Save_the_Configuration\"><\/span>Step 6: Save the Configuration<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Ensure your changes persist across switch reloads by saving the running configuration to the startup configuration stored in NVRAM:<\/p>\n<pre><code class=\"language-text\">Switch# write memory\nBuilding configuration...\n[OK]\n<\/code><\/pre>\n<h2><span class=\"ez-toc-section\" id=\"Batch_Port_Configuration_Template\"><\/span>Batch Port Configuration Template<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>When staging a switch deployment or migrating an entire bank of access ports, configuring ports individually is inefficient. Use the <code>interface range<\/code> macro to apply uniform duplex and speed configurations across contiguous or disjoint port groups.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Reusable_Interface_Range_Script\"><\/span>Reusable Interface Range Script<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<pre><code class=\"language-text\">! ============================================================\n! CISCO IOS BATCH PORT DUPLEX\/SPEED CONFIGURATION TEMPLATE\n! ============================================================\n\nconfigure terminal\n\n! Option A: Set contiguous port block to Auto\/Auto (Best Practice)\ninterface range GigabitEthernet 1\/0\/1 - 24\n description Access_User_Ports\n speed auto\n duplex auto\n no shutdown\nexit\n\n! Option B: Hardcode specific non-contiguous legacy server ports\n! Syntax uses commas to separate distinct ports or sub-ranges\ninterface range GigabitEthernet 1\/0\/25 , GigabitEthernet 1\/0\/27 - 28\n description Legacy_Industrial_Controller\n speed 100\n duplex full\n no shutdown\nexit\n\nend\nwrite memory\n<\/code><\/pre>\n<h2><span class=\"ez-toc-section\" id=\"Frequently_Asked_Questions_Why_Is_the_Duplex_Command_Missing_or_Unrecognized\"><\/span>Frequently Asked Questions: Why Is the Duplex Command Missing or Unrecognized?<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>During port configuration, administrators sometimes encounter an error where typing <code>duplex full<\/code> or <code>duplex half<\/code> returns an <code>% Unrecognized command<\/code> message or where the command is omitted from the contextual help list (<code>?<\/code>).<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_is_the_duplex_command_missing_on_10G_40G_and_100G_interfaces\"><\/span>Why is the <code>duplex<\/code> command missing on 10G, 40G, and 100G interfaces?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>The IEEE 802.3ae standard for 10 Gigabit Ethernet (and subsequent high-speed standards such as 40GbE and 100GbE) completely removed half-duplex support. Because half-duplex is physically and logically impossible on these high-speed links, Cisco IOS omits the <code>duplex<\/code> configuration CLI context entirely. These interfaces run full-duplex exclusively.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Why_does_a_Gigabit_SFP_fiber_port_reject_manual_duplex_settings\"><\/span>Why does a Gigabit SFP fiber port reject manual duplex settings?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>Optical interfaces (such as 1000BASE-SX, 1000BASE-LX, and 1000BASE-ZX) do not use copper Ethernet signaling. Optical transceivers transmit and receive over separate strands of glass and operate strictly at full duplex. On Cisco fiber ports, auto-negotiation governs link signaling rather than speed\/duplex selection. If an optical link fails to establish with a third-party device, do not attempt to force duplex; instead, disable negotiation using the interface command:<\/p>\n<pre><code class=\"language-text\">Switch(config-if)# speed nonegotiate\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Why_does_Cisco_IOS_reject_duplex_half_on_a_Gigabit_Ethernet_copper_port\"><\/span>Why does Cisco IOS reject <code>duplex half<\/code> on a Gigabit Ethernet copper port?<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>While IEEE 802.3ab technically includes an optional specification for half-duplex Gigabit Ethernet, modern switching silicon and network line cards rarely implement it. Attempting to assign <code>duplex half<\/code> on fixed Gigabit ports may be rejected by the CLI because the physical layer chip (PHY) cannot support half-duplex timing at 1000 Mbps.<\/p>\n<h2><span class=\"ez-toc-section\" id=\"Diagnosing_and_Resolving_Duplex_Mismatch_Errors\"><\/span>Diagnosing and Resolving Duplex Mismatch Errors<span class=\"ez-toc-section-end\"><\/span><\/h2>\n<p>A duplex mismatch occurs when one side of a point-to-point Ethernet link is configured for full duplex while the opposing side operates in half duplex. Because electrical carriers are still present, the physical link will show <strong>Up\/Up<\/strong>, masking the fault from basic physical inspection. However, as link utilization rises, data throughput plummets due to chronic retransmissions.<\/p>\n<h3><span class=\"ez-toc-section\" id=\"Step_1_Detect_the_Cisco_Discovery_Protocol_CDP_Error_Log\"><\/span>Step 1: Detect the Cisco Discovery Protocol (CDP) Error Log<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If CDP is enabled on both devices, Cisco IOS automatically identifies the configuration disparity and logs a high-priority system notification:<\/p>\n<pre><code class=\"language-text\">%CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet0\/1 (not full duplex), with Switch2 GigabitEthernet0\/1 (full duplex).\n<\/code><\/pre>\n<h3><span class=\"ez-toc-section\" id=\"Step_2_Analyze_Interface_Collision_and_Frame_Error_Counters\"><\/span>Step 2: Analyze Interface Collision and Frame Error Counters<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>If CDP is disabled or the opposing end is an unmanaged switch or non-Cisco host, inspect the interface counters using <code>show interfaces &lt;interface-id&gt;<\/code>:<\/p>\n<pre><code class=\"language-text\">Switch# show interfaces GigabitEthernet 0\/1\n  ...\n  542219 packets input, 68421021 bytes, 0 no buffer\n  Received 212 broadcasts (104 multicasts)\n  0 runts, 0 giants, 0 throttles\n  1821 input errors, 1422 CRC, 0 frame, 0 overrun, 0 ignored\n  0 watchdog, 104 multicast, 0 pause input\n  724110 packets output, 92101411 bytes, 0 underruns\n  0 output errors, 0 collisions, 0 interface resets\n  24121 late collisions, 0 deferred, 0 pause output\n<\/code><\/pre>\n<p>Evaluate which side of the link exhibits which error types:<\/p>\n<ol>\n<li><strong>The Half-Duplex Side:<\/strong> Displays high numbers of <strong>late collisions<\/strong>. In normal half-duplex CSMA\/CD operation, collisions are expected within the first 64 bytes of transmission (the slot time). A collision occurring <em>after<\/em> the 64-byte window is designated a &#8220;late collision.&#8221; Late collisions indicate that the remote partner (configured for full-duplex) transmitted at will, oblivious to the local device&#8217;s transmission in progress.<\/li>\n<li><strong>The Full-Duplex Side:<\/strong> Displays high numbers of <strong>FCS errors, CRC errors, input errors<\/strong>, and <strong>runts<\/strong> (frames smaller than 64 bytes). These malformed frames represent aborted half-duplex transmissions that were truncated when the half-duplex partner abruptly backed off upon detecting a collision.<\/li>\n<\/ol>\n<h3><span class=\"ez-toc-section\" id=\"Step_3_Implement_the_Remediation_Workflow\"><\/span>Step 3: Implement the Remediation Workflow<span class=\"ez-toc-section-end\"><\/span><\/h3>\n<p>To permanently fix the mismatch:<\/p>\n<ol>\n<li>Identify the administrative duplex setting of the remote host or switch.<\/li>\n<li>Align both interfaces to standard auto-negotiation:<br \/>\n   <code>text<br \/>\n   Switch(config)# interface GigabitEthernet 0\/1<br \/>\n   Switch(config-if)# speed auto<br \/>\n   Switch(config-if)# duplex auto<\/code><\/li>\n<li>If connecting to an unalterable legacy appliance requiring hardcoded settings, enter the local interface and set both speed and duplex to match the legacy device:<br \/>\n   <code>text<br \/>\n   Switch(config)# interface GigabitEthernet 0\/1<br \/>\n   Switch(config-if)# speed 100<br \/>\n   Switch(config-if)# duplex full<\/code><\/li>\n<li>Clear the port statistics to verify errors cease accumulating:<br \/>\n   <code>text<br \/>\n   Switch# clear counters GigabitEthernet 0\/1<br \/>\n   Clear \"show interface\" counters on this interface [confirm] &lt;ENTER&gt;<\/code><\/li>\n<li>Monitor <code>show interfaces GigabitEthernet 0\/1<\/code> over several minutes of sustained traffic to confirm that late collisions and input errors remain at zero.<\/li>\n<\/ol>\n<p>Managing port duplex modes in Cisco switches centers on consistency. Unless you are integrating legacy, non-negotiating endpoints, keep all switch interfaces configured for <code>speed auto<\/code> and <code>duplex auto<\/code> in compliance with IEEE standards. If manual configuration is required, ensure both sides of the link are explicitly forced to identical values, verify the connection using <code>show interfaces status<\/code>, and commit your changes to NVRAM.<\/p>\n<div class='sfsi_Sicons' style='width: 100%; display: inline-block; vertical-align: middle; text-align:left'><div style='margin:0px 8px 0px 0px; line-height: 24px'><span>Please follow and like us:<\/span><\/div><div class='sfsi_socialwpr'><div class='sf_fb_share sf_icon' style='text-align:left;vertical-align: middle;'><a href='https:\/\/www.facebook.com\/sharer\/sharer.php?u=https%3A%2F%2Fcciedump.spoto.net%2Fblog%2Fhow-to-change-duplex-in-cisco-switch_24478.html' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Facebook Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/fbshare_bck.png'  \/><\/a><\/div><div class='sf_twiter sf_icon' style='display: inline-block;vertical-align: middle;width: auto;margin-left: 7px;'>\r\n\t\t\t\t\t\t<a target='_blank' href='https:\/\/twitter.com\/intent\/tweet?text=How+to+Change+Duplex+in+Cisco+Switch+https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html'style='display:inline-block' >\r\n\t\t\t\t\t\t\t<img data-pin-nopin= true width='auto' class='sfsi_wicon' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/visit_icons\/en_US_Tweet.svg' alt='Tweet' title='Tweet' >\r\n\t\t\t\t\t\t<\/a>\r\n\t\t\t\t\t<\/div><div class='sf_pinit sf_icon' style='text-align:left;vertical-align: middle;float:left;line-height: 33px;width:auto;margin: 0 -2px;'><a href='#'  onclick='sfsi_pinterest_modal_images(event,\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\",\"How to Change Duplex in Cisco Switch\")' style='display:inline-block;'  > <img class='sfsi_wicon'  data-pin-nopin='true' width='auto' height='auto' alt='fb-share-icon' title='Pin Share' src='https:\/\/cciedump.spoto.net\/blog\/wp-content\/plugins\/ultimate-social-media-icons\/images\/share_icons\/Pinterest_Save\/en_US_save.svg'  \/><\/a><\/div><\/div><\/div>","protected":false},"excerpt":{"rendered":"<p>Ethernet interfaces operate in either half-duplex or full-duplex mode. In half-duplex mode, an interface cannot send and receive data at the same time, relying on Carrier Sense Multiple Access with Collision Detection (CSMA\/CD) to manage link contention. In full-duplex mode, dedicated transmit and receive paths eliminate collisions entirely, effectively doubling total potential bandwidth. While modern&#8230; &raquo; <a class=\"read-more-link\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\">read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[3,608],"tags":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v18.0 - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>How to Change Duplex in Cisco Switch - SPOTO Official Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Change Duplex in Cisco Switch - SPOTO Official Blog\" \/>\n<meta property=\"og:description\" content=\"Ethernet interfaces operate in either half-duplex or full-duplex mode. In half-duplex mode, an interface cannot send and receive data at the same time, relying on Carrier Sense Multiple Access with Collision Detection (CSMA\/CD) to manage link contention. In full-duplex mode, dedicated transmit and receive paths eliminate collisions entirely, effectively doubling total potential bandwidth. While modern... &raquo; read more\" \/>\n<meta property=\"og:url\" content=\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\" \/>\n<meta property=\"og:site_name\" content=\"SPOTO Official Blog\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-16T02:36:38+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"SPOTO \u7f16\u8f91\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"9 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":[\"Person\",\"Organization\"],\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\",\"name\":\"SPOTO Club\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg\",\"caption\":\"SPOTO Club\"},\"logo\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\"},\"description\":\"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205\",\"sameAs\":[\"https:\/\/cciedump.spoto.net\/\"]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/\",\"name\":\"SPOTO Official Blog\",\"description\":\"Focus on Online IT Training for 20+ Years\",\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}\"},\"query-input\":\"required name=search_term_string\"}],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\",\"name\":\"How to Change Duplex in Cisco Switch - SPOTO Official Blog\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#website\"},\"datePublished\":\"2026-11-16T02:36:38+00:00\",\"dateModified\":\"2026-11-16T02:36:38+00:00\",\"breadcrumb\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/cciedump.spoto.net\/blog\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Change Duplex in Cisco Switch\"}]},{\"@type\":\"Article\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#article\",\"isPartOf\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage\"},\"author\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\"},\"headline\":\"How to Change Duplex in Cisco Switch\",\"datePublished\":\"2026-11-16T02:36:38+00:00\",\"dateModified\":\"2026-11-16T02:36:38+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage\"},\"wordCount\":1374,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638\"},\"articleSection\":[\"CCNA Certification\",\"Cisco Certification\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#respond\"]}]},{\"@type\":\"Person\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1\",\"name\":\"SPOTO \u7f16\u8f91\",\"image\":{\"@type\":\"ImageObject\",\"@id\":\"https:\/\/cciedump.spoto.net\/blog\/#personlogo\",\"inLanguage\":\"en-US\",\"url\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"contentUrl\":\"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155\",\"caption\":\"SPOTO \u7f16\u8f91\"}}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"How to Change Duplex in Cisco Switch - SPOTO Official Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html","og_locale":"en_US","og_type":"article","og_title":"How to Change Duplex in Cisco Switch - SPOTO Official Blog","og_description":"Ethernet interfaces operate in either half-duplex or full-duplex mode. In half-duplex mode, an interface cannot send and receive data at the same time, relying on Carrier Sense Multiple Access with Collision Detection (CSMA\/CD) to manage link contention. In full-duplex mode, dedicated transmit and receive paths eliminate collisions entirely, effectively doubling total potential bandwidth. While modern... &raquo; read more","og_url":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html","og_site_name":"SPOTO Official Blog","article_published_time":"2026-11-16T02:36:38+00:00","twitter_card":"summary_large_image","twitter_misc":{"Written by":"SPOTO \u7f16\u8f91","Est. reading time":"9 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":["Person","Organization"],"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638","name":"SPOTO Club","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/uploads\/2020\/03\/spoto-facemask-96x96.jpg","caption":"SPOTO Club"},"logo":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo"},"description":"SPOTO is an excellent leader in IT certification training for 20+ years. We offer 100% real Cisco CCNA, CCNP exam dumps, CCIE Lab study materials, PMP, CISA, CISM, AWS, Palo Alto, and other IT exam dumps. We have helped thousands of candidates around the world to pass their IT exams on the first try! As the first-class online IT training organization in China, SPOTO cooperates with many giant Internet companies in China like Tencent, Baidu, and Alibaba. What\u2019s more, we have won lots of awards in IT education training such as \u201cTop Ten Influential Brands In Online Education Industry\u201d given by Baidu, \u201cOfficial IT Online Training Organization\u201d awarded by Tencent Class, etc. Join us: https:\/\/cciedump.spoto.net\/ Contact us: E-mail: support@spoto.net Phone \/ WhatsApp: +86 18344981205","sameAs":["https:\/\/cciedump.spoto.net\/"]},{"@type":"WebSite","@id":"https:\/\/cciedump.spoto.net\/blog\/#website","url":"https:\/\/cciedump.spoto.net\/blog\/","name":"SPOTO Official Blog","description":"Focus on Online IT Training for 20+ Years","publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/cciedump.spoto.net\/blog\/?s={search_term_string}"},"query-input":"required name=search_term_string"}],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage","url":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html","name":"How to Change Duplex in Cisco Switch - SPOTO Official Blog","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#website"},"datePublished":"2026-11-16T02:36:38+00:00","dateModified":"2026-11-16T02:36:38+00:00","breadcrumb":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/cciedump.spoto.net\/blog"},{"@type":"ListItem","position":2,"name":"How to Change Duplex in Cisco Switch"}]},{"@type":"Article","@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#article","isPartOf":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage"},"author":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1"},"headline":"How to Change Duplex in Cisco Switch","datePublished":"2026-11-16T02:36:38+00:00","dateModified":"2026-11-16T02:36:38+00:00","mainEntityOfPage":{"@id":"https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#webpage"},"wordCount":1374,"commentCount":0,"publisher":{"@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/25594d4796697ccb1ef63d55c269c638"},"articleSection":["CCNA Certification","Cisco Certification"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/cciedump.spoto.net\/blog\/how-to-change-duplex-in-cisco-switch_24478.html#respond"]}]},{"@type":"Person","@id":"https:\/\/cciedump.spoto.net\/blog\/#\/schema\/person\/4edd6074d9632c14eda17a2205a88dd1","name":"SPOTO \u7f16\u8f91","image":{"@type":"ImageObject","@id":"https:\/\/cciedump.spoto.net\/blog\/#personlogo","inLanguage":"en-US","url":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","contentUrl":"https:\/\/cciedump.spoto.net\/blog\/wp-content\/litespeed\/avatar\/f525ded90e4ff384a19ebdbe47c80d22.jpg?ver=1794560155","caption":"SPOTO \u7f16\u8f91"}}]}},"_links":{"self":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24478"}],"collection":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/comments?post=24478"}],"version-history":[{"count":0,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/posts\/24478\/revisions"}],"wp:attachment":[{"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/media?parent=24478"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/categories?post=24478"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/cciedump.spoto.net\/blog\/wp-json\/wp\/v2\/tags?post=24478"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}